| |
11-07-2013, 07:57 AM
| #1 |
| Quarry Creeper Join Date: Oct 2013 Location: Nanaimo
Posts: 221
| 
Hey all i was just wondering what the difference between a bec design for a plane and and one designed for cars. Only difference i see is that my car bec has the white wire going from the bec to the receiver and the ones for planes does not, just two. What is the function of the white wire on a car bec? Really no one else knows either! It is wired as per instructions and as you can see there is a signal wire from bec to receiver.  So what is its function? Last edited by THX_138; 11-10-2013 at 09:35 PM. |
|  |
| Sponsored Links | |
| | |
|
11-08-2013, 10:53 PM
| #2 |
| Rock Crawler Join Date: Apr 2009 Location: NE Ohio
Posts: 794
| Re: Bec help
You should try posting this in the electronics thread you'd get a lot more answers. As far as becs go a bec is a bec. The wire you see is the signal wire and shouldn't run the to the Esc unless you do not have an Esc with an internal bec. If you run it to the Esc it will cause problems causing the Esc to malfunction or burn up the internal one. --Dan Last edited by sickcivic95; 11-10-2013 at 05:44 PM. |
|
| |
|
11-10-2013, 04:50 PM
| #3 |
| Rock Crawler  Join Date: Nov 2010 Location: the 'burgh'
Posts: 976
| Re: Bec help
Yep, but if you look close the signal wire from the ESC is disconnected.  |
|
| |
|
11-10-2013, 04:58 PM
| #4 |
| Rock Crawler Join Date: Apr 2009 Location: NE Ohio
Posts: 794
| Re: Bec help
Check out this link it gives you a ton of detail on it Definitive Radio, Power Wiring, BEC and Servo Threads-- RCC's Top Tech Threads! --Dan |
|
| |
|
11-10-2013, 05:52 PM
| #5 |
| I wanna be Dave Join Date: Aug 2006 Location: under a rock and a hard place
Posts: 5,443
| Re: Bec help
What BEC are you using ? A CC 10 amp bec has an orange signal wire and it is used solely for programming the bec. It does not need to be removed whem plugged into the rx. I do not know if other bec's are the same... You def need to remove the red wire from the esc going to the rx when using an external bec as the diagram shows. |
|
| |
|
11-10-2013, 10:26 PM
| #6 |
| Quarry Creeper Join Date: Oct 2013 Location: Nanaimo
Posts: 221
|
Ok makes sense im using a novak and its programable too. Thnx Q answered!
|
|
| |
 |
Bec help - Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| BRXL+Castle Link+Bec=? How do i set BEC? | crazyorigin | Electronics | 17 | 11-21-2011 03:11 PM |
| Built in bec vs. Rooster Crawler bec for glitching | mudking82 | Axial AX-10 Scorpion | 7 | 12-07-2010 08:57 AM |
| using external BEC & esc's internal BEC.... | slowlearner | Newbie General | 2 | 02-14-2010 01:35 AM |
| Castle BEC & Castle Link - not finding BEC | Locked Up | Electronics | 22 | 12-20-2007 03:37 PM |
| Receiver BEC (vs ESC BEC) | sim | Electronics | 7 | 10-13-2005 07:54 PM |
| Thread Tools | |
| Display Modes | |
| |
Linear Mode
