|
| LinkBack | Thread Tools | Display Modes |
07-02-2013, 11:44 AM | #1 |
RCC Addict Join Date: Mar 2009 Location: Interior BC
Posts: 1,786
| cogging with tekin 13.5t?
i had this issue with my tekin 13.5t redline and swapped it out with a brushed type. Thing is....i kinda want my brushless back! lol problem i was having was cogging and even had purchased a new sensor wire with failed success. Using a MMP and 58/12t setup (32p) there is no binding and im also using a 5300mah 2s lipo for this. any ideas? |
Sponsored Links | |
07-02-2013, 01:29 PM | #2 |
RCC Addict Join Date: Feb 2008 Location: Tekin, ID
Posts: 1,940
| Re: cogging with tekin 13.5t?
Has the 13.5 ever been wet? It may need a new sensor PCB. If you have a Tekin ESC you can use the sensor checker feature to see if they are operating correctly.
|
07-02-2013, 01:31 PM | #3 |
RCC Addict Join Date: Sep 2011 Location: Beavercreek, Oregon, USA
Posts: 1,950
| Re: cogging with tekin 13.5t?
Did you have your MMP set for Smart Sense mode or Sensored Only mode?
|
07-02-2013, 01:36 PM | #4 |
RCC Addict Join Date: Mar 2009 Location: Interior BC
Posts: 1,786
| Re: cogging with tekin 13.5t? |
07-02-2013, 01:36 PM | #5 |
RCC Addict Join Date: Mar 2009 Location: Interior BC
Posts: 1,786
| Re: cogging with tekin 13.5t? |
07-02-2013, 01:37 PM | #6 |
RCC Addict Join Date: Feb 2008 Location: Tekin, ID
Posts: 1,940
| Re: cogging with tekin 13.5t? |
07-02-2013, 01:42 PM | #7 |
RCC Addict Join Date: Mar 2009 Location: Interior BC
Posts: 1,786
| Re: cogging with tekin 13.5t? |
07-02-2013, 01:48 PM | #8 |
RCC Addict Join Date: Sep 2011 Location: Beavercreek, Oregon, USA
Posts: 1,950
| Re: cogging with tekin 13.5t? |
07-02-2013, 01:55 PM | #9 |
RCC Addict Join Date: Mar 2009 Location: Interior BC
Posts: 1,786
| Re: cogging with tekin 13.5t? |
07-02-2013, 03:15 PM | #10 |
I wanna be Dave Join Date: Feb 2004 Location: on a Big Rock
Posts: 7,837
| Re: cogging with tekin 13.5t? |
07-05-2014, 03:04 PM | #11 |
Newbie Join Date: Apr 2014 Location: nevada city
Posts: 4
| Re: cogging with tekin 13.5t?
I also have the same gogging problem. Yes corrosion x
|
07-05-2014, 03:06 PM | #12 |
Newbie Join Date: Apr 2014 Location: nevada city
Posts: 4
| Re: cogging with tekin 13.5t?
I mean cogging.
|
07-05-2014, 03:25 PM | #13 |
Rock Crawler Join Date: May 2012 Location: Washougal
Posts: 625
| Re: cogging with tekin 13.5t?
Gearing lower will help. I gear as low as I can, 93/12, and it runs super smooth. With the 32p you should be able to fit 66/10, but don't quote me, its been awhile. The lower gearing will help your drag brake too. Esc settings would be the next thing to look at. With the lower gearing you should think about running 3s or even 4s to get your wheel speed back. Good luck, getting a brushless dialed for crawling can be tricky. |
07-05-2014, 06:40 PM | #14 |
Quarry Creeper Join Date: Feb 2013 Location: hawkins
Posts: 391
| Re: cogging with tekin 13.5t?
i run 64/9 on my 11 pound rig on 4s it screams when i first set it up i ran 12 60 and it cogged like crazy
|
cogging with tekin 13.5t? - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Cogging with MMP 13.5 Tekin | danbillyboo | Electronics | 8 | 02-03-2013 10:11 PM |
cogging with tekin 13.5t? | SwampDawg | Axial Wraith | 15 | 09-25-2012 04:18 PM |
New Tekin 13.5 cogging? | lkracer | Axial Wraith | 12 | 08-16-2012 08:16 PM |
Tekin 13.5 just cogging or bad MMP? | Checkitout0125 | Electronics | 11 | 01-17-2012 07:28 AM |
Thread Tools | |
Display Modes | |
| |