|
| LinkBack | Thread Tools | Display Modes |
06-24-2021, 08:19 PM | #1 |
Newbie Join Date: Apr 2016 Location: Spaced Out
Posts: 8
| Sanity check my upgrade plan
I have an old Wraith 2.2 that's been dead in a closet for 4-5 years and I recently got working again. I was still on the stock electronics but I had worked through replacing a lot of the linkage and suspension with metal, by way of breaking something plastic every single time I took it out. As I was about to buy new NiMH batteries I thought "lets convert to lipo" which has led into a plan to revamp most of the stock electronics it has. What do I want out of it? I'm into this theoretically for rock crawling but in practice it's comparatively rare that I put it on rocks and more trail bashing actually happens, so I want low speed control, but I also would have a lot of fun if I could make this thing quick. I want to be able to drive it through tire-deep water without being scared about it (since that killed it last time). First I need a new ESC that can handle >2s lipo. I am eyeing the Holmes BR-XL for low speed control. I also want to upgrade my stock servo to one with atleast 300oz of torque. The BR-XL has a 5A BEC, but a 300oz servo is said to be right in the vague inflection point where an external BEC may be needed. I decided to just go ahead and get one and be done with it, and I'm looking at the CC 15A waterproof BEC. Then I thought, well if I'll have this beefier external BEC anyway might as well get a more OP servo, and I'm looking at a waterproof savox .11/500oz @ 7.4v (which stalls at ~8amps). Since the ESC can handle up to 6s, and with this CC BEC, I think I want to try out 4s lipo in hopes of making it fly, and I'm looking at a 2pack of 4s 6500mah LiPos. Part list ESC - BR-XL Waterproof - https://www.rpphobby.com/product_p/hh-210100002.htm BEC - BEC 15A Waterproof - https://www.rpphobby.com/product_p/cse010-0153-00.htm Servo - Servo 0.11 sec / 500oz @ 7.4V Waterproof - https://www.savoxusa.com/collections...ta#spare-parts Batteries - 14.8V Lipo 4S 6500mAh 60C - https://www.amazon.com/dp/B07PD2CNQM/ Plan I know some dont, but I like a power switch, so I want to put my own SPST cutoff switch on the positive lead to the battery for turning ESC and BEC on and off together. I'm thinking of running the servo off the CC BEC, but running the receiver off the internal BEC of the ESC, since it's low current. That way I can run the servo at high voltage (when I want to) and not overvolt the receiver. For now I'm probably sticking with the traxxas 21T brushed motor I have since I just bought that. I'm also probably going to stick with the stock gears/transmission, until I break them (the way this goes that will prob be soon anyway, running out of other things to break). I don't think I really need 500oz of torque, but I thought maybe undervolting an over-powered servo (at 6V or even 5.25V compared to it's only advertising stats at 7.4v) would be better reliability wise, if the torque will just scale down linearly with the voltage. Also I like the idea of being able to adjust the CC BEC voltage to change this when I want to. Questions Does this setup make sense to run on 4s? Will I be able to tune the ESC with stock gears to have good lowspeed control and also the speed to fly off jumps at full throttle? Or is that an impossible contradiction? Is it safe to undervolt the servo advertized at 7.4v to 6v or even 5.25v? Asking in case my assumption I can just scale down the torque with lower voltage is somehow naive. Is there anything grossly mismatched here? Thanks |
Sponsored Links | |
06-24-2021, 10:59 PM | #2 |
Quarry Creeper Join Date: Nov 2006 Location: Lexington Park
Posts: 420
| Re: Sanity check my upgrade plan
I dont think that 21t motor will last more than a battery pack at 4s, especially if you run a whole 6500mah at one time. I would go brushless after that motor is toast. The holmes puller pro v2 on like 2800kv would be awesome on 4s. I run all my rigs on 4s with direct power 4s capable servos and eliminate the need for a bec. Its just much simpler and you get tons of torque. The holmes servos or the g13/14 from 3brothers would work great for that. Also id go brushless if you want to play in water and have long trail rides, they just take more abuse and survive water so much better. If you want to stay brushed try a holmes trailmaster sport 5 slot. They are cheap throw away motors but preform amazing for the price and on trails Sent from my SM-G965U using Tapatalk |
06-25-2021, 12:06 AM | #3 |
Rock Crawler Join Date: Mar 2016 Location: Zagreb, Croatia
Posts: 747
| Re: Sanity check my upgrade plan
Oof... a 2.2 Wraith will need a lot of upgrades for what you want out of it. I had one and the plastic gears in the tranny, plastic lockers, cheap metal diff gears, it all got wrecked. Only thing that can take some power are WB8 axles and front CVDs (mine was a Spawn kit, maybe you'll have to upgrade those too). Servo torque and speed scales with voltage, you're right. You'll have to shave off a piece of a link mount on the skid to install a 550 motor or add spacers to raise the tranny. I did the former. But a brushed system in a Wraith that'll go fast will make your motors *very* expendable. Go brushless, esp since you don't seem to be on a tight budget Oh, and there's a reason you've never seen a switch wired from ESC to battery - it'll have to be a huge switch. Don't think you'll find a switch that can take say 50+ amps and doesn't weigh more than the rest of your electronics! It's good practice to unplug your battery after running anyway. |
06-25-2021, 05:34 AM | #4 | |
Rock Crawler Join Date: Feb 2020 Location: Fort Leonard Wood
Posts: 868
| Re: Sanity check my upgrade plan Quote:
To simplify things I would go direct power servo. This way you don't have to worry about an internal or external BEC. The ESC you mention above is brushed only. There are great bushed motors but when I hear trailing and bashing it seems to me that brushless may be a better choice, but that is just my thoughts. I had a $50 3Bros G11 that out performed my 500 0z 1230 Savox (using an external BEC so it had all the amps it needed). I have had a few Savox servos and they are never as powerful as other servo I have had that claim to even have less power. As I used the Savox servos I experienced power and speed fade. I have had a couple 1212s get stiff one died and the other still moves but has lost power an speed. Under volting or under amping wont hurt the servo, it just won't work as well. I have a MambaX that I like. If you do want to go with a BEC/ESC powered servo it does have a legit internal BEC that is programable and it can put out all the voltage and amperage (up to 8 amps I think). It is waterproof and can handle up to 6s I believe. The MambaX is great but bigger and more expensive than other ESC. Space shouldn't be a problem in a Wraith. Not sure about you budget? I have an older Wraith 2.2. I had the MambaX with a Trailpro Holmes Hobbie 3800 sensored motor and it was fast and fun but not the best motor for crawling but the old Wraith 2.2 really aren't that good for crawling anyway. Ihad a Savox 1212 in that lasted a short period of time before it became stiff and useless. I but the MambaX in another rig and the Wriath and the Trailpro just sit on a shelf with a worthless Savox servo. It seems that allot of people like the Holmes Hobbie Puller pros for trailing / crawling. I have never tried one. I just crawl. The motors I have I like are my Revolvers, My Tenkin HD brushed and my Tenkin ROC. I have some HH sports and they are fine but don't have as much low end torque and not the best drag brake but if you are looking for inexpensive, at $15-20 they are the deal. Last edited by MOguy; 06-25-2021 at 05:52 AM. | |
06-25-2021, 06:33 AM | #5 |
RCC Addict Join Date: Jan 2019 Location: Corvallis, OR
Posts: 1,561
| Re: Sanity check my upgrade plan
Considering the path you’re going down, skip the brxl and bec, and just get a mamba x. It’s 6s capable, has a beefy bec, can be used brushed or brushless, and you could use it with the stock motor until it quits. At that point a puller pro is probably going to be one of the best options for all around power/torque, low speed control and high speed buffoonery. Sent from my iPhone using Tapatalk |
06-25-2021, 09:34 AM | #6 |
Rock Crawler Join Date: Mar 2021 Location: Santa Barbara
Posts: 659
| Re: Sanity check my upgrade plan
I’m doing a flat rail chassis wraith build. The electronics I got were: Mamba x Castle 2850kv slate motor 370tbl protek servo 4s 5200 tattu batteries If I didn’t get a great deal on that servo, I would have looked more into direct power servos. |
06-25-2021, 09:51 AM | #7 |
Rock Crawler Join Date: Feb 2020 Location: Fort Leonard Wood
Posts: 868
| Re: Sanity check my upgrade plan With the MambaX you can set the volts up and it will deliver the needed amps and it should work great. Make sure your receiver can handle the added power voltage.
Last edited by MOguy; 06-25-2021 at 09:55 AM. |
06-25-2021, 10:14 AM | #8 |
I wanna be Dave Join Date: Feb 2017 Location: My mothers basement
Posts: 2,128
| Re: Sanity check my upgrade plan
$20 brushed motors are great for water and on 4s they have some power. They might not last as long but you should get a few runs. mostly the brushes just wear faster. If it burns up then you are geared too high. People run their ride on power wheels with these motors at 24v all the time. The brushed motors won't handle the wide rage of speeds as well as brushless motors though. Brushless motors can get wet inside and rust just like brushed motors but are more expensive to replace. For water I only recommend cheap brushed motors. Water can kill any electronics, there is always a risk. So my advice is keep it inexpensive if water is expected. |
06-25-2021, 12:05 PM | #9 |
Rock Crawler Join Date: Mar 2021 Location: Santa Barbara
Posts: 659
| Re: Sanity check my upgrade plan It will be a standard spektrum 3 channel. I don’t know the specs on it, but I’ve been using the 5 channel equivalent in my UMG10 at 7.4v with a 170tbl with no issues.
|
06-25-2021, 12:16 PM | #10 |
Rock Crawler Join Date: Feb 2020 Location: Fort Leonard Wood
Posts: 868
| Re: Sanity check my upgrade plan I have had a few Spektrums and I think they will be fine at 7.4. (I think 7.5 on the MambaX)
Last edited by MOguy; 06-26-2021 at 05:33 PM. |
06-25-2021, 03:12 PM | #11 |
I wanna be Dave Join Date: Feb 2017 Location: My mothers basement
Posts: 2,128
| Re: Sanity check my upgrade plan
Spektrum receivers are good to 9.6v
|
06-25-2021, 11:24 PM | #12 | |
Newbie Join Date: Apr 2016 Location: Spaced Out
Posts: 8
| Re: Sanity check my upgrade plan Quote:
Other than that, thanks for all the responses. A lot of really good perspective and info. My main takeaways are 1. Brushless would mostly be better for my usage 2. Servos exist that can run on 4s worth of voltage directly 3. Speed controllers exist which can handle brushed AND brushless motors (I did not know that!) 4. The mamba x is a crowd favorite 5. Savox servos are not a crowd favorite. I don't know why i thought they were like the name brand but that's not the first time I've heard someone say they lose power and wear out fast. I just got the 21T motor a week ago to save the crawler from the closet and barely put 2 packs through it, so I didn't want to immediatly get rid of it. But otoh buying a $100 brushed speed controller to save a $25 motor is probably not wise. I also was worried about losing fine speed resolution at the low end with brushless but with more research it seems this is less of an issue with newer sensored ones. Now that I know I can get an ESC that can handle both motor types, that's a no brainer to me. I can have fun wrecking this 21T motor while letting my wallet cool off, and then go for a hefty brushless. I'll just have to be disciplined about maintenance after water (bearings etc) since it's not exactly disposable. Or heck just swap on a cheapo brushed motor if I want to submarine. But the mamba X is the same price as the BRXL+BEC, and to have less things to break under the hood, more capability, and the option to use either motor type... no brainer. Only drawback is I'm not thrilled about having to run fans, but I'll get over it. | |
06-25-2021, 11:43 PM | #13 | |
Newbie Join Date: Apr 2016 Location: Spaced Out
Posts: 8
| Re: Sanity check my upgrade plan Quote:
Funny you say that about there being plenty of space in the wraith, I don't have much experience to compare but my perception is the opposite. I do keep the interior in it and I guess that hugely reduces the available area. It seems like the remaining area in the front and back of the cage is pretty limited. I expect to have to do some problem solving to fit things. I'll probably move the battery to the front for weight, and put the ESC in the back, which will get it a little higher to protect the fan from getting wet as much. Interesting. What about them makes them not great for crawling? Stock weight distribution or something else? | |
06-26-2021, 05:19 AM | #14 |
Rock Crawler Join Date: Mar 2016 Location: Zagreb, Croatia
Posts: 747
| Re: Sanity check my upgrade plan
Yeah, you'll have to do a lot of Tetris with electronics in a Wraith. Now that I think about it, I barely managed to get a 5000 3s under the hood (sideways). A 4s 6500 may fit in the back but the whole thing will handle like crap! ESC can go in the front where the stock Rx box/faux motor goes. |
06-26-2021, 06:20 AM | #15 |
Quarry Creeper Join Date: Feb 2018 Location: East otis
Posts: 392
| Re: Sanity check my upgrade plan
I have a few crazy wraiths. I also run 4s, but small hv packs. They fit perfectly where the rx box sits up front. The bigger the battery, the heavier it is, and the more broken parts you will end up with. I started off with large packs, and one day bought a small drone battery on sale for like 11 bucks. Made such a big difference in both crawling and higher speed handling that I bought 11 more. I get up to an hour crawling, about 45 minutes trailing, and 20 minutes geared up snow bashing out of a 1600 mah hv pack. The thing is with these, on higher voltages, you'll dump alot of money into to make it last a battery pack. There's not a single moving part left stock on all of ours, everything had to be replaced with high end parts. Honestly probably have over a grand in each. Problem is, not many quality aftermarket parts available anymore. Vanquish and Dlux and everyone else gave up on these a couple years ago. Sent from my SM-G970U using Tapatalk |
06-26-2021, 09:34 AM | #16 |
I wanna be Dave Join Date: Feb 2017 Location: My mothers basement
Posts: 2,128
| Re: Sanity check my upgrade plan
instead of a switch you can make a plug that when disconnected interrupts one of the battery leads. then carve out a scale accessory and glue it in there, to make a Deadman's switch. just pull the scale accessory off the disconnect the battery.
|
06-26-2021, 05:43 PM | #17 | |
Rock Crawler Join Date: Feb 2020 Location: Fort Leonard Wood
Posts: 868
| Re: Sanity check my upgrade plan Quote:
The big wraith is big and awkward I think it big chassis tube thing gets in the way if it suspension working. I also don't think the Capra is all that great either, it seems to want o always raise a wheel but that could probably be fixed. I but my esc up in the interior behind the seats, double sided tape and zip tie. There is also room u front under the hood, depending on the size of the battery you run if you run it up front. | |
06-27-2021, 04:16 PM | #18 | ||
Newbie Join Date: Apr 2016 Location: Spaced Out
Posts: 8
| Re: Sanity check my upgrade plan Quote:
Quote:
At first I thought everything had to say COMPATIBLE WITH X on it and came around to realize a lot of stuff are interchangeable. What parts are "proprietary" to a certain rig type, or only compatible with specific other rigs? Is it most things other than the electronics? I'm kinda lost with the KV. I know endless has been written about this, and I've read/watched a lot and get the theory but have nothing to anchor the numbers to. I know I can't have perfect crawling and huge speed. Speed is fun, but I really enjoy smooth slow movement. I'd sacrifice some speed for smoothness while doing mild crawling (going up and down street curbs, smooth slow hill climbing, watching articulation p0rn while driving over my foot nice and slow, etc). I guess I want something kinda in the middle. After reading about this I'm more apt to pick something in the lower kv range like 2200 (atleast i think that's "low"?) but I'm not sure. Should I basically just pick something, and then try it out, and adjust the transmission/throttle curve until I like it? | ||
06-27-2021, 04:24 PM | #19 | |
Quarry Creeper Join Date: Jul 2020 Location: US
Posts: 232
| Re: Sanity check my upgrade plan Quote:
Read-Up! Mod-On! Crawl EXCESSIVELY! | |
06-27-2021, 04:27 PM | #20 | |
Quarry Creeper Join Date: Jul 2020 Location: US
Posts: 232
| Re: Sanity check my upgrade plan Quote:
Read-Up! Mod-On! Crawl EXCESSIVELY! | |
Tags |
battery, bec, esc, servo, upgrades |
Sanity check my upgrade plan - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Sanity Check | TheDirtyDiode | Traxxas Crawlers | 8 | 05-07-2020 09:21 AM |
Sanity check: SCX10 Honcho rear articulation? | Cr00zah | Axial SCX-10 | 11 | 03-11-2014 02:22 PM |
Newbie build, need sanity check | cyrusd | Newbie General | 7 | 04-26-2011 08:49 PM |
Sanity Check - 2 FXR, 4WS, Bullies, Punk Computer | honyock | Newbie General | 0 | 10-11-2009 01:50 PM |
Check my plan for power? | Willy | Electronics | 9 | 01-23-2009 09:48 PM |
| |