RCCrawler Forums

JohnRobHolmes · 11-13-2010, 08:46 PM

It will be probably four weeks. I am waiting on another round of teardowns to do another 40 motors for matching.

greenjeeper92 · 11-13-2010, 09:33 PM

whats the difference between if i placed an order for just two 45s or had a matched set made?And how long till you have an unmatched set in?

TheSkunkBuster · 12-17-2010, 07:15 PM

anyone know when these will be back in stock i need 2-35t matched for the xr10

JohnRobHolmes · 12-29-2010, 06:35 AM

45t matched sets are ready to rock! 35t matched sets will be done in a few days. They are available for preorder if you need to ensure a fast shipment.

As always, we aren't just taking two motors and timing them to match on a dyno. We are selecting matched pairs from lots of 40 or more motors to ensure that you are REALLY getting a pair that will perform predictable and consistent with each other.

gm0688 · 01-07-2011, 11:29 PM

Will you offer a matched set of these in a combo or recomend 2 speedcontrols for an XR-10?

bogfrog · 01-20-2011, 03:25 AM

Hi JRH Just ordered a set of matched 35T's for my new XR10 are these in stock ready to go?

I think these will be just what the doctor ordered can't wait to see the awsome power of these little beautys! Will be set up similar to Harleys same motors and ESC's so should be good

Cheers Robb.

JohnRobHolmes · 01-20-2011, 07:33 AM

Indeed they are already built, and I will ship it out asap for you.

bogfrog · 01-20-2011, 10:12 AM

Thanks JRH I was pretty sure by reading the last few posts but just wanted to confirm they were ready to go? Thank you very much!

Robb.

bogfrog · 01-31-2011, 10:15 PM

Hi JRH just one question on my matched 35T's I noticed one of the motors is marked "rear" does this mean it is wound in reverse and I should connect to the + & - as per normal or should I disregard this and wire it in reverse as first thought? example: ESC+ to Motor- and ESC- to Motor+

Cheers Robb.

JohnRobHolmes · 02-01-2011, 07:20 AM

The rear marked motor has the endbell flipped, and if you wanted timing I added a bit of forward timing. You can hook up positive to positive on the rear and it should rotate properly.

bogfrog · 02-01-2011, 11:37 AM

Quote:

Originally Posted by JohnRobHolmes

The rear marked motor has the endbell flipped, and if you wanted timing I added a bit of forward timing. You can hook up positive to positive on the rear and it should rotate properly.

Will do & Thanks JRH!

Cheers Robb.

gm0688 · 02-03-2011, 05:58 PM

I ordered a matched set of 45's a while back and I checked my bank and you didnt cash my card yet? Are you waitin cause you predict your brushless will be done soon. Just wonderin whats up?

JohnRobHolmes · 02-03-2011, 09:00 PM

Maybe the transaction failed, do you have the order number? I don't have a lead on the brushless timing.

gm0688 · 02-04-2011, 11:21 AM

Quote:

Originally Posted by JohnRobHolmes

Maybe the transaction failed, do you have the order number? I don't have a lead on the brushless timing.

I will put another order in today. Then I will check on Monday.

bquin · 05-19-2011, 10:01 PM

Set of 40's matched with proper timing........available???

JohnRobHolmes · 05-20-2011, 08:42 AM

We can do speed matched sets no problem. Dyno matched motors require 32 motors in a lot to do properly, and we don't sell enough 40t motors for that.

Just put your rig type in the timing box and we will speed match them and time them for your rig no charge.

I just changed up the site a bit for easier inventory and ordering. Now the Power Matching is available as an option, instead of a motor type. Select it on 35t and 45t motors for precise Power Matched pairs, or on any other motor for basic dyno and speed matching to get your 40t motors as consistently performing as possible!

bquin · 05-20-2011, 09:07 AM

okay John....I will look in to some 35's matched.......get back to you soon...

LUNAticCrawlingCrew · 07-25-2011, 05:47 PM

i want some 35t's for my berg but the website says out of stock any word on when they'll be back in stock?

JohnRobHolmes · 07-25-2011, 05:52 PM

It will be about a week and a half. If you pick them up as a "custom" wind you can get at the front of the list.

LUNAticCrawlingCrew · 08-09-2011, 05:25 PM

Got some ordered courtosy of TeamValadezHobb

Quote:

Originally Posted by JohnRobHolmes

It will be about a week and a half. If you pick them up as a "custom" wind you can get at the front of the list.

01-07-2011, 11:29 PM	#65
gm0688 Rock Crawler Join Date: Jul 2009 Location: greeley Posts: 545	Will you offer a matched set of these in a combo or recomend 2 speedcontrols for an XR-10? Last edited by JohnRobHolmes; 05-20-2011 at 08:51 AM.

05-20-2011, 08:42 AM	#76
JohnRobHolmes owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down! Posts: 20,290	We can do speed matched sets no problem. Dyno matched motors require 32 motors in a lot to do properly, and we don't sell enough 40t motors for that. Just put your rig type in the timing box and we will speed match them and time them for your rig no charge. I just changed up the site a bit for easier inventory and ordering. Now the Power Matching is available as an option, instead of a motor type. Select it on 35t and 45t motors for precise Power Matched pairs, or on any other motor for basic dyno and speed matching to get your 40t motors as consistently performing as possible! Last edited by JohnRobHolmes; 05-20-2011 at 09:04 AM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

11-13-2010, 08:46 PM	#61
JohnRobHolmes owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down! Posts: 20,290	It will be probably four weeks. I am waiting on another round of teardowns to do another 40 motors for matching.

11-13-2010, 09:33 PM	#62
greenjeeper92 Quarry Creeper Join Date: Nov 2009 Location: East Greenville Posts: 226	whats the difference between if i placed an order for just two 45s or had a matched set made?And how long till you have an unmatched set in?

12-17-2010, 07:15 PM	#63
TheSkunkBuster Pebble Pounder Join Date: Feb 2010 Location: Arvada Posts: 96	anyone know when these will be back in stock i need 2-35t matched for the xr10

12-29-2010, 06:35 AM	#64
JohnRobHolmes owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down! Posts: 20,290	45t matched sets are ready to rock! 35t matched sets will be done in a few days. They are available for preorder if you need to ensure a fast shipment. As always, we aren't just taking two motors and timing them to match on a dyno. We are selecting matched pairs from lots of 40 or more motors to ensure that you are REALLY getting a pair that will perform predictable and consistent with each other.

01-20-2011, 03:25 AM	#66
bogfrog Pebble Pounder Join Date: Aug 2010 Location: Melbourne, Victoria, Australia. Posts: 152	Hi JRH Just ordered a set of matched 35T's for my new XR10 are these in stock ready to go? I think these will be just what the doctor ordered can't wait to see the awsome power of these little beautys! Will be set up similar to Harleys same motors and ESC's so should be good Cheers Robb.

01-20-2011, 07:33 AM	#67
JohnRobHolmes owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down! Posts: 20,290	Indeed they are already built, and I will ship it out asap for you.

01-20-2011, 10:12 AM	#68
bogfrog Pebble Pounder Join Date: Aug 2010 Location: Melbourne, Victoria, Australia. Posts: 152	Thanks JRH I was pretty sure by reading the last few posts but just wanted to confirm they were ready to go? Thank you very much! Robb.

01-31-2011, 10:15 PM	#69
bogfrog Pebble Pounder Join Date: Aug 2010 Location: Melbourne, Victoria, Australia. Posts: 152	Hi JRH just one question on my matched 35T's I noticed one of the motors is marked "rear" does this mean it is wound in reverse and I should connect to the + & - as per normal or should I disregard this and wire it in reverse as first thought? example: ESC+ to Motor- and ESC- to Motor+ Cheers Robb.

02-01-2011, 07:20 AM	#70
JohnRobHolmes owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down! Posts: 20,290	The rear marked motor has the endbell flipped, and if you wanted timing I added a bit of forward timing. You can hook up positive to positive on the rear and it should rotate properly.

02-03-2011, 05:58 PM	#72
gm0688 Rock Crawler Join Date: Jul 2009 Location: greeley Posts: 545	I ordered a matched set of 45's a while back and I checked my bank and you didnt cash my card yet? Are you waitin cause you predict your brushless will be done soon. Just wonderin whats up?

Sponsored Links

02-03-2011, 09:00 PM	#73
JohnRobHolmes owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down! Posts: 20,290	Maybe the transaction failed, do you have the order number? I don't have a lead on the brushless timing.

05-19-2011, 10:01 PM	#75
bquin Quarry Creeper Join Date: Feb 2009 Location: Glendale Az Posts: 384	Set of 40's matched with proper timing........available???

05-20-2011, 09:07 AM	#77
bquin Quarry Creeper Join Date: Feb 2009 Location: Glendale Az Posts: 384	okay John....I will look in to some 35's matched.......get back to you soon...

07-25-2011, 05:47 PM	#78
LUNAticCrawlingCrew Pebble Pounder Join Date: Apr 2011 Location: El Paso Posts: 191	i want some 35t's for my berg but the website says out of stock any word on when they'll be back in stock?

07-25-2011, 05:52 PM	#79
JohnRobHolmes owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down! Posts: 20,290	It will be about a week and a half. If you pick them up as a "custom" wind you can get at the front of the list.

RCCrawler Forums

Thread: Need some motors for your MOA? TorqueMaster Pro 540- Matched Sets