What are you guys powering your Sawbacks with?

[rc-pro1]

Tekin RS - PRO ESC and 21.5t Redline S with stock gearing and Power HD 1501MG servo on 2200mah 3s lipo.

[Barba77]

Toro esc
Toro brushless motor 1650kv, 20,5t
Castle Creations bec
Savox 1210 mg
2x 3s 1400 lipo


Skickat från min iPad med Tapatalk

[QDRHRSE]

Originally Posted by rc-pro1

Tekin RS - PRO ESC and 21.5t Redline S with stock gearing and Power HD 1501MG servo on 2200mah 3s lipo.

You think a 17.5 or 13.5 would run on 3s?

[ZippoMan]

17.5 should easily!! Just be careful with the throttle finger.

[JatoTheRipper]

HobbyKing X-Car 45A ESC - $11
RC4WD 35T motor - $10
Solar D772 servo - $20
Stock gearing

I might change the ESC to the HobbyWing WP-1060 which is a 60A, waterproof ESC. But it's twice the price of the HobbyKing ESC at a "whopping" $20.

[OSRC]

Originally Posted by JatoTheRipper

HobbyKing X-Car 45A ESC - $11
RC4WD 35T motor - $10
Solar D772 servo - $20
Stock gearing

Same, but a 645MG for steering duties. 2200mah 2S

[Brad_striker]

I run the following

Intergy 55t motor
Castle sidewinder v3 esc
Castle 10amp Bec
Savox 1258tg steering
2200 mah 3s spyder packs

Haven't run it yet trying to work out how to mount mojave body !

[idaho]

Ae2, old peak performance Animal quad16t, 15t pinion, 2s

[Dialed]

Tekin FXR rc4wd 45 turn on 3s.

[notarex]

Integy 55T lathe, Novak Rooster, 15T pinion, Hitec 645MG, 3000NIMH

[k7zpj]

HH Waterproof BRXL Esc.
HH TorqueMaster Expert 35T with 11T Gmade pinion
Hitec HS7954SH servo / CC BEC @ 7.4v
HH 3S 1300mah lipo

[SuperDutyScaler]

Traxxas 2075 steering
Traxxas 5000ma stick pack
Novak sensored-based brushless 21.5T (19tooth)
Now running a Novak Rooster crawler with HH 35T torque master (19tooth)

[genetix_drftr]

HPI speed control from my sprint 2
TF40 tx/rx
Integy 35t


Sent from my iPad using Tapatalk

[WesleyRoy]

I run a 27t Holmes Torquemaster pro, on 14t pinion on 2s. However it feels like its still undergeard, because its revvin zo high when i just go at just walk speed.
Motor doesnt feel warm. What do you guys advice, do i have te right motor for the job, or should ik go with a lower turn motor on 3s?

[konasubs]

tekin fxr with tekin HD35t motor with a pinion 2 teeth larger than stock....gobs of torque.....smoked all the scx10s in the tractor pull but still loads of low end torque without getting hot....

[Natedog]

Originally Posted by WesleyRoy

I run a 27t Holmes Torquemaster pro, on 14t pinion on 2s. However it feels like its still undergeard, because its revvin zo high when i just go at just walk speed.
Motor doesnt feel warm. What do you guys advice, do i have te right motor for the job, or should ik go with a lower turn motor on 3s?

Some good combos here.

That sounds pretty good, if motor is barely warm then go 1 - 2 teeth larger on the pinion and test it again keeping close eye on motor temps.

[WesleyRoy]

Dont think this is the right combo for this car, last ride my Sawback just stopped, if i push it then it goes again. Looks like theres something with the motor, changed it for a cheaper 27t expert motor i had laying around, just to make sure i dont ruin my expencsive pro handwound motor.

[Natedog]

Originally Posted by WesleyRoy

Dont think this is the right combo for this car, last ride my Sawback just stopped, if i push it then it goes again. Looks like theres something with the motor, changed it for a cheaper 27t expert motor i had laying around, just to make sure i dont ruin my expencsive pro handwound motor.

Sounds like brushes are worn out, time to turn the comm and install new brushes.