|
| LinkBack | Thread Tools | Display Modes |
04-19-2018, 08:42 PM | #1 |
Newbie Join Date: Apr 2018 Location: Canada bc
Posts: 23
| Ax10 glitching after installing hw 1080?!?
I have a ax10 scorpion. Everything was stock except last week in put in this servo HITHS645MS - Super Torque MG Univ 0.20/133oz By HITEC @ Great Hobbies It all worked good. Today I installed a 1080 esc and now the truck is very glitchy. I read it might be caused by too much power feeding the servo? 6 v servo. My esc is set to 6v. Any help would be great |
Sponsored Links | |
04-19-2018, 09:20 PM | #2 |
Rock Crawler Join Date: Mar 2016 Location: Zagreb, Croatia
Posts: 747
| Re: Ax10 glitching after installing hw 1080?!?
The 1080 could probably feed 3 servos like that easily. How exactly is it glitchy?
|
04-20-2018, 07:42 AM | #3 |
Newbie Join Date: Apr 2018 Location: Canada bc
Posts: 23
| Re: Ax10 glitching after installing hw 1080?!?
It will move on its own at times. Never did this before. Steer or drive on its own. Also I don’t have a 2.4 receiver. It’s old school |
04-20-2018, 09:30 AM | #4 |
I wanna be Dave Join Date: Jun 2016 Location: Austin
Posts: 6,010
| Re: Ax10 glitching after installing hw 1080?!?
So, an AM radio, or an FM radio? Do you have a spare set of frequency crystals to change it over to and test it again? |
04-20-2018, 09:40 AM | #5 |
Rock Crawler Join Date: Mar 2016 Location: Zagreb, Croatia
Posts: 747
| Re: Ax10 glitching after installing hw 1080?!?
I guess you're experiencing some radio interference, maybe from the new ESC and/or motor. Just rearranging the wiring may help, but I'd suggest getting a 2.4GHz set. Good stuff can be had for under 50$.
|
04-20-2018, 10:06 AM | #6 |
I wanna be Dave Join Date: Jun 2016 Location: Austin
Posts: 6,010
| Re: Ax10 glitching after installing hw 1080?!?
Definitely, what Ninomaniac said... I'd get a FlySky GT3C - comes with a USB-rechargeable LiPo battery for the transmitter, 3-channels, 10-model memory (and more receivers are less than $8, so you can control your other RCs for CHEAP!):
|
04-20-2018, 10:17 AM | #7 |
Newbie Join Date: Apr 2018 Location: Canada bc
Posts: 23
| Re: Ax10 glitching after installing hw 1080?!?
Always my luck with mods.. get one but then I need more to keep the first one working. Damn
|
04-20-2018, 10:27 AM | #8 |
Moderator Join Date: Sep 2008 Location: PA
Posts: 13,935
| Re: Ax10 glitching after installing hw 1080?!? |
04-20-2018, 11:33 AM | #9 |
RCC Addict Join Date: Sep 2014 Location: Alberta
Posts: 1,116
| Re: Ax10 glitching after installing hw 1080?!?
Find yourself a stock Tactic 3 channel radio from an RTR Axial even (not the crappy Honcho style, though! Make sure its the 3 channel one). Solid little radio for what it is. The Spektrum DX2E that comes with the Vaterra Ascender is a good beginners unit too. Either should be had for $45 CAD.
|
04-20-2018, 12:56 PM | #10 |
Rock Crawler Join Date: May 2016 Location: SoWIs
Posts: 618
| Re: Ax10 glitching after installing hw 1080?!?
It could be your 1080's neutral range is set too narrow. If the radio is old, it's possible it's not centering that great. Check out setting 11, change it to a higher number and see if that helps. Also try unplugging the steering servo to see if that changes anything. It's unlikely but I have seen HiTec's cause issues with certain radios, but it's usually very high-tq afftecting Spektrums. https://cdn.shopify.com/s/files/1/01...rogramming.png You could also try changing #13, PWM freq. Certain motor frequencies from brushed motors can really affect FM/AM radios from EMI. Last edited by Hydrocarbon92; 04-20-2018 at 12:58 PM. |
04-20-2018, 07:21 PM | #11 |
Newbie Join Date: Apr 2018 Location: Canada bc
Posts: 23
| Re: Ax10 glitching after installing hw 1080?!?
Ok thanks for the info. I’ll try that for sure. A few of the options on the 1080 I don’t even k ow what they do.. yea it’s a older radio. It did work fine with the old esc and new servo.
|
04-21-2018, 02:05 AM | #12 |
RCC Addict Join Date: Feb 2016 Location: Santa Maria, CA
Posts: 1,751
| Re: Ax10 glitching after installing hw 1080?!?
Try mounting your receiver and ESC further apart from each other. AM/FM radios are more prone to interference than 2.4ghz, but just moving equipment to opposite ends of the car could make enough difference to eliminate your glitching... and it's free to try.
|
04-21-2018, 02:24 AM | #13 |
RCC Addict Join Date: Apr 2009 Location: LA
Posts: 1,662
| Re: Ax10 glitching after installing hw 1080?!?
Are your antennas (TX and RX) fully extended and pointed straight up?
|
04-21-2018, 09:44 AM | #14 |
Newbie Join Date: Apr 2018 Location: Canada bc
Posts: 23
| Re: Ax10 glitching after installing hw 1080?!?
The antenna on the truck is not. Don’t have a tube to hold it up.
|
04-21-2018, 12:15 PM | #15 |
I wanna be Dave Join Date: Jul 2009 Location: Rancho Relaxo. California. USA. Earth.
Posts: 3,292
| Re: Ax10 glitching after installing hw 1080?!?
Get a bec. Sent from my XT1650 using Tapatalk |
04-21-2018, 01:44 PM | #16 |
Rock Crawler Join Date: Mar 2016 Location: Zagreb, Croatia
Posts: 747
| Re: Ax10 glitching after installing hw 1080?!?
Why should he get a bec?
|
04-21-2018, 02:22 PM | #17 |
Quarry Creeper Join Date: Feb 2018 Location: East otis
Posts: 392
| Re: Ax10 glitching after installing hw 1080?!?
Wouldn't need a bec with that setup. 1080 has a strong internal bec Sent from my SAMSUNG-SM-G920A using Tapatalk |
04-21-2018, 10:07 PM | #18 |
Newbie Join Date: Apr 2018 Location: Canada bc
Posts: 23
| Re: Ax10 glitching after installing hw 1080?!?
Rebwored connections. Made a mount and put esc on the rear end. Turned my neutral passion on the esc up. Still does it at times. Looking for a used remote and receiver
|
04-21-2018, 11:52 PM | #19 |
RCC Addict Join Date: Apr 2009 Location: LA
Posts: 1,662
| Re: Ax10 glitching after installing hw 1080?!? |
Ax10 glitching after installing hw 1080?!? - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
my ax10 is glitching...any ideas? | mummyman | Axial AX-10 Scorpion | 17 | 01-23-2012 06:29 PM |
ax10 glitching issue....help? | mummyman | Electronics | 8 | 01-23-2012 06:26 PM |
Русские идут (the Russian is coming) - our ironworker goes Scale... | nicodrive01 | Scale Videos! | 8 | 05-07-2011 10:33 PM |
Installing AX10 Scorpion Universal Joints | shcuck | Axial SCX-10 | 3 | 04-23-2011 08:37 AM |
| |