07-18-2012, 06:30 AM | #1 |
Newbie Join Date: Jul 2012 Location: gallatin
Posts: 11
| wiring bec/servo/esc
i have a savox 444.oz servo mmp esc and a ccbec what is the best way to wire them ! I have heard that if i wire it thru the rx it will frie it!
|
Sponsored Links | |
07-18-2012, 06:38 AM | #2 |
Pebble Pounder Join Date: Aug 2011 Location: Gresham, OR
Posts: 146
| Re: wiring bec/servo/esc |
07-18-2012, 06:47 AM | #3 |
Rock Stacker Join Date: Oct 2010 Location: Birmingham
Posts: 73
|
It may work through the esc but I do not believe it will draw enough to work at its full potential. Disconnect the power wire in the esc plug and tape it up, solder bec to your battery connector with the esc wires, plug everything up normally with the bec in the third slot on receiver |
07-18-2012, 07:55 AM | #4 | |
Newbie Join Date: Jul 2012 Location: gallatin
Posts: 11
| Re: wiring bec/servo/esc Quote: i have already fried one rx . i am just wondering is there a better way ? | |
07-18-2012, 08:06 AM | #5 |
I wanna be Dave Join Date: Jan 2004 Location: Detroit
Posts: 3,583
| Re: wiring bec/servo/esc
Here is best way to wire BEC direct to the Servo. question on BEC Note: The ESC needs a red wire in the plug to power the Receiver now unlike the earlier posted image. |
07-18-2012, 08:43 AM | #6 |
Proverbial threadkiller Join Date: Feb 2011 Location: Central Wisconsin
Posts: 1,453
| Re: wiring bec/servo/esc I know at least three vendors here on RCC sell a bypass adapter. Costs $5-$6, plug in your servo, plug in your BEC, plug that whole apparatus into your receiver (steering channel), Bam. No pulling wires, taping anything off, and no worrying about the voltage to your receiver.
|
07-18-2012, 09:05 AM | #7 |
Pebble Pounder Join Date: Nov 2011 Location: Rhode Island
Posts: 183
| Re: wiring bec/servo/esc |
07-18-2012, 11:54 AM | #8 |
Quarry Creeper Join Date: Dec 2009 Location: Honolulu
Posts: 428
| Re: wiring bec/servo/esc
I made mine so I could move it from rig to rig. |
07-18-2012, 02:25 PM | #9 |
Quarry Creeper Join Date: Dec 2009 Location: Honolulu
Posts: 428
| Re: wiring bec/servo/esc
End result: |
07-18-2012, 02:31 PM | #10 | |
Newbie Join Date: Jul 2012 Location: gallatin
Posts: 11
|
ok thanks that is what i was looking for ! has this set up worked for other people ? Quote: i do like how you anunciate ! LOL were did you get this Y- Harness Last edited by THX_138; 07-23-2012 at 10:41 AM. | |
07-18-2012, 02:46 PM | #11 |
Quarry Creeper Join Date: Dec 2009 Location: Honolulu
Posts: 428
| Re: wiring bec/servo/esc
"Y" harness is from my local hobby shop. I'm sure it's easily available online.
|
05-03-2015, 08:02 PM | #12 |
Pebble Pounder Join Date: Feb 2015 Location: in my house
Posts: 138
| Re: wiring bec/servo/esc
You can get the "Y" harnesses from amazon- just type in "Futaba Y Harness"
|
05-03-2015, 09:23 PM | #13 |
Newbie Join Date: Feb 2012 Location: Ramona, Kali.
Posts: 35
| Re: wiring bec/servo/esc
I notice the diagram linked in response #5 does not connect the negative from the xceiver to the BEC & servo whereas this one does. Not sure if it matters, but I did mine as listed here. Might cut down on some noise/interferance?
|
01-10-2016, 06:47 AM | #14 |
Newbie Join Date: Oct 2015 Location: portland
Posts: 1
| Re: wiring bec/servo/esc |
01-10-2016, 03:01 PM | #15 |
Quarry Creeper Join Date: Oct 2010 Location: Montreal, QC
Posts: 213
| Re: wiring bec/servo/esc
Here is what i did. I adjusted 4 BEC to 7.4v then sent them to Heyok so he could modify them to be "no brainer bec" with dual output. Perfect for servo and winches! Here is how they came back: End results are awesome! Plug and play at its finest! |
01-10-2016, 10:39 PM | #16 | |
Proverbial threadkiller Join Date: Feb 2011 Location: Central Wisconsin
Posts: 1,453
| Re: wiring bec/servo/esc Quote:
Just connect all the signal wires as they're labeled on that picture. Make sure you pull or cut the red wire on the connector that plugs into your receiver (in the steering port). Then your ESC's signal wires would plug into the receiver in the ESC port (typically channel 2). You pulled the red wire out from the connector in the steering port, right? Then you do not pull or cut the red on your ESC's signal wires connector. Just plug your ESC into the receiver with all three wires intact. Take your time, follow the picture you have up, and you should be fine. | |
wiring bec/servo/esc - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Wiring Help\Question ESC,RX,Servo,BEC | mnickolson | Electronics | 2 | 06-27-2012 10:47 AM |
Wiring Bec directly to servo | xj_man_646 | Newbie General | 5 | 03-13-2010 02:18 PM |
cc bec to servo wiring | timo992001 | Electronics | 3 | 03-24-2009 08:53 PM |
ESC / Servo / BEC Wiring Questions??? | RCholic | Electronics | 1 | 09-18-2007 06:11 AM |
| |