|
| LinkBack | Thread Tools | Display Modes |
01-07-2023, 07:58 PM | #1 |
Newbie Join Date: Nov 2013 Location: Mulberry Grove IL
Posts: 25
| Flysky GT3B and a Winch Need Help
I have a hacked GT3B, a RC4WD winch and their wired winch controller. I have it hooked to channel 4 on my receiver and set to work of the D/R switch. I have it set for momentary control. My problem is it works fine going out. Press the button forward towards front off control and winch spools out. Problem is spooling in. First off it will just start spooling in on its own. I can press the switch towards the spool out position and it stops but soon after starts spooling in again. Also, the momentary in doesn't work. If I press the switch to spool in it runs non stop until I press the switch the opposite direction towards spool out. I'm not real up on this stuff yet, but I've been though all the settings I can find and can't figure it out. Anyone have any ideas? Thank you. This is the controller I'm using https://store.rc4wd.com/RC4WD-Wired-...it_p_3725.html |
Sponsored Links | |
01-10-2023, 02:23 AM | #2 |
Pebble Pounder Join Date: Aug 2020
Posts: 134
| Re: Flysky GT3B and a Winch Need Help https://www.heyokperformance.com/Win...3_1588136.aspx Check here first if you’re considering a new controller. Sent from my iPhone using Tapatalk |
01-10-2023, 08:24 AM | #3 | |
Newbie Join Date: Nov 2013 Location: Mulberry Grove IL
Posts: 25
| Re: Flysky GT3B and a Winch Need Help Quote:
Sent from my Pixel 6 Pro using Tapatalk | |
01-10-2023, 09:16 AM | #4 |
I wanna be Dave Join Date: Jan 2016 Location: california under the rock im crawling on
Posts: 4,259
| Re: Flysky GT3B and a Winch Need Help
it sounds like a radio problem i would go back and reset the buttons and try again ive had issues with some escs the nutral settings seem to migrate so i have to adjust the throtle trim it seems to do it more after running slot of different rigs some times if i turn everything off and back on a few times it fixes its self the gt3b and Cs are gletting old they ware out and at best need to be recalabrated every now and again your winch controler is basicly a cheap esc and most likely has its own calibration proccess its possable a new winch controler will work better with that radio but really there is no way to know i would remap the button and calibrate the radio and see if it dose anything also try a different button see if that helps some times alittle wd40 helps too ive had the buttons get sticky too |
01-10-2023, 09:08 PM | #5 | |
Pebble Pounder Join Date: Aug 2020
Posts: 134
| Re: Flysky GT3B and a Winch Need Help Quote:
I asked about winch controllers here a while back and everyone told me to stay away from the rc4wd one and get that heyok controller. It’s what I’m running and it works well, no creep. Just a suggestion, I’m sure lots of people are happy with the same one you’re using. Sent from my iPhone using Tapatalk | |
Flysky GT3B and a Winch Need Help - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Flysky GT3B and servo winch | Deerhurst | Electronics | 6 | 03-14-2018 04:18 PM |
Flysky fs gt3b | J21 | Newbie General | 3 | 06-04-2016 11:31 AM |
flysky gt3b | EMUTT | Electronics | 14 | 09-07-2011 11:13 AM |
Thread Tools | |
Display Modes | |
| |