| |
| |||||||
 |
| | LinkBack | Thread Tools | Display Modes |
07-10-2013, 09:36 PM
| #1 |
| Newbie Join Date: Oct 2005 Location: Millstadt
Posts: 13
|  converted twin hammers to brxl, 3rd channel don't work. 4pl
I Put a brxl and hh 27 in my Twin hammers... if I plug in the battery with shift servo in channel 3 unplugged, runs and drives fine. If I plug in channel 3 and try to drive it. the motor won't run at all. Disconnect channel 3 while still on and then it drives fine again, plug it in while working and doesn't move again. What could be the issue? Also tried the shift servo programmed to channel 4 on the receiver and same thing happens.. I'm losttt !
|
|  |
| Sponsored Links | |
| | |
|
07-11-2013, 12:24 AM
| #2 |
| Rock Crawler  Join Date: Oct 2012 Location: Casper
Posts: 620
| Re: converted twin hammers to brxl, 3rd channel don't work. 4pl
Does the shift servo have it's own power supply? Like, from a BEC or separate battery?
|
|
| |
|
07-11-2013, 07:10 AM
| #3 |
| I wanna be Dave Join Date: May 2007 Location: Vancouver, BC
Posts: 2,375
| Re: converted twin hammers to brxl, 3rd channel don't work. 4pl
Maybe the shift servo has failed and has a short in it, causing the receiver to shut down whenever you plug in the shift servo. Does the steering also stop working when you plug in the shift servo? |
|
| |
|
07-11-2013, 07:41 AM
| #4 |
| Rock Crawler Join Date: May 2012 Location: Columbus
Posts: 676
| Re: converted twin hammers to brxl, 3rd channel don't work. 4pl
iv been thinking of converting a EXO to a wraith
|
|
| |
|
07-11-2013, 08:10 AM
| #5 | |
| RCC Addict Join Date: Mar 2007 Location: Turn the mayflower around.. it will never work
Posts: 1,588
| Re: converted twin hammers to brxl, 3rd channel don't work. 4pl Quote:
 | |
|
| |
|
07-11-2013, 09:40 AM
| #6 |
| I wanna be Dave Join Date: Dec 2006 Location: Goin broke losing weight.....
Posts: 2,262
| Re: converted twin hammers to brxl, 3rd channel don't work. 4pl
When I switched things out, mine would not run unless I powered the steer servo directly w a bec, and ran shift servo off rx powered by esc bec. I did not run bec to rx, only servo, servo signal to rx |
|
| |
|
07-11-2013, 09:52 AM
| #7 | |
| Rock Crawler Join Date: Aug 2011 Location: Perth west oz
Posts: 944
| Re: converted twin hammers to brxl, 3rd channel don't work. 4pl Quote:
| |
|
| |
|
07-11-2013, 11:49 AM
| #8 |
| Rock Crawler Join Date: May 2012 Location: Columbus
Posts: 676
| Re: converted twin hammers to brxl, 3rd channel don't work. 4pl
really??
Last edited by Ohioskills; 07-11-2013 at 11:57 AM. |
|
| |
|
converted twin hammers to brxl, 3rd channel don't work. 4pl - Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Savage00's Twinny Twin Twin Hammers | Savage00 | Vaterra Twin Hammers | 16 | 09-19-2013 09:09 PM |
| Can I get my Futaba 3PM 3rd channel to work a servo to toggle my light switch? | jedi | Newbie General | 2 | 08-10-2009 08:12 AM |
| Getting 3rd channel on rc4wd radio to work | spdyracer | Electronics | 7 | 07-31-2009 06:22 PM |
| Thread Tools | |
| Display Modes | |
| |
Linear Mode
