07-16-2014, 01:55 AM | #1 |
Rock Crawler Join Date: Aug 2011 Location: Perth west oz
Posts: 944
| BR-mini won't Arm
Hi I bought a pro rig with dual BR-mini, when I got the rig, it worked fine for 2mins, then the rear motor stopped. I thought was the LVC cut in because the battery is not full. So I proceed to strip down the rig and rebuild it. Now I have rewired and rebuild it, the rear ESC wont arm, it beep a little but not complete. The green led flashing. I swap ESC and motor and Rx port, problem lies with the rear ESC. I also have a little play with the dead bandwidth, no avail. What could be the problem? Where can I find a list of HH ESC LED indicator flashing definition? |
Sponsored Links | |
07-16-2014, 09:13 PM | #2 |
Rock Crawler Join Date: May 2013 Location: Somewhere in space
Posts: 931
| Re: BR-mini won't Arm
Maybe you could contact HH and get a replacement, eh? Hmm..how old is that ESC?
|
07-17-2014, 07:34 AM | #3 |
Rock Crawler Join Date: Aug 2011 Location: Perth west oz
Posts: 944
| Re: BR-mini won't Arm
Not sure, it came with the rig. Ok will try to contact HH. But I thought JRH will be able to see this thread and shed some light here.
|
07-17-2014, 01:03 PM | #4 |
RCC Addict Join Date: Oct 2011 Location: British Columbia
Posts: 1,487
| Re: BR-mini won't Arm
JRH doesn't spend a lot of time on the forums. Did you buy the rig with controller? If not and using your controller, I'd try calibrating the ESC's to it. Trims at zero/neutral. |
07-17-2014, 08:00 PM | #5 | |
Rock Crawler Join Date: Aug 2011 Location: Perth west oz
Posts: 944
| Re: BR-mini won't Arm Quote:
Can't get it going. | |
07-17-2014, 09:30 PM | #6 |
RCC Addict Join Date: Oct 2011 Location: British Columbia
Posts: 1,487
| Re: BR-mini won't Arm
Well, going by Castle's error code chart, throttle EPA's aren't high enough. If you're at 100% now, try 105%. Not sure how close Castle's error codes are to JRH's mini, but his ESC's have been based on Castle circuitry in the past. |
07-18-2014, 05:55 AM | #7 |
RCC Addict Join Date: Jun 2011 Location: Lindsborg
Posts: 1,708
|
What radio, I am seeing an issue with hacked Gt3bs and the full size Esc. I found playing with the trim during arm gets it to connect. But then the trim is off.
|
07-18-2014, 06:46 AM | #8 |
owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down!
Posts: 20,290
| Re: BR-mini won't Arm
Blinking green = forward throttle signal. It won't arm until it sees neutral, adjust your trim for the channel.
|
07-18-2014, 09:58 AM | #9 | |||
Rock Crawler Join Date: Aug 2011 Location: Perth west oz
Posts: 944
| Re: BR-mini won't Arm Quote:
Quote:
Quote:
Actually the green light blinks very quickly to almost constant. I have taken a little video to show what happened when I plugged in with zero trim and 100% EPA. Br-mini wont arm - YouTube | |||
07-18-2014, 10:01 AM | #10 |
owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down!
Posts: 20,290
| Re: BR-mini won't Arm
Try another channel to see if it will arm like the other, still points to neutral trim being off. Be sure you didn't reverse a mix or something. There are radios where you can't hit proper neutral without flipping the channel or mix. If that doesn't work, send it in with the information requested on our site warranty tab. |
07-18-2014, 09:17 PM | #11 |
Rock Crawler Join Date: Aug 2011 Location: Perth west oz
Posts: 944
| Re: BR-mini won't Arm
Try channel 1, 3 and 4 with neutral trim and all, no different, guess I will be sending it in. BTW, where can I find a list of definition of the LEDs? It will solve a lot of problems just by knowing why the LED is flashing. |
07-18-2014, 09:27 PM | #12 |
owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down!
Posts: 20,290
| Re: BR-mini won't Arm |
07-18-2014, 09:29 PM | #13 |
owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down!
Posts: 20,290
| Re: BR-mini won't Arm
I see it needs some clarification, I'll work on that Also, in Australia you can use one ten crawlers for faster warranty service. |
07-19-2014, 10:03 AM | #14 |
Rock Crawler Join Date: Aug 2011 Location: Perth west oz
Posts: 944
| Re: BR-mini won't Arm
I have already contacted highlucks (cameron), i have also written to your shop and jonathon is looking into it. Thanks.
Last edited by Colgout; 07-19-2014 at 08:17 PM. |
07-19-2014, 10:23 AM | #15 |
owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down!
Posts: 20,290
| Re: BR-mini won't Arm
And thats why I'm not really needed for tech support anymore, but sometimes I have the time to try anyway! |
07-19-2014, 08:19 PM | #16 |
Rock Crawler Join Date: Aug 2011 Location: Perth west oz
Posts: 944
| Re: BR-mini won't Arm
I post here just to make sure is not something simple, and if it can be resolved, others can learn it too.
|
BR-mini won't Arm - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
servo arm | irollgen4s | Axial Wraith | 14 | 12-29-2011 02:10 PM |
Arm of Awesome | constantmotion | Chit Chat | 12 | 06-03-2010 02:26 PM |
Losi Mini LST2, Traxxas Mini Slash, or Mini revo. | CrawlinMike | Non Crawler RC's | 10 | 07-14-2009 06:53 PM |
servo arm? | sirwin47 | Newbie General | 10 | 02-26-2009 02:24 PM |
| |