Re: Have tech questions? Will answer. If I absolutely have to, can I use a brushed motor with my Mamba X? (provided I can put the right connectors on the motor) Sent from my Nexus 5 using Tapatalk |
Re: Have tech questions? Will answer. Quote:
Sent from my SM-N920V using Tapatalk |
Re: Have tech questions? Will answer. What is the purpose of these capacitors on the stock 35 turn dynamite brushed motor in my vaterra ascender? I'm replacing it with a Holmes hobbies trailmaster sport 55turn and should I install these on the new motor? Still using stock vaterra ascender esc. Thanks! https://uploads.tapatalk-cdn.com/201...4d7cc17e33.jpg Sent from my iPhone using Tapatalk |
Re: Have tech questions? Will answer. Quote:
Quote:
|
Re: Have tech questions? Will answer. What's the difference between "crawlmaster pro 13t" and the now limited edition "custom pro 13t" more punch? Smoothness? Low end? I assume wheel speed is the same on the 13t's?.. I already ordered one but love to know a little more about it [emoji106] Sent from my iPhone using Tapatalk |
Re: Have tech questions? Will answer. Heavier wire gauge gives better punch and better efficiency under load. You may notice a little increase in wheelspeed as well, depends on gearing. |
Re: Have tech questions? Will answer. I'm running a PP-2200kv in my SCX10.2 with 56/11 gear ratio. I ran it for about 45 minutes (mainly slow crawling) and the data log from my Mamba X shows that the maximum current draw was only 12amps. Is this a reasonable reading? If this figure is reliable, then I really don't need to buy high C rating lipo packs right? Thank you. |
Re: Have tech questions? Will answer. Short answer: yes. The X esc's don't have the refresh rate to catch the absolute peak, but that number is close... It's a crawler, they draw almost no current. C ratings are all made up anyway. :lmao: |
Re: Have tech questions? Will answer. Quote:
Sent from my Nexus 5 using Tapatalk |
Re: Have tech questions? Will answer. I'm a little confused. Regarding the new HV500V2. In a post it was stated that it is capable of 2-3 S but the tech. spec. on the website only say 2 S compatible like the old version. What are now the correct specs. |
Re: Have tech questions? Will answer. Directly cut & pasted from HH website (Bold are the differences, highlighted by me): SHV500 V2 FEATURES: Water-Resistant Alloy Case with O-Ring Seals All Metal machined gears with improved pin strength Upgraded Brushless Super motor with 200C rated magnets 24cm radio signal lead 24cm 12v power lead with female JST plug, includes male extension 2s through 4s Lipo compatible 1 Year Warranty SPECIFICATIONS: Weight: 73g Dimensions: 41x20x40mm Spline: 25 tooth (Futaba type) M3 threaded Torque @ 11.1v: 32.4 kg/cm (450 oz/inch) Speed @ 11.1v: 0.10 sec Torque @ 14v: 37.5 kg/cm (520 oz/inch) Speed @ 14v: 0.08 sec _______________________________________ SHV500 FEATURES: Water-Resistant Alloy Case O-Ring Seals All Metal Gears Brushless Super High Voltage motor Upgraded N38EH 200c rated magnets 24cm radio lead 24cm 12v power lead with female JST plug and 75mm male JST extension 3s Lipo compatible (16v max) 1 Year Warranty SPECIFICATIONS: Weight: 73g Dimensions: 41x20x40mm Spline: 25 tooth (Futaba type) M3 threaded Torque @ 11.1v: 32.4 kg/cm (450 oz/inch) Speed @ 11.1v: 0.10 sec Torque @ 14v: 37.5 kg/cm (520 oz/inch) Speed @ 14v: 0.08 sec |
Re: Have tech questions? Will answer. Quote:
So the SHV500v2 is 4s compatible and the HV500v2 is 3s compatible. Sent from my SM-N920V using Tapatalk |
Re: Have tech questions? Will answer. Quote:
Quote:
|
Re: Have tech questions? Will answer. Can I do 4S @4volt each cell(not 4.20) .. On BRXL with the limited edition "custom pro 13t".. It will be only on comps, so fearly short runs and full throttle will probably not happening often but just want to have the extra power/punch in back up.. Sent from my iPhone using Tapatalk |
Re: Have tech questions? Will answer. The AE2 survives 4s just fine. The BRXL just has a better BEC, IIRC. Be careful of stalling the motor, You can fry the comm in an instant if your not careful. |
Re: Have tech questions? Will answer. 4s is no problem. Have a first gen shv and sticking to 16v for that reason? |
Re: Have tech questions? Will answer. Quote:
|
Re: Have tech questions? Will answer. Quote:
Was this an answer to mine 4s question? [emoji106][emoji12] Sent from my iPhone using Tapatalk |
Re: Have tech questions? Will answer. Quote:
last weekish. The last batch of shv was also 4s safe. If you have any issues, you will get a v2 for warranty "thumbsup" |
Re: Have tech questions? Will answer. Quote:
Sounds good to me. Sorry for posting publicly. Should have contacted you directly. Emotions got the better of me :-) |
All times are GMT -6. The time now is 06:21 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com