|
| LinkBack | Thread Tools | Display Modes |
01-18-2006, 01:11 AM | #1 |
Rock Crawler Join Date: Feb 2005 Location: Hardin, KY
Posts: 976
| Wont shift into high anymore... help?
i just put high range back in my crawler because i found i did not have enough wheelspeed for climbing hills. got it all back together and the back axle is acting like its in nuetral. i just had it completely apart, so i know there is no broken pins or anything..... |
Sponsored Links | |
01-18-2006, 01:32 AM | #2 |
I wanna be Dave Join Date: Sep 2005 Location: USA
Posts: 11,196
|
There really is only two reasons way. ( I think.) 1. The 4 small ballbearings under the center sleeve. If they fell out it would think it's in nuetral. Or they could be stripped. 2. the arm isn't moving over far enough over to put it in HI. Check these two things over real good and makes sure all of it working right. the white gears for the Hi/Low motor might not be inlined right. These are the only reasons I can think of. |
01-18-2006, 11:32 AM | #3 |
Newbie Join Date: Sep 2005 Location: Sintrul Poynt
Posts: 28
| That happend to me once when I put the high/low arm back on didn't center it over the ring on the coupler, arm would move but wouldn't take the coupler with it. |
01-18-2006, 11:42 AM | #4 |
Rock Crawler Join Date: Feb 2005 Location: Hardin, KY
Posts: 976
|
i think i found the problem :neutral: unfortuneately, one of the "bearings" in the high/low case fell out. anyone have one they can part with? i have been through all my old bicycle bearings and nothing will fit EDIT: ok, WTF. it works fine without the axle cover in plce, shifts like normal and everything. last night i could hold the axle with my 2 fingers and pull the throttle and the motor would spin, but the axle wouldn't..... i still think its the little bearing doing it. i need a bearing and the metal rod that the gear (gear that moves the black arm) spins on (dunno where it went, all my nylint parts were in a box) who wants to hook me up? Last edited by SlammedMini469; 01-18-2006 at 11:47 AM. |
01-18-2006, 12:22 PM | #5 |
Rock Crawler Join Date: Feb 2005 Location: Hardin, KY
Posts: 976
|
ok, heres the problem. after sitting here shifting it back and forth with the cover off i finally got it to do it. the black arm will pop up over the white gear and it will go to the center (where the balls aren't engaging the high or low gearset), therefore it is like nuetral. could only get it to do it once. anyone else had this problem? question about parts still stands though. anyone got the rod and/or bearing they can part with? |
01-18-2006, 12:29 PM | #6 |
Newbie Join Date: Sep 2005 Location: Sintrul Poynt
Posts: 28
|
Not to sound stupid but if the bearings are in is the black arm seated all the way and the screw tight? Another problem I've had was testing it with just the housing clips holding it together without the screws and the housing flexed enough for the arm gear to slip.
|
01-18-2006, 12:33 PM | #7 |
Rock Crawler Join Date: Feb 2005 Location: Hardin, KY
Posts: 976
|
yes, its seated as far as it can go, screws are all tight, bearings in the slider are good, its the bearings in the high/low set that i am missing one of. i had it all back together last night and it still had the problem. Last edited by SlammedMini469; 01-18-2006 at 12:36 PM. |
01-18-2006, 02:10 PM | #8 |
Rock Crawler Join Date: Feb 2005 Location: Hardin, KY
Posts: 976
|
well, it shifts fine now....without the cover....if i put the cover on it will go to low, but not back to high... i wanna play with this thing today, but cant if it wont shift right :neutral: |
01-18-2006, 04:38 PM | #9 |
Rock Crawler Join Date: Feb 2005 Location: Hardin, KY
Posts: 976
|
anyone?
|
01-18-2006, 04:47 PM | #10 |
Newbie Join Date: Oct 2005 Location: Brecksville
Posts: 23
|
ok.......i really dont want to go back and read again sorry which axle is not working correctly? the back one right? Last edited by C85D4x4; 01-18-2006 at 04:50 PM. |
01-18-2006, 04:52 PM | #11 |
Rock Crawler Join Date: Feb 2005 Location: Hardin, KY
Posts: 976
|
back front works fine |
01-18-2006, 05:01 PM | #12 |
Newbie Join Date: Oct 2005 Location: Brecksville
Posts: 23
|
does the black arm still have the spring inside? and make sure the arm isnt too tight also right now i cant help too much b/c i dont have my crawler with me to look at , so i cant play around with it to see what i can fig out:? Last edited by C85D4x4; 01-18-2006 at 05:06 PM. |
01-18-2006, 05:03 PM | #13 |
Rock Crawler Join Date: Feb 2005 Location: Hardin, KY
Posts: 976
|
spring is fine, arm pivots freely........ well, im about to just give up and lock it back in low. sh!t is getting annoying. |
01-18-2006, 05:07 PM | #14 |
Newbie Join Date: Oct 2005 Location: Brecksville
Posts: 23
|
Also......... when you said you had taken the high range out what did you do to it to make this work? |
01-18-2006, 05:20 PM | #15 |
Rock Crawler Join Date: Feb 2005 Location: Hardin, KY
Posts: 976
|
take out the switches in the front axle, shifter motor and gears, clip the wires, pull the wires out, hook the black and white wires together that went to the "low" button, then take the motor and gears out of the back.....hot glued the sliders in place and it was locked in low.....easy as pie.... everything works perfectly with the cover off the back axle, but if i put it on it wont shift into high, it just goes from low to "nuetral" |
01-18-2006, 05:25 PM | #16 |
Newbie Join Date: Oct 2005 Location: Brecksville
Posts: 23
|
hmmmm maybe some how something is rubing on the cover when you put it back on:neutral: this maybe a dumb question but......are you sure that the white shifting gear isnt upside down and all the gears are meshing correctly Last edited by C85D4x4; 01-18-2006 at 05:29 PM. |
Thread Tools | |
Display Modes | |
| |