01-12-2012, 07:38 PM | #21 |
Quarry Creeper Join Date: Oct 2007 Location: Sheboygan
Posts: 326
| Re: The scorpion killer
That's great you got it to work out. Nothing like waiting until the last minute just like me You will have to watch which aluminum knuckles you buy down the road as the ones I have don't have enough material in them to allow them to be bored out for the 15mm bearing.
|
Sponsored Links | |
01-13-2012, 05:03 AM | #22 |
RCC Addict Join Date: Nov 2009 Location: Tulsa
Posts: 1,667
|
Yeah that's what I was looking at. I have rcp Knuckles and integy knuckles. Maybe I'll have to switch to bushings if I can find one that will fit.
|
01-14-2012, 02:39 PM | #23 |
RCC Addict Join Date: Nov 2009 Location: Tulsa
Posts: 1,667
|
Got the steering close to done. I got in a hurry and cut one of the cvd's too short so I'll have to get another one to complete this. |
01-15-2012, 03:28 PM | #24 |
RCC Addict Join Date: Nov 2009 Location: Tulsa
Posts: 1,667
|
Got this all set up should be ready to go just need another set of cvd's and it'll be golden. I think these axles need a new name. XRK's or xr kings is what I was thinking haha. Last edited by adamargue; 01-15-2012 at 06:10 PM. |
02-11-2012, 08:10 PM | #25 |
RCC Addict Join Date: Nov 2009 Location: Tulsa
Posts: 1,667
|
Got my other cvd installed. Check out my mod thread. As it sits now. Sent from my HTC PH39100 using Tapatalk |
02-16-2012, 05:48 PM | #26 |
RCC Addict Join Date: Nov 2009 Location: Tulsa
Posts: 1,667
|
Built a new drag link to give me a little more clearance up front. |
02-17-2012, 05:43 AM | #27 |
Quarry Creeper Join Date: Oct 2007 Location: Sheboygan
Posts: 326
| Re: The scorpion killer
You are going to have way to much flex in the linkage like that. The steering is going to suck. I am always willing to give up clearance for performance. Use could use some larger diameter metal rod instead of the allthread, that would help the flex alot. Last edited by stolps; 02-17-2012 at 05:47 AM. |
02-17-2012, 05:55 AM | #28 |
RCC Addict Join Date: Nov 2009 Location: Tulsa
Posts: 1,667
|
I was worried about that I haven't had a chance to test it out yet. I'll have to see if I have a way to beef it up
|
02-17-2012, 06:02 AM | #29 |
Quarry Creeper Join Date: Oct 2007 Location: Sheboygan
Posts: 326
| Re: The scorpion killer
Yeah, I tried something similar to that and it didn't work very good.
|
02-17-2012, 06:12 AM | #30 |
RCC Addict Join Date: Nov 2009 Location: Tulsa
Posts: 1,667
|
I'm going out of town this weekend but I will see what I can do to stiffen it up when I get back. I need to see what I can do to either modify my aluminum knuckles or get some custom high steer ones made so I can get full steering out of these axles.
|
03-20-2017, 09:36 PM | #31 |
Rock Stacker Join Date: Jan 2017 Location: Bakersfield
Posts: 86
| Re: The scorpion killer
I know this is super old but would like to know if any of it ever worked out ? Sent from my iPhone using Tapatalk |
06-02-2017, 06:48 AM | #32 |
RCC Addict Join Date: Nov 2009 Location: Tulsa
Posts: 1,667
| Re: The scorpion killer
I ran it for quite awhile with good luck I had issues with the trans and shelved it. Comping kinda went away in my area. Sent from my iPhone using Tapatalk |
06-02-2017, 08:37 AM | #33 |
Rock Stacker Join Date: Jan 2017 Location: Bakersfield
Posts: 86
| Re: The scorpion killer
Cool thanks for the response Sent from my iPhone using Tapatalk |
| |