|
| LinkBack | Thread Tools | Display Modes |
07-05-2019, 11:12 AM | #1 |
Pebble Pounder Join Date: Mar 2012 Location: Greece
Posts: 177
| Traxxas maxx driveshafts for scx10 transmission
Which part number of traxxas output yokes I need to match scx10 stock transmission shaft and ar60 axle shaft? I am going to use traxxas 4951X driveshafts. |
Sponsored Links | |
07-05-2019, 11:25 AM | #2 |
I wanna be Dave Join Date: Aug 2004 Location: Tri-cities, WA
Posts: 4,831
| Re: Traxxas maxx driveshafts for scx10 transmission
4927 or 4928 will work. You will have to drill out the yoke for the round shaft and likely remove material to clear the scx trans case but they'll work well.
|
07-05-2019, 02:22 PM | #3 |
Pebble Pounder Join Date: Mar 2012 Location: Greece
Posts: 177
| Re: Traxxas maxx driveshafts for scx10 transmission
Which is the difference between 4927x and 4928x?Also pinion gear axle shaft is 5mm.How thick is scx10 trans shafts because I haven't receive it yet.
|
07-05-2019, 02:33 PM | #4 |
I wanna be Dave Join Date: Aug 2004 Location: Tri-cities, WA
Posts: 4,831
| Re: Traxxas maxx driveshafts for scx10 transmission
It isn't a diameter issue, the hole for the pin on you yoke is too deep so the yoke is against the trans case.
|
07-05-2019, 02:44 PM | #5 |
Pebble Pounder Join Date: Mar 2012 Location: Greece
Posts: 177
| Re: Traxxas maxx driveshafts for scx10 transmission
I got it.So I need to make the hole bigger.Other than that transmission outputs are also 5mm?Why are there two part numbers in yokes?
|
07-05-2019, 02:49 PM | #6 |
I wanna be Dave Join Date: Aug 2004 Location: Tri-cities, WA
Posts: 4,831
| Re: Traxxas maxx driveshafts for scx10 transmission
The hole for the output/pinion is 5mm already but it has 2 flat spots for the traxxas output. Easy to drill the flats out. I have no idea why there are 2 part numbers but I've used them both. |
07-05-2019, 03:01 PM | #7 |
Pebble Pounder Join Date: Mar 2012 Location: Greece
Posts: 177
| Re: Traxxas maxx driveshafts for scx10 transmission
I saw this build with these driveshafts and thought it would be a straight fit.Are there better cheap and light options for driveshaft in that kind of conversion? 8-454's Numero dos! My take on the Sucker Punch |
07-05-2019, 03:04 PM | #8 |
RCC Addict Join Date: Feb 2008 Location: Crawlerado
Posts: 1,411
| Re: Traxxas maxx driveshafts for scx10 transmission 4927 is the 5mm bore yoke for the trans to the diff. 4928 is the 6mm bore for the shafts from the diffs to the wheels. |
07-05-2019, 03:24 PM | #9 |
Pebble Pounder Join Date: Mar 2012 Location: Greece
Posts: 177
| Re: Traxxas maxx driveshafts for scx10 transmission |
07-05-2019, 03:32 PM | #10 |
I wanna be Dave Join Date: Aug 2004 Location: Tri-cities, WA
Posts: 4,831
| Re: Traxxas maxx driveshafts for scx10 transmission
So that's the difference, makes sense why some end up sloppier than others. |
07-05-2019, 03:57 PM | #11 |
Pebble Pounder Join Date: Mar 2012 Location: Greece
Posts: 177
| Re: Traxxas maxx driveshafts for scx10 transmission
I have two questions.I have a pair of slw .350 hubs.It would be better to buy another .350 set for whole car with stock ar60 axles width or keep .350 for the rear and buy a pair of .475 for the front? Also,never had a scx10 transmission and the one I bought comes without spur.How many teeth of spur/pinion it's a good start?The motor possibly will be holmes torquemaster expert 27t. |
Traxxas maxx driveshafts for scx10 transmission - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Ax-10 driveshafts with traxxas summit transmission? | Chevycrawler627 | Newbie General | 2 | 05-24-2012 10:09 PM |
C.I. - 4340 steel - Axial transmission outputs for Traxxas Maxx driveshafts | Nova's Ark | Axial AX-10 Scorpion | 5 | 02-23-2011 08:19 AM |
C.I. - 4340 steel - Axial transmission outputs for Traxxas Maxx driveshafts | Nova's Ark | Axial SCX-10 | 14 | 02-20-2011 08:43 PM |
Thread Tools | |
Display Modes | |
| |