|
| LinkBack | Thread Tools | Display Modes |
12-27-2012, 04:04 PM | #1 |
Newbie Join Date: Dec 2012 Location: West Linn
Posts: 6
| Axial wraith not turning
I just recently got an axial wraith for christmas and today i dont know what happened i try to turn it left it wont work i try to turn it right it wont work. So then i lifted the front wheels off the ground and it will turn but it wont stay straight when i let go of the wheel. any suggestions. P.s. its the rtr completely bone stock
|
Sponsored Links | |
12-27-2012, 04:06 PM | #2 |
Rock Crawler Join Date: Oct 2011 Location: Warren
Posts: 722
|
Check to see if your servo horn is tight. Sounds like it is either loose or you may have stripped it. Sent from my Desire HD using Tapatalk 2 |
12-27-2012, 07:38 PM | #3 |
Rock Crawler Join Date: Dec 2005 Location: East Texas
Posts: 870
| Re: Axial wraith not turning
Sounds like servo arm is stripped. Snag an aluminum one and you will be good to go.
|
12-28-2012, 06:39 AM | #4 |
RCC Addict Join Date: Dec 2011 Location: Raleign
Posts: 1,439
| Re: Axial wraith not turning
My RTR had a crap servo horn out of the box too. Pull the servo horn off, check it out, and put it back together. When you do that make sure you turn everything on and center the steering servo with 0 trim. Then when you put it on you'll need to center it back because you're always a half a spline off |
12-28-2012, 01:47 PM | #5 |
Newbie Join Date: Dec 2012 Location: West Linn
Posts: 6
| Re: Axial wraith not turning
im pretty newbie with this stuff so i am kind of confused
|
12-28-2012, 01:57 PM | #6 |
Quarry Creeper Join Date: Dec 2011 Location: The land of snow
Posts: 312
|
Servo horn is the plastic arm that connects the servo gear to the steering linkage. The servo is the little box bolted to your front axle that makes the noise when you turn. The plastic teeth in the horn often strip so the servo just spins inside of it instead of moving the arm left to right
|
12-28-2012, 02:08 PM | #7 |
Newbie Join Date: Dec 2012 Location: West Linn
Posts: 6
| Re: Axial wraith not turning
so should i go ahead and order an aluminum then i cause i just took a look and its stripped
|
12-28-2012, 02:14 PM | #8 |
Newbie Join Date: Dec 2012 Location: West Linn
Posts: 6
| Re: Axial wraith not turning
another question do you guys recommend any other upgrades for my truck to make sure some other stuff doesnt go wrong
|
12-28-2012, 04:37 PM | #9 |
I wanna be Dave Join Date: Nov 2010 Location: 07456 N. NJ USofA
Posts: 8,314
| Re: Axial wraith not turning Since it's stripped, then yes, get a new one so you can turn. I would recommend an aluminum clamping type servo arm/horn. I usually use one made by GHRacing (AKA, Golden Horizons Racing). You need to see the "spline count" to get the correct one though. |
12-28-2012, 05:37 PM | #10 |
Newbie Join Date: Dec 2012 Location: West Linn
Posts: 6
| Re: Axial wraith not turning
when u get a new horn does it have to be meant for the same servo or brand or just the same number of teeth
|
12-28-2012, 07:44 PM | #11 |
Rock Crawler Join Date: Mar 2011 Location: hampton
Posts: 984
| Re: Axial wraith not turning
just the number of teeth,brand dont matter. iv never had a axial servo, so i cant help ya with tooth count
|
12-29-2012, 12:19 AM | #12 |
Newbie Join Date: Dec 2012 Location: West Linn
Posts: 6
| Re: Axial wraith not turning
thanks guys i appreciate it most come with about 25 teeth by the way
|
Tags |
axial, electronics, problem, turning, wraith |
Axial wraith not turning - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Turning my Wraith into a racer/basher | cnj | Axial Wraith | 18 | 08-17-2012 11:14 AM |
Axial scx-10 not turning | Brewedintexas | Electronics | 2 | 08-18-2011 01:59 AM |
Axial scx10 honcho turning | bigdoghayden | General Crawlers | 4 | 02-10-2011 04:01 PM |
Help with axial scx10 turning | bigdoghayden | General Crawlers | 5 | 02-10-2011 10:31 AM |
Axial ax10 stutters when turning right....HELP! | LexieVW | Newbie General | 6 | 05-28-2009 09:00 PM |
Thread Tools | |
Display Modes | |
| |