Tactic tr325

[Doro]

Hello i run axial scx10.2. I have tactic tr325 receiver and tactic ttx200 controller. All of the sudden it stopped working... no throttle, no steering receiver doesnt blink, it makes only two beeps when powered on instead of three beeps. When trying to bind the controller again, it doesnt work. Reciever wasnt in contact with Water... Any ideas?

[DukeMinnix]

Originally Posted by Doro

Hello i run axial scx10.2. I have tactic tr325 receiver and tactic ttx200 controller. All of the sudden it stopped working... no throttle, no steering receiver doesnt blink, it makes only two beeps when powered on instead of three beeps. When trying to bind the controller again, it doesnt work. Reciever wasnt in contact with Water... Any ideas?

did you have the receiver unplugged and maybe intentionally reversed all the servo/esc cables? If not that, may have burnt up via too much power

[mikemcE]

Try recalibration not re binding.....


Hang up and Drive

[MasteroFlego]

Your ESC may be dead, what is it?

Sent from my SM-G960W using Tapatalk

[Doro]

Originally Posted by DukeMinnix

did you have the receiver unplugged and maybe intentionally reversed all the servo/esc cables? If not that, may have burnt up via too much power

Nope... I didnt mess with cables..

[Doro]

Originally Posted by mikemcE

Try recalibration not re binding.....


Hang up and Drive

Its self calibrating so i cant calibrate it manually.

[Doro]

Originally Posted by MasteroFlego

Your ESC may be dead, what is it?

Sent from my SM-G960W using Tapatalk

Why do u think esc? I thought its either controller or reciever...

[Steve g]

Esc powers the reciever. Try unplugging and replugging esc wire in reciever, may be it came loose.

Sent from my SAMSUNG-SM-G920A using Tapatalk

[Doro]

Originally Posted by Steve g

Esc powers the reciever. Try unplugging and replugging esc wire in reciever, may be it came loose.

Sent from my SAMSUNG-SM-G920A using Tapatalk

Wires Are good, reciever is powered because when trying to bind again it blinks... But the light doesnt stay on like its in the manual..

[mikemcE]

First Test the battery or replace it with a known fresh charged
Second are you running 3s, as you mentioned 3 beeps.
What ESC are you powering? is polarity correcton rx(brown wire is ground)
Channel 1 is to steering servo, channel 2 is for throttle. Make sure both brown?black wires are in the negative slot

[Steve g]

Is your transmitters throttle trim set in the middle?

Sent from my SAMSUNG-SM-G920A using Tapatalk

[Voodoobrew]

I have not had a ttx 200 only the ttx300. But when my receiver went out, it had a solid red light, no noises. The problem is probably not throttle trim, throttle trim issues I have not seen effect steering. I believe the 2 beeps you hear are coming from the ESC and not the receiver. the esc beeps according to the voltage not the receiver, as the receiver runs off a bec that is usually a lower voltage then 2s. Are there any lights on the receiver? cant find mine at the moment

[Doro]

I got it guys..... Problem is with the stock servo. As soon as i disconnect the driving servo throttle start working... I found some guys experiencing the same peoblem. After replacing servo the problem was solved..

[Natedog]

Originally Posted by Steve g

Esc powers the reciever. Try unplugging and replugging esc wire in reciever, may be it came loose.

Originally Posted by mikemcE

First Test the battery or replace it with a known fresh charged
Second are you running 3s, as you mentioned 3 beeps.
What ESC are you powering? is polarity correcton rx(brown wire is ground)
Channel 1 is to steering servo, channel 2 is for throttle. Make sure both brown?black wires are in the negative slot

Originally Posted by Steve g

Is your transmitters throttle trim set in the middle?

All good suggestions.

Originally Posted by Doro

I got it guys..... Problem is with the stock servo. As soon as i disconnect the driving servo throttle start working... I found some guys experiencing the same peoblem. After replacing servo the problem was solved..

Hahaaha, I was going to mention that lately a dead steering servo has been the cause of quite a few esc/rx problems from the threads I've read. Glad you got it sorted.