Go Back   RCCrawler Forums > RCCrawler General Tech > Electronics
Loading

Notices

Thread: mmp tekin roc setup issue

Reply
 
LinkBack Thread Tools Display Modes
Old 03-06-2013, 01:42 PM   #1
Pebble Pounder
 
Join Date: Jun 2012
Location: las cruces
Posts: 193
Default mmp tekin roc setup issue

so i got my roc today and shit wont work the motor just studders and the drive shafts only turn 180* idk what the issue is the esc wasent arming also i know its prob somthing im doing wrong but it worked fine today with my brushed motor now after i change the setting to brushless it isnt working im so frustrated i could punch a kitten anyone have a idea
danmac is offline   Reply With Quote
Sponsored Links
Old 03-06-2013, 01:48 PM   #2
Moderator
 
badhoopty's Avatar
 
Join Date: Jan 2004
Location: chicago
Posts: 2,814
Default Re: mmp tekin roc setup issue

Quote:
Originally Posted by danmac View Post
so i got my roc today and shit wont work the motor just studders and the drive shafts only turn 180* idk what the issue is the esc wasent arming also i know its prob somthing im doing wrong but it worked fine today with my brushed motor now after i change the setting to brushless it isnt working im so frustrated i could punch a kitten anyone have a idea
i would go through the esc setup again.
badhoopty is offline   Reply With Quote
Old 03-06-2013, 01:56 PM   #3
Pebble Pounder
 
Join Date: Jun 2012
Location: las cruces
Posts: 193
Default Re: mmp tekin roc setup issue

i have i even reset to default and it still just kinda vibrated back and forth
danmac is offline   Reply With Quote
Old 03-06-2013, 02:31 PM   #4
Rock Crawler
 
Join Date: Feb 2012
Location: Michigan
Posts: 617
Default Re: mmp tekin roc setup issue

Check your sensor cable. Make sure ESC is in sensored only mode.
DRTMI is offline   Reply With Quote
Old 03-06-2013, 02:45 PM   #5
Quarry Creeper
 
Join Date: Jan 2010
Location: Lunenburg
Posts: 349
Default

Try running it without the sensor cable plugged in. ESC can be set to Smart Sense.

If the motor works, its most likely the cable. Also double check ESC to motor wires, A-A, B-B and C-C.
Hobine is offline   Reply With Quote
Old 03-06-2013, 02:59 PM   #6
Pebble Pounder
 
Join Date: Jun 2012
Location: las cruces
Posts: 193
Default Re: mmp tekin roc setup issue

i think it might of been the sensor cable i took it out and back in and it works and shit cock is it fast waaaaaaaay fast in a scx10
danmac is offline   Reply With Quote
Old 03-06-2013, 03:00 PM   #7
Pebble Pounder
 
Join Date: Jun 2012
Location: las cruces
Posts: 193
Default Re: mmp tekin roc setup issue

thanks for all the help guys and is no insta reverse a brushless thing
danmac is offline   Reply With Quote
Old 03-06-2013, 03:22 PM   #8
Quarry Creeper
 
Join Date: Jan 2010
Location: Lunenburg
Posts: 349
Default

Quote:
Originally Posted by danmac View Post
thanks for all the help guys and is no insta reverse a brushless thing
If you want instant reverse, set to "crawler reverse" in the programming. Be careful though, slamming a high powered brushless right into reverse is a good way to break driveshafts and strip gears.
Hobine is offline   Reply With Quote
Old 03-06-2013, 05:19 PM   #9
RCC Addict
 
Join Date: Dec 2011
Location: Raleign
Posts: 1,439
Default Re: mmp tekin roc setup issue

Definitely check A-A, B-B, and C-C and sensor cable. The cable is tough to plug into motor and ESC. Don't push too hard or you'll snap the connector off the ESC (don't ask me how I know :( )
ik632 is offline   Reply With Quote
Old 03-06-2013, 07:15 PM   #10
Pebble Pounder
 
Join Date: Nov 2012
Location: on the edge!
Posts: 187
Default Re: mmp tekin roc setup issue

I'm looking for a FAST setup for my Ridgcrest I have a HH 27t Torquemaster with a BRXL and that is a sweet set up but I want fast, 4s kinda speed. Do you think your set up is worth me looking at?
04zrx is offline   Reply With Quote
Old 03-06-2013, 07:52 PM   #11
Pebble Pounder
 
Join Date: Jun 2012
Location: las cruces
Posts: 193
Default Re: mmp tekin roc setup issue

hell yea i dont even think i could control it on 3s or 4s
danmac is offline   Reply With Quote
Old 03-06-2013, 07:58 PM   #12
Pebble Pounder
 
Join Date: Nov 2012
Location: on the edge!
Posts: 187
Default Re: mmp tekin roc setup issue

so what exactly do you have for a Speed controller and what motor are you running? I will need to get it all since my speed controller is for brushed only. I have 2s, 3s and 4s to use if I want.
04zrx is offline   Reply With Quote
Old 03-06-2013, 09:28 PM   #13
Pebble Pounder
 
Join Date: Jun 2012
Location: las cruces
Posts: 193
Default Re: mmp tekin roc setup issue

I hve a mamba max pro with a tekin roc 3100kv
danmac is offline   Reply With Quote
Old 03-09-2013, 01:11 PM   #14
RCC Addict
 
Join Date: Dec 2011
Location: Raleign
Posts: 1,439
Default Re: mmp tekin roc setup issue

It's definitely good in the Wraith. I'm running 12/58 right now in 32 pitch gears. Speed on 2s is good and 3s is great.
ik632 is offline   Reply With Quote
Reply



mmp tekin roc setup issue - Similar Threads
Thread Thread Starter Forum Replies Last Post
tekin roc danmac Electronics 6 03-03-2013 01:08 AM
MMP and Tekin Roc 412 Onebdgti Electronics 0 02-23-2013 08:07 AM
MMP/tekin setup seaturtle Axial Wraith 9 01-17-2013 03:12 PM
MMP issue... i think i'm the issue. concretejungle Electronics 12 08-13-2012 02:52 PM
MMP & Tekin sensored 13.5 issue hasbeen Axial Wraith 10 11-01-2011 07:32 PM
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -6. The time now is 04:00 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com