Go Back   RCCrawler Forums > RCCrawler General Tech > Electronics
Loading

Notices

Thread: What determines ESC starting speed?

Reply
 
LinkBack Thread Tools Display Modes
Old 08-14-2019, 10:09 AM   #1
Newbie
 
Join Date: Oct 2010
Location: oak ridge
Posts: 7
Default What determines ESC starting speed?

I have a need for an ESC (with or without BEC or brake) that has the lowest starting speed in forward and reverse. Most of the ESC's that i have start at hundreds and even thousands of rpms. I assume this depends on the motor load and other factors, so...

1. Are there any published data or tests on this subject?

2. What are your personal experiences or recommendations?

Any and all help appreciated.
butchalline is offline   Reply With Quote
Sponsored Links
Old 08-14-2019, 10:15 AM   #2
Moderator
 
JatoTheRipper's Avatar
 
Join Date: Sep 2008
Location: PA
Posts: 13,922
Default Re: What determines ESC starting speed?

I can't answer this, but I've wondered the same so I'll be watching this thread. Good post.
JatoTheRipper is offline   Reply With Quote
Old 08-14-2019, 10:41 AM   #3
I wanna be Dave
 
Join Date: Jun 2016
Location: Austin
Posts: 6,005
Default Re: What determines ESC starting speed?

From a completely uneducated standpoint, I can say my CC Mamba X ESC / Holmes Revolver 1800kv sensorless brushless motor combo will crawl at such a slow speed that I can watch the motor rotate incredibly slowly.

It's an outrunner, which means I can see the outside of the motor housing spin while driving my Bomber (which has no interior).

Here's someone's YouTube video where you can see what I mean:

https://www.youtube.com/watch?v=PNoPTKE6mCw

Last edited by durok; 08-14-2019 at 10:50 AM.
durok is offline   Reply With Quote
Old 08-14-2019, 11:42 AM   #4
RCC Addict
 
Join Date: Feb 2008
Location: Tekin, ID
Posts: 1,940
Default Re: What determines ESC starting speed?

Both motor and ESC can affect the lowest start RPM. The switching frequency of the ESC, the number of poles and slots in the motor, the strength of the motor magnets and the motors' internal resistance all play a part.

As far as published data on ESC start RPMS, I have never seen anything before.
Ty@Tekin is offline   Reply With Quote
Old 08-14-2019, 12:15 PM   #5
I wanna be Dave
 
Join Date: Jun 2016
Location: Austin
Posts: 6,005
Default Re: What determines ESC starting speed?

Quote:
Originally Posted by Ty@Tekin View Post
Both motor and ESC can affect the lowest start RPM. The switching frequency of the ESC, the number of poles and slots in the motor, the strength of the motor magnets and the motors' internal resistance all play a part.

As far as published data on ESC start RPMS, I have never seen anything before.
I will state here that the Holmes Revolver has a 14 pole 12 slot stator, which has got to contribute to the high torque and fine low-speed control of the combo...
durok is offline   Reply With Quote
Old 08-14-2019, 12:20 PM   #6
I wanna be Dave
 
Join Date: Jul 2005
Location: North Idaho
Posts: 3,647
Default Re: What determines ESC starting speed?

What kind of load are you going to have on the motor when it starts?
Greatscott is offline   Reply With Quote
Old 08-14-2019, 12:34 PM   #7
Newbie
 
Join Date: Oct 2010
Location: oak ridge
Posts: 7
Default Re: What determines ESC starting speed?

Greatscott: The load would be virtually zero. It will be used on a boat, so the starting load would be only the inertia of the motor, shaft and prop. And the motor would be brushed with gearbox reduction to 550 RPM max.
butchalline is offline   Reply With Quote
Old 08-22-2019, 09:28 AM   #8
Rock Stacker
 
Join Date: Mar 2019
Location: Canada
Posts: 60
Default Re: What determines ESC starting speed?

With a brushed motor it's really just friction that is holding you back. If you start applying linear power from 0 volts nothing will happens until the motor produces enough torque to overcome it's resting friction. By then it is getting enough power to spin at hundreds of rpms once it's not 'stuck' . With a load it's the same thing really. Although a loaded down motor will not spin up as fast once friction is broken. Higher kv motors will spin much faster after the friction is broken and will require a higher power level to get the same torque to get going.
Some ESC manufacturers have a minimum power level on startup but with brushed motors it is not necessary.
You can normally reduce speed once it's spinning.

For brushless motors it's a whole other can of worms why they need a minimum rpm. That is to create enough back emf to determine the position of the rotor.
Alka is offline   Reply With Quote
Old 08-29-2019, 10:04 AM   #9
owner, Holmes Hobbies LLC
 
JohnRobHolmes's Avatar
 
Join Date: Nov 2004
Location: Volt up! Gear down!
Posts: 20,290
Default Re: What determines ESC starting speed?

On a brushed motor, we are looking at an interaction between the motor detent force, and the minimum PWM of the ESC. In almost all cases, rough startup is just low quality ESC design. Once we get a "nice" ESC with lots of low end PWM granularity, then we can begin refining motors for better startup.


The hobbywing 1080 (all china made) is a good budget choice with decent startup. My BRXL (higher cost, all USA manufacturing) has a much lower minimum PWM and also has throttle curves which smooth out the low end control further. If you are using a RTR style ESC, replacing your ESC is probably a good first choice to get better low speed control.
JohnRobHolmes is offline   Reply With Quote
Reply

Tags
esc, minimum, starting speed



What determines ESC starting speed? - Similar Threads
Thread Thread Starter Forum Replies Last Post
Tekin RS Gen2 esc starting point Help desertdude Electronics 11 02-27-2016 05:12 PM
ESC and slow speed operation - which ESC? MeanTT Electronics 4 10-17-2015 08:53 PM
New esc/speed controller ski doo boy Losi Mini-Rock Crawler 18 03-05-2011 12:38 PM
What determines the gender of a plug? Thorsteenster Electronics 9 03-19-2008 07:02 AM
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -6. The time now is 07:15 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com