RCCrawler Forums

hairba11 · 03-21-2007, 07:37 PM

Truck Base :Mini-LST

ESC: stock losi dual motor esc

Motor(s): two 141:1 gear reduction units
http://www.allelectronics.com/cgi-bi...OR,_USED_.html

Servo(s):futaba full size front and rear

Trans: front, direct from gearmotor to diff with driveshaft
rear, direct chain drive from gearmotor to diff input cup slotted for later this week right now it is front wheel drive

Axles:Stock rear lubricated with JB-Weld, 3 racing cranked down ball diff up front

Tires:Moab's with 3/8 inch foam and 2.2 wheels on 1:10 alloy adapters

WB:9.25in from axle to axle

Overall Width:10 in

Diff clearance:2 in

Center Chassis clearance:not much 2.5 in

Overall length:14 in

Rokzilla · 03-25-2007, 06:56 AM

Truck Base : Extended ESP Rokzilla Chassis

ESC: Rebel 2

Motor(s): Integy 55t

Servo(s): Hitec 645mg

Trans: Clodbuster

Axles: Clodbuster, Trax gear Posi

Tires: Imex Jumbo Pullers

WB: 18"

Overall Width: 16"

Diff clearance: 2"

Center Chassis clearance: 3 3/4"

Overall height: 11 1/4"

ColquittCustom405 · 03-25-2007, 08:24 AM

Truck Base :Tamiya Bruiser

ESC:Novak Super Duty

Motor(s):550 can

Servo(s):Hitec/JR

Trans:Modified EMaxx

Axles:TLT

Tires:RC4WD BL's Moabs

ksully · 03-26-2007, 02:17 PM

Newbright rockcrawler
imex red rock tires 2.2
stock suspension cups removed at top of shocks
custom painted by myself

Mike Poulson · 03-28-2007, 07:44 AM

Truck Base : Associated TC3\B4

ESC: Mamba 25

Motor(s): Axi 2212\26

Servo(s): JR

Trans: Spooled B4

Axles: Spooled TC3\ B4CVD's

Tires: Moab

WB: 12"

Overall Width: 11.5"

Diff clearance: 2"

Center Chassis clearance: 2.5"

Overall height: 6.5"

RydeFab · 03-29-2007, 11:22 AM

pimping 2.2 "r2d2"
pimp slap chassis
tlt axles
r2tranny
super rooster/55t lathe
hitec 5955
spectrum rx/tx
ford f150

super pimping "c3po"
homemade torsion chassis
txt axles
e-maxx tranny/gd600/55t lathe
super rooster
hitec 5955 f/r
spectrum rx/tx
ford excursion

crawler hauler
homemade aluminum chassis
tlt axles
losi xx-t tranny
rebel 2/55t lathe
hitec 645
jr rx/tx
juggy leaf front/4 link rear
ford f650

Generis · 04-11-2007, 12:29 PM

the writeup and pics are here:
www.cardomain.com/ride/628266/13
Enjoy the slow life.

toomessedup · 04-11-2007, 12:39 PM

pti goliath
lrp waterproof runner
integy 55t lathe
hitec 645mg
goliath transmission and axles
imex swamp dogs
13.5 in wheelbase
all electronics fully waterproofed

CRAWLIN 4 FUN · 04-13-2007, 10:38 PM

Truck Base :NN

ESC:NOVACK

Motor(s):65T

Servo(s):HITECH 645MG

Trans:N/A

Axles:CLOD

Tires:IMEX

WB:16"

Overall Width:14"

Diff clearance:2.25

Center Chassis clearance:4.5

Overall height:10.5

G-crawler · 04-30-2007, 02:31 PM

Truck Base : Gmade Spider

ESC: Mamba max

Motor(s): Integy lathes 55t

Servo(s): 5645mg

Trans: None

Axles: Gmade

Tires: Imex red rocks on RC4WD 3,2" beadlocks.

2 movie clips..

http://s172.photobucket.com/albums/w...t=MOV03095.flv

http://s172.photobucket.com/albums/w...t=MOV03093.flv

hairba11 · 05-05-2007, 07:08 PM

Truck Base : Wheely King

ESC: stock

Motor(s): Integy 55t

Servo(s): dual TPro995mg with reverser

Trans: stock, 13/96 gearing

Axles: stock, JB-Weld lockers

Tires: Imex K'rock

WB: 14.5"

Overall Width: 12"

Diff clearance: 2.375"

Center Chassis clearance: 4.75"

Overall height: 10.75"

I'll update when i get the lid done.

Mikekx65 · 05-10-2007, 07:37 PM

Truck Base : nylint

ESC:novak xrs

Motor(s):mini-t stock

Servo(s):water proof traxxas 2055

Trans:none

Axles:nylint

Tires:nylint cut and weighted

cabsover78 · 05-19-2007, 05:11 PM

Truck Base : 2wd nylint

ESC: board

Servo: stock

Motor(s): silver 280 can

Trans: stock

Axles: stock

Tires:front stock, rear stock w/studs

to bad i don't have a body.. o well got a wk 4x4 for scaler on order

krikir · 05-24-2007, 01:47 PM

My very first RC crawler (not my last!).

Kranberry · 05-26-2007, 03:12 PM

my ride
here is my super vs wk
specs:
motor:35t
wb:~14.5
radio:3 ch coming
ws(wheel steer):4ws(not shown)
body:stock soon will change to what i have no clu
wheels:stock 2.2
tires:stock chevrons, soon to be all maxx mashers
chassis: matalic red vs
~pics~

mjh · 06-05-2007, 01:39 PM

Truck Base :CLOD
ESC:TEKIN2
Motor(s):55T LATHES..8t pinions
Servo(s):645'S
Axles:CLOD..locked
Tires:RED ROCKS...ON MAXIMIZER B/L
WB:17 IN.
Overall Width:14 IN.
Diff clearance:2 1/2IN.
Center Chassis clearance:4 3/4 IN.
Overall height:11 IN.
Body:toyota hard body
Shocks:RC4WD internals

krikir · 06-12-2007, 03:18 PM

...and now, after the conversion to the new Bender SW3:

The custom built Delrin® links by Finish-Line-RC (www.finish-line-rc.com) of Denver, CO work perfectly:

Truck Base : Tamiya TLT-1 (Bender SW3 Chassis)

ESC: Castle Creations Mamba MAX

Motor(s): Integy Lathe 55

Servo(s): HiTEC HS-5645MG (x2)

Trans: Stampede Locked

Axles: TLT-1 Locked (bearings)

Tires: Proline® Moab 2.2 on trimmed Stampede Chrome Rims, lead in front, star cut foams

WB: 12.5"

Overall Width:10.25"

Diff clearance:1.5"

Center Chassis clearance:3.5"

Overall height: 8"

Garrett · 06-15-2007, 03:46 PM

Here is mine:

Build thread here ---> Project AVIO-TLT Start...PICS!

Gallery here ---> http://www.putfile.com/garrett85/images/117939

BCV6SVT · 06-28-2007, 11:38 PM

Turf Kreeper

Truck Base : HPI Wheely King
ESC: Traxxas XL-5
Motor: Integy 55T Matrix
Servo: Hi Tec 645
Trans: Stock WK, HPI 96 tooth spur gear, 16 tooth pinion
Axles: Stock WK
Tires: Moab 2.2 on Axial Beadlocks
WB: 13.5"
Overall Width: 11"
Diff clearance: 1.5"
Center Chassis clearance: 2.75"
Overall height: 10"

Crawlerdude75 · 07-04-2007, 09:43 PM

Here is mine--

Truck Base : NN chassis from The Crawler Store

ESC: Tekin Rebel 2

Motor(s): Integy 55 turn lathe motors

Servo(s): Hitec HS645MG's

Trans: Clod

Axles: Clod

Tires: BFT (from the MGT) on stock MGT wheels

WB: 16.25''

Overall Width: 15''

Diff clearance: 2.25''

Center Chassis clearance: 5''

Overall height: About 9.75'' with body

Here is a pic, and if you get RC Driver, in the August 2007 issue on page 129 (above 2nd page of the A123 battery add), you will see this picture
(the crawler is the one in the middle btw

) --

03-25-2007, 08:24 AM	#83
ColquittCustom405 I wanna be Dave Join Date: Dec 2005 Location: Orlando Posts: 7,420	Truck Base :Tamiya Bruiser ESC:Novak Super Duty Motor(s):550 can Servo(s):Hitec/JR Trans:Modified EMaxx Axles:TLT Tires:RC4WD BL's Moabs Attached Images

03-28-2007, 07:44 AM	#85
Mike Poulson Quarry Creeper Join Date: Jan 2006 Location: SLC Posts: 382	Truck Base : Associated TC3\B4 ESC: Mamba 25 Motor(s): Axi 2212\26 Servo(s): JR Trans: Spooled B4 Axles: Spooled TC3\ B4CVD's Tires: Moab WB: 12" Overall Width: 11.5" Diff clearance: 2" Center Chassis clearance: 2.5" Overall height: 6.5" Attached Images

04-11-2007, 12:29 PM	#87
Generis Rock Crawler Join Date: Feb 2007 Location: Crawling Around Posts: 871	my e-savage crawler is done the writeup and pics are here: www.cardomain.com/ride/628266/13 Enjoy the slow life.

04-13-2007, 10:38 PM	#89
CRAWLIN 4 FUN Quarry Creeper Join Date: Mar 2007 Location: Who Knows Posts: 215	Truck Base :NN ESC:NOVACK Motor(s):65T Servo(s):HITECH 645MG Trans:N/A Axles:CLOD Tires:IMEX WB:16" Overall Width:14" Diff clearance:2.25 Center Chassis clearance:4.5 Overall height:10.5 Attached Images

04-30-2007, 02:31 PM	#90
G-crawler RCC Addict Join Date: Feb 2007 Location: sweden Posts: 1,007	My Spider Truck Base : Gmade Spider ESC: Mamba max Motor(s): Integy lathes 55t Servo(s): 5645mg Trans: None Axles: Gmade Tires: Imex red rocks on RC4WD 3,2" beadlocks. 2 movie clips.. http://s172.photobucket.com/albums/w...t=MOV03095.flv http://s172.photobucket.com/albums/w...t=MOV03093.flv Last edited by G-crawler; 04-30-2007 at 03:14 PM.

03-21-2007, 07:37 PM	#81
hairba11 RCC Addict Join Date: Mar 2007 Location: St. Louis (High Ridge) Posts: 1,279	Truck Base :Mini-LST ESC: stock losi dual motor esc Motor(s): two 141:1 gear reduction units http://www.allelectronics.com/cgi-bi...OR,_USED_.html Servo(s):futaba full size front and rear Trans: front, direct from gearmotor to diff with driveshaft rear, direct chain drive from gearmotor to diff input cup slotted for later this week right now it is front wheel drive Axles:Stock rear lubricated with JB-Weld, 3 racing cranked down ball diff up front Tires:Moab's with 3/8 inch foam and 2.2 wheels on 1:10 alloy adapters WB:9.25in from axle to axle Overall Width:10 in Diff clearance:2 in Center Chassis clearance:not much 2.5 in Overall length:14 in

03-25-2007, 06:56 AM	#82
Rokzilla Newbie Join Date: Mar 2006 Location: Salamanca Posts: 14	Truck Base : Extended ESP Rokzilla Chassis ESC: Rebel 2 Motor(s): Integy 55t Servo(s): Hitec 645mg Trans: Clodbuster Axles: Clodbuster, Trax gear Posi Tires: Imex Jumbo Pullers WB: 18" Overall Width: 16" Diff clearance: 2" Center Chassis clearance: 3 3/4" Overall height: 11 1/4"

03-26-2007, 02:17 PM	#84
ksully Rock Stacker Join Date: Mar 2007 Location: on a lake Posts: 80	Newbright rockcrawler imex red rock tires 2.2 stock suspension cups removed at top of shocks custom painted by myself

03-29-2007, 11:22 AM	#86
RydeFab Rock Crawler Join Date: Aug 2006 Location: sleeping in my truck! Posts: 674	pimping 2.2 "r2d2" pimp slap chassis tlt axles r2tranny super rooster/55t lathe hitec 5955 spectrum rx/tx ford f150 super pimping "c3po" homemade torsion chassis txt axles e-maxx tranny/gd600/55t lathe super rooster hitec 5955 f/r spectrum rx/tx ford excursion crawler hauler homemade aluminum chassis tlt axles losi xx-t tranny rebel 2/55t lathe hitec 645 jr rx/tx juggy leaf front/4 link rear ford f650

04-11-2007, 12:39 PM	#88
toomessedup Rock Stacker Join Date: Apr 2007 Location: coeur d alene Posts: 55	pti goliath lrp waterproof runner integy 55t lathe hitec 645mg goliath transmission and axles imex swamp dogs 13.5 in wheelbase all electronics fully waterproofed

05-05-2007, 07:08 PM	#91
hairba11 RCC Addict Join Date: Mar 2007 Location: St. Louis (High Ridge) Posts: 1,279	Truck Base : Wheely King ESC: stock Motor(s): Integy 55t Servo(s): dual TPro995mg with reverser Trans: stock, 13/96 gearing Axles: stock, JB-Weld lockers Tires: Imex K'rock WB: 14.5" Overall Width: 12" Diff clearance: 2.375" Center Chassis clearance: 4.75" Overall height: 10.75" I'll update when i get the lid done.

05-10-2007, 07:37 PM	#92
Mikekx65 Rock Crawler Join Date: Apr 2007 Location: LaSalle Posts: 819	my ride Truck Base : nylint ESC:novak xrs Motor(s):mini-t stock Servo(s):water proof traxxas 2055 Trans:none Axles:nylint Tires:nylint cut and weighted

05-19-2007, 05:11 PM	#93
cabsover78 Pebble Pounder Join Date: Jan 2007 Location: drunken Duncan B.C Posts: 189	Truck Base : 2wd nylint ESC: board Servo: stock Motor(s): silver 280 can Trans: stock Axles: stock Tires:front stock, rear stock w/studs to bad i don't have a body.. o well got a wk 4x4 for scaler on order

05-24-2007, 01:47 PM	#94
krikir Pebble Pounder Join Date: May 2007 Location: "In a van, down by the river!" Posts: 109	Wanna see my new rig? Here it is. My very first RC crawler (not my last!).

05-26-2007, 03:12 PM	#95
Kranberry RCC Addict Join Date: Aug 2006 Location: ****, SL,UT Posts: 1,610	my ride here is my super vs wk specs: motor:35t wb:~14.5 radio:3 ch coming ws(wheel steer):4ws(not shown) body:stock soon will change to what i have no clu wheels:stock 2.2 tires:stock chevrons, soon to be all maxx mashers chassis: matalic red vs ~pics~

Sponsored Links

Members' Rides - No talking - Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
What the #$%#$#@ are ya talking about?	Paul58	Newbie General	10	01-13-2013 04:40 PM
Anybody know what im talking about?!	shadowrejects	Chit Chat	2	05-14-2010 06:26 AM
members 1.1 rides?	SaVaGe MaN SS	Chit Chat	4	03-28-2008 02:48 PM

06-05-2007, 01:39 PM	#96
mjh Quarry Creeper Join Date: Feb 2006 Location: Surrey B.C Canada Posts: 218	Truck Base :CLOD ESC:TEKIN2 Motor(s):55T LATHES..8t pinions Servo(s):645'S Axles:CLOD..locked Tires:RED ROCKS...ON MAXIMIZER B/L WB:17 IN. Overall Width:14 IN. Diff clearance:2 1/2IN. Center Chassis clearance:4 3/4 IN. Overall height:11 IN. Body:toyota hard body Shocks:RC4WD internals Last edited by mjh; 06-05-2007 at 01:51 PM.

06-12-2007, 03:18 PM	#97
krikir Pebble Pounder Join Date: May 2007 Location: "In a van, down by the river!" Posts: 109	TLT-1 Bender SW3 Crawler ...and now, after the conversion to the new Bender SW3: The custom built Delrin® links by Finish-Line-RC (www.finish-line-rc.com) of Denver, CO work perfectly: Truck Base : Tamiya TLT-1 (Bender SW3 Chassis) ESC: Castle Creations Mamba MAX Motor(s): Integy Lathe 55 Servo(s): HiTEC HS-5645MG (x2) Trans: Stampede Locked Axles: TLT-1 Locked (bearings) Tires: Proline® Moab 2.2 on trimmed Stampede Chrome Rims, lead in front, star cut foams WB: 12.5" Overall Width:10.25" Diff clearance:1.5" Center Chassis clearance:3.5" Overall height: 8" Last edited by krikir; 06-14-2007 at 09:23 AM.

06-15-2007, 03:46 PM	#98
Garrett Pebble Pounder Join Date: Apr 2005 Location: World -> Europe -> Italy -> Umbria -> Perugia -> Assisi -> Petrignano di Assisi Posts: 174	Here is mine: Build thread here ---> Project AVIO-TLT Start...PICS! Gallery here ---> http://www.putfile.com/garrett85/images/117939

06-28-2007, 11:38 PM	#99
BCV6SVT Newbie Join Date: May 2007 Location: Van City Posts: 30	Turf Kreeper Truck Base : HPI Wheely King ESC: Traxxas XL-5 Motor: Integy 55T Matrix Servo: Hi Tec 645 Trans: Stock WK, HPI 96 tooth spur gear, 16 tooth pinion Axles: Stock WK Tires: Moab 2.2 on Axial Beadlocks WB: 13.5" Overall Width: 11" Diff clearance: 1.5" Center Chassis clearance: 2.75" Overall height: 10" Last edited by BCV6SVT; 07-11-2007 at 04:12 PM.

07-04-2007, 09:43 PM	#100
Crawlerdude75 I joined the Band! Join Date: Nov 2006 Location: Sierra Vista, Arizona Posts: 55	Here is mine-- Truck Base : NN chassis from The Crawler Store ESC: Tekin Rebel 2 Motor(s): Integy 55 turn lathe motors Servo(s): Hitec HS645MG's Trans: Clod Axles: Clod Tires: BFT (from the MGT) on stock MGT wheels WB: 16.25'' Overall Width: 15'' Diff clearance: 2.25'' Center Chassis clearance: 5'' Overall height: About 9.75'' with body Here is a pic, and if you get RC Driver, in the August 2007 issue on page 129 (above 2nd page of the A123 battery add), you will see this picture (the crawler is the one in the middle btw ) --

RCCrawler Forums

Thread: Members' Rides - No talking