|
| LinkBack | Thread Tools | Display Modes |
01-13-2021, 10:15 AM | #1 |
Pebble Pounder Join Date: Mar 2010 Location: Danbury
Posts: 134
| SR6200a AUX1 issue maybe, AVC interference?
Hello all, I recently acquired a Axial SCX 10.3 kit, using Tekin ESC, Tekin Motor, Savox servo, Mytrick attack light kit, both dig and two speed Spectrum servos and the TX/receiver is DX5 rugged, and a Spektrum SR6200a. I have everything setup except the lights. I am trying to get the Mytrick setup on AUX1 on the G button. I have everything wired right on the MYtrick, but cannot get it to work right. My only thought is the AVC system works off of AUX1 channel, I am assuming its causing some issue with the lighting. So I am trying to turn off the AVC. The manual is vague about the sequence to deactivate the AVC. It states to turn the power on to the receiver then hit the bind button 3 times in 1.5 seconds. I have been trying that all morning, with no luck. It claims you get a 3-flash on the LED on the unit. I have tried rebinding the TX/RX and tried this 3 button press at various times, to no luck. I have tried calling Horizon, but its a long wait and I have to work today, so cant pull that off, any chance someone could provide some advice on shutting off the AVC on this particular unit? Thanks for the help! Take care, |
Sponsored Links | |
01-13-2021, 10:38 AM | #2 |
Rock Crawler Join Date: Jan 2019 Location: Calgary
Posts: 566
| Re: SR6200a AUX1 issue maybe, AVC interference?
Did you try both steps? You only listed step one of disabling AVC. It does use channels 1 and 2, did you try your lights in channel 3 to make sure they work?
|
01-13-2021, 11:02 AM | #3 |
Pebble Pounder Join Date: Mar 2010 Location: Danbury
Posts: 134
| Re: SR6200a AUX1 issue maybe, AVC interference?
I need to try this tonight on aux3. I can operate the lights from the mode switch tho, just not from the radio.
|
01-14-2021, 04:32 AM | #4 |
Pebble Pounder Join Date: Mar 2010 Location: Danbury
Posts: 134
| Re: SR6200a AUX1 issue maybe, AVC interference?
Went and picked up an sr515 tonight. Still no action. Going to contact trickrc again. Maybe it's a bad dg-1 module??? Very strange.
|
01-14-2021, 01:21 PM | #5 |
I wanna be Dave Join Date: Feb 2017 Location: My mothers basement
Posts: 2,128
| Re: SR6200a AUX1 issue maybe, AVC interference?
for the mytric light set them up as momentary:active button. it is not an on off switch. it should work fine on aux1, if not avc would shut off not the lights. first click: turn on running lights second running and low thirs, running and med fourth running and high beams 5th off something like that Last edited by Voodoobrew; 01-14-2021 at 01:25 PM. |
SR6200a AUX1 issue maybe, AVC interference? - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
DX5R aux1 | Levi | Electronics | 1 | 05-07-2018 12:13 PM |
Dx5c with avc | DKOR | Electronics | 14 | 04-06-2018 12:20 PM |
Has anybody used the spektrum AVC | djjerbeck | Electronics | 26 | 01-08-2016 04:03 PM |
Yeti XL with Spektrum AVC | Gso125 | Axial Yeti XL | 10 | 12-16-2014 08:51 PM |
Thread Tools | |
Display Modes | |
| |