12-21-2015, 08:35 PM | #1 |
Quarry Creeper Join Date: May 2013 Location: no-water-no-trees-country
Posts: 450
| Sawback Vaterra Bronco
Not sure, if I manage to keep this thread updated, but I wanted to let you all know, how a Vaterra Bronco body fits on the Sawback chassis. I have been always busy with my other rigs and almost forgot I had a sawback. I actually liked it, but somehow never drove it much. I recently installed a Vaterra Blazer on one of my SCX10 chassis and loved the oversized look of it. So I wanted that Bronco body also! First: The body is huge! Even 1.9 wheels look tiny underneath it. You could probably build one of those russian dolls out of a small Tamiya Bronco, put HPI's Bronco over it and then the Vaterra on top covering them all - lol. Sawback chassis wheelbase is 287mm, Vaterra Bronco is 278ish. So about 10mm shorter. First I wanted to change the leaf spring mounts but went the easier route. I just cut the chassis in half and took about 12mm out on each side. That's not only the difference needed for the wheelbase but also the distance between the outer screw holes on the skid plate - so that is a perfect fit Excuse the "crappy" paint job - this used to be a military version I used some L-shaped aluminum that I had laying around to join the front and back together. Would serve as a start to hold an interior as well - but more about that further down. So this is what it looks like for now: Notice the Maxxis Trepadors which have a large diameter already. They fit easily into the wheel arches and tuck in too. I am waiting on hex adapters with a larger offset for the steelies in order to get a wider track. Haven't taken pictures of the next steps yet, but I hinged the body at the rear end and used earth magnets mounted to the top of the former body mounts, that will hold down the front of the body. Interior: I chopped up the old Sawback Willy's wannabe body - was never fond of it at all - and used it as an interior. Fits perfectly under the Bronco body - by the way: kudos for this trick have to go to a guy on facebook (Ken A.)! Great idea! Waiting for better weather so I can paint the body This is the look I am going for: More to follow during the holidays. Can't wait to take the good old Saawback out on a run! |
Sponsored Links | |
12-21-2015, 08:54 PM | #2 |
Newbie Join Date: Aug 2014 Location: Abington
Posts: 10
| Re: Sawback Vaterra Bronco
Just awesome. Sent from my Z970 using Tapatalk |
12-24-2015, 01:22 AM | #3 |
I wanna be Dave Join Date: Jan 2006 Location: Corruptifornia
Posts: 12,107
| Re: Sawback Vaterra Bronco
Off to a great start!
|
01-06-2016, 08:55 AM | #4 |
Quarry Creeper Join Date: May 2013 Location: no-water-no-trees-country
Posts: 450
| Re: Sawback Vaterra Bronco
Weather is nasty - raining and freezing here :-( Hardly any progress... Here is just a shot of the Sawback under the Bronco body -which I hinged in the back for easier access: Hoping for better temps so I can paint that sucker! Oh, by the way: I ran a Y-harness from the steering servo to another one behind the dash board. Steering wheel is turning too :-) |
01-06-2016, 07:09 PM | #5 |
Rock Crawler Join Date: Dec 2014 Location: In the sticks
Posts: 913
| Re: Sawback Vaterra Bronco
I'm really liking this body on the Sawback!
|
01-06-2016, 09:06 PM | #6 |
Quarry Creeper Join Date: Jul 2014 Location: saranac
Posts: 310
| Re: Sawback Vaterra Bronco
Nice touch with the steering wheel.
|
01-11-2016, 11:04 AM | #7 |
I wanna be Dave Join Date: Jan 2006 Location: Corruptifornia
Posts: 12,107
| Re: Sawback Vaterra Bronco |
01-11-2016, 12:22 PM | #8 |
Quarry Creeper Join Date: May 2013 Location: no-water-no-trees-country
Posts: 450
| Re: Sawback Vaterra Bronco
Thanks guys - hope, this week will be sunnier and warmer. Can't wait to paint the body!
|
01-19-2016, 10:22 AM | #9 |
Rock Crawler Join Date: Feb 2007 Location: Simi Vly
Posts: 818
| Re: Sawback Vaterra Bronco
Huge Bronco fan here. Be definitely watching this!
|
01-19-2016, 06:34 PM | #10 |
Quarry Creeper Join Date: Dec 2015 Location: NY
Posts: 211
| Re: Sawback Vaterra Bronco
keeping an eye on this! cant wait to see how this comes out
|
01-19-2016, 06:39 PM | #11 |
Quarry Creeper Join Date: May 2013 Location: no-water-no-trees-country
Posts: 450
| Re: Sawback Vaterra Bronco
Lol - I just ordered an RC4WD Blazer and almost thought it is even cooler than this Bronco, so I had the idea of donating this Sawback chassis again - but then, the weather is getting better and it fits so well, so I will go ahead and paint it this week for sure - yes! Still figuring out how to fit proper wheel wells in the front. I have several plastic containers I intended to use, but none of them are "deep" enough, which means, they don't fill the room between chassis and body... any suggestions? These have to be much deeper than the usual containers.
|
01-20-2016, 07:59 AM | #12 |
Rock Crawler Join Date: Feb 2007 Location: Simi Vly
Posts: 818
| Re: Sawback Vaterra Bronco
Do both rigs!!!!
|
01-20-2016, 08:05 AM | #13 |
Quarry Creeper Join Date: May 2013 Location: no-water-no-trees-country
Posts: 450
| Re: Sawback Vaterra Bronco |
01-21-2016, 02:40 PM | #14 |
Quarry Creeper Join Date: Feb 2015 Location: Amongst the UTards
Posts: 211
| Re: Sawback Vaterra Bronco
Needs coil springs up front to be a scale Bronco. Other than that great project!
|
01-21-2016, 04:03 PM | #15 | |
Quarry Creeper Join Date: May 2013 Location: no-water-no-trees-country
Posts: 450
| Re: Sawback Vaterra Bronco Quote:
3 or 4 linked? Linked at all? Maybe I do throw the Blazer on this chassis and build a different one for the Bronco | |
01-21-2016, 06:27 PM | #16 |
Rock Crawler Join Date: Dec 2014 Location: In the sticks
Posts: 913
| Re: Sawback Vaterra Bronco
Bronco front suspension. Track bar is hidden by the draglink. Just in case you really do want to go this rout. |
02-01-2016, 02:56 PM | #17 |
Quarry Creeper Join Date: May 2013 Location: no-water-no-trees-country
Posts: 450
| Re: Sawback Vaterra Bronco
Update: Finished - well almost. Only a few details left to be done. Photobucket seems to be down, so here is just a teaser shot. Will upload more tonight |
02-01-2016, 06:35 PM | #18 |
Quarry Creeper Join Date: May 2013 Location: no-water-no-trees-country
Posts: 450
| Re: Sawback Vaterra Bronco
So, the new ride is added to the fleet: Still need to do something about the white letter sticker and the bumper is too plain. Made some wheel wells, winch is missing the hook. Got some delrin leaf springs from "Peppe" (rc-crawler.it) which still need to be broken in - but hopefully won't break. I painted Tamiya copper, then black on the inside. Afterwards I shot the roof with the same black as a primer. Then finished it off with a thin layer of flat black Krylon. Still have to finish the underside. The dashboard is made by rc-crawler.it as well - I just made it wider and added a top part to it. The steering wheel and the driver's arm actually turns - attached to a second servo with a y-harness behind the dash. And we got a driver too: the "six million dollar man" Lee Majors |
02-01-2016, 07:38 PM | #19 |
Rock Crawler Join Date: Dec 2014 Location: In the sticks
Posts: 913
| Re: Sawback Vaterra Bronco
I think I just fell in love. Great job!
|
02-01-2016, 07:55 PM | #20 |
Quarry Creeper Join Date: Feb 2009 Location: Rocky Mountains
Posts: 241
| Re: Sawback Vaterra Bronco
That is AMAZING! Love it!
|
Sawback Vaterra Bronco - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Sawback v4.0 Bronco | stevem50 | 1.9 Scale Rigs | 8 | 12-06-2015 08:50 PM |
GCM Side Sliders for Vaterra Bronco | Generis | Vaterra Ascender | 5 | 11-27-2015 12:21 PM |
Well, Here is the new Vaterra Bronco | [HOONIGAN] | Vaterra Ascender | 69 | 10-22-2015 02:22 PM |
New Vaterra Bronco Ascender | Killa-Cotton | General Crawlers | 5 | 08-12-2015 03:27 PM |
Thread Tools | |
Display Modes | |
| |