A decent winch controller?

[SleptOver]

Anyone know of a decent one?


I have a KYX dual motor winch, it's rated at 10 KG pulling power at 9v, and I can attest to it being crazy strong on a 2s lipo.


Problem I seem to be having is that the winch controllers that are (on paper) rated at 3s/11v pretty much instantly burn up if actually connected directly to a 3s lipo.. :P



The latest one I am about to try is this one: https://www.ebay.com/itm/314092789385


Though I don't like the remote, or the plethora of wires. So I'll probably remove the plug, and directly solder the wires I do need to the board.


My prediction however, is that it will fail the second it gets 11.1v.


This: https://www.ebay.com/itm/133045465655


Was the latest victim.. It died about 3 seconds after being connected to 3s. The poor thing lit is LED and a component let out the magic smoke.


So, the alternatives that so far works are:



1. Run it off the BEC/Receiver - Weak, and not sure the BEC likes it.


2. Run it off a dedicated 2s lipo - I don't really want to have a second lipo just for the winch, even though it works quite well and it lifts the TRX-4 clean off the floor without issues.


Suggestions?

[ferp420]

just run a small esc and call it a day if its too big take the case and heat sink off and heat shrink it and bam you just got a winch controler

be sure to pull the red wire from the plug that goes in to the reciver or you will have another smoke show

[heyok]

Come on! I make winch controllers. They work great!
Lots of versions to choose from here:
https://www.heyokperformance.com/Win...3_1588136.aspx

Any questions, please ask.

[ben h]

hey0k makes great ones iv had a few of his only downfall there costly compairec to a cheap brushless esc. but the esc dont hold like the hey0k controlers do. but if not winching in comp there great!

[SleptOver]

Originally Posted by heyok

Come on! I make winch controllers. They work great!
Lots of versions to choose from here:
https://www.heyokperformance.com/Win...3_1588136.aspx

Any questions, please ask.

Oh Nice, I think I'll do that one come next paycheck.

I'd like JST plug on both sides really, female on the input and male on the output, that would be plug and play :P

[heyok]

Originally Posted by SleptOver

Oh Nice, I think I'll do that one come next paycheck.

I'd like JST plug on both sides really, female on the input and male on the output, that would be plug and play :P

I'm happy to build it that way, just be sure to contact me before you place your order.

Thanks,
Al

[tigris99]

The rc4wd works perfect on 3s direct wire. I've had my rig that way for months and winch used to pull my heavy ass knightrunner a couple dozen times.

Sent from my SM-S906U using Tapatalk

[SleptOver]

Originally Posted by heyok

I'm happy to build it that way, just be sure to contact me before you place your order.

Thanks,
Al

Sounds awesome Will do.



You do international shipping I hope?

[KMS]

Hands down Heyok makes a great winch controller .I have used many of them no smoke have a great holding brake .He also has the wireless controller .his stuff top quality ..

[Greatscott]

Originally Posted by KMS

Hands down Heyok makes a great winch controller .I have used many of them no smoke have a great holding brake .He also has the wireless controller .his stuff top quality ..

I have a couple of things from Hey'OK, and I cannot recommend his wears enough. His stuff just works, and it is reliable.

But, sadly, a winch controller is not something that I have bought from him, but I am sure they are great, and well worth the money. On my rigs, I use HW1060 ESCs for winch controllers, they have more than enough power and will run on 3S.

[SleptOver]

Originally Posted by heyok

I'm happy to build it that way, just be sure to contact me before you place your order.

Thanks,
Al

How exactly do you want me to contact you, I am ready to place the order


I figure I add two connectors for the extra 4$

[high plains drifter]

Originally Posted by SleptOver

How exactly do you want me to contact you, I am ready to place the order


I figure I add two connectors for the extra 4$

From his Heyok Performance page:

How to contact me:
While the web page does offer a way to send me a message, it does work, but it is difficult for me to reply to you.
Instead, please just send me an email. Send it to:

mostlyal@gmail.com

[SleptOver]

Well, all is good, order was made and paid for

thanx for the advice guys.

[heyok]

Hi Guys. Sorry for the late reply. The forum no longer sends me notifications when someone replies to a thread. I just looked now and see that I missed some important stuff, but it all worked out!

International Shipping: Yes I do!
Contact me: Through my web store works but as was mentioned, best is my email address: mostlyal@gmail.com

Cheers,
Al

[SleptOver]

Originally Posted by heyok

Hi Guys. Sorry for the late reply. The forum no longer sends me notifications when someone replies to a thread. I just looked now and see that I missed some important stuff, but it all worked out!

International Shipping: Yes I do!
Contact me: Through my web store works but as was mentioned, best is my email address: mostlyal@gmail.com

Cheers,
Al

Yup, it arrived today, and it works great!

Hm.... I love the smell of liquid insulation tape in the morning :P

JST plugs where, despite precautions taken on Al's part, opposite, but took me like 2 min to change em out as I do have new plugs on hand. No worries :P


It's insanely strong, can easily lift the entire truck vertically.


Awesomesauce.