Sloski's simple berg build I don't really need another Berg.......:shock: But I had these Awesome Delrin cases laying around.......:ror: and they were crying out " build me with a set of RCbros tubes"... im like WOW yea lets DO IT.......... so a pm to Will at RCbros, and a few days later I have some Awesome tubes to bolt up to my cases........."thumbsup""thumbsup" Thank you Will... parts list for now: My cases and RCbros tubes of course....."thumbsup""thumbsup" Gears not sure, as I have new stock gears with new Mann gears or I have RC4WD gears, Been running some in my current truck..... Or I could pull a few Frankiln's out of the mattress to get some RCbros gears .....:lmao:... not sure yet..... super 300's.........:ror:;-) knuckles and C's....?? Shocks............?? Hpi super star wheels for now.......... 14.4 grams...:shock::ror: tires................?? Chassis... CDW RT................;-) picture of the start.......... https://fdlbwa-dm2305.files.1drv.com...&cropmode=none I spent hours trying to get my link mounts set exactly right and still got them off a bit.....:x:x:cry: comments welcome....... thanx for lookin.......... |
Re: Sloski's simple berg build RCBro gears FTW. Although kinda goes agenst the whole keepin' it simple plan. But........ |
Re: Sloski's simple berg build :lmao: LOL.... the cases and tubes go against keeping it simple...... I could do stock cases and tubes, but what fun is that?........ |
Re: Sloski's simple berg build Well since my cases on the tube boss have a radius where it meets the case, you have to put a small bevel on the inside diameter of the tube to fit nice and tight....... not a great picture, but I think you can tell that it does not have a sharp edge any more........ https://ftj2nq-dm2305.files.1drv.com...&cropmode=none |
Re: Sloski's simple berg build Busting out the bling, good to see some OG 300's |
Re: Sloski's simple berg build Quote:
they are an older set with little use....."thumbsup" |
Re: Sloski's simple berg build Or Dlux knucks with the wraith C's? |
Re: Sloski's simple berg build Keep it simple with a micro switch dig. Lookin good Mike. |
Re: Sloski's simple berg build Quote:
LOL....I was thinking just one ESC...:shock: Thanx Doug..... Link mounts were a PIA...... used a 6mm BH screw and still had to use a small washer to keep it from dragging on the axles https://etj2nq-dm2305.files.1drv.com...&cropmode=none |
Re: Sloski's simple berg build Couldn't you just shorten the screw? Plus your hardware doesn't match. Chump would not approve! |
Re: Sloski's simple berg build Quote:
and that hardware is just for mock up, it gets tossed into a bag and I use new ones to put it back together........ Maybe the finished product he would........;-) |
Re: Sloski's simple berg build I have 5mm here, I may have acciently tossed 6mm in yours.. |
Re: Sloski's simple berg build Didn't factor in rusting. Come to think of it Chump probably wouldn't approve of shortening hardware anyways. Carry on... |
Re: Sloski's simple berg build Quote:
:lmao: that's too funny......"thumbsup" here they all match.... https://ezlbwa-dm2305.files.1drv.com...&cropmode=none https://etlbwa-dm2305.files.1drv.com...&cropmode=none and squared up the upper link mount where the front mounting hole is to make sure my servo has enough room..... also you have to really round off the back lower corner so the motor clears........ |
Re: Sloski's simple berg build Front axle mocked up with plastic XR C's and scx 8* knuckles.... the front 2 holes on the knuckles will most likely get cut off and new ones drilles and tapped......... still waiting on my VP C's.....:roll::roll::x https://gdlbwa-dm2305.files.1drv.com...&cropmode=none https://fjlbwa-dm2305.files.1drv.com...&cropmode=none |
Re: Sloski's simple berg build Did you file the plastic Cs to fit the knucs? I figured out how I can hold the Cs for milling. |
Re: Sloski's simple berg build No I didn't file them... I did them in my millpress........:shock::lmao: one came out great, the other, I almost threw it in the garbage.......:shock::x Awesome ...........they just need to get off back order....:x hope to have them by the next comp so I can just hand them over to you.....:ror: |
Re: Sloski's simple berg build Ok so I could not wait for the XR C's to get off back order..:evil: so I picked up some SCX C's to go with my knuckles....... had to whittle off ALL of the spline off the tubes to fit the C"s.....:shock: also got a bit more done on mock up..... https://fdiy8q-dm2305.files.1drv.com...&cropmode=none C's will get held on by 2 4mm set screws, one with the pin on it , gets a hole in the tube to keep it from ever turning on the tube , the other will just keep it in place........... Oh, and link mounts are in a far different place than im use too...:shock: might need a few RC bro link mounts..."thumbsup" |
Re: Sloski's simple berg build Mike, I have some Wraith scale chubs you can use for mock up. But you can't file them. I'll check tomorrow for some other chubs I might have. |
Re: Sloski's simple berg build Thanx Doug, But the spline on the tubes are GONE.....:shock::lmao::lmao: and im just going to go the scx10 route......:) it was the easy option for me......"thumbsup" |
All times are GMT -6. The time now is 01:22 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com