| |
04-12-2007, 08:06 PM
| #1 |
| Rock Stacker Join Date: Mar 2007 Location: San Antonio
Posts: 65
|  My WK Crawler Still doing more to it,BUt its getting there ;) ..Running with stock motor and esc in the videos..LMKWYT It made it through this crack in the rocks.Thats good enough for me    My camera only takes 15sec clips.But there cool     These and mre can be seen here http://smg.photobucket.com/albums/v3...Nitro/Crawler/ Hope you guys like and any suggestions on the setup(if noticable) will be appreciated |
|  |
| Sponsored Links | |
| | |
|
04-12-2007, 08:13 PM
| #2 |
| Quarry Creeper  Join Date: Jan 2007 Location: wilkes-barre
Posts: 313
| pretty good so far. looks like it crawls pretty good. I jsut got mine this afternoon in the mail, what all did you do to get where your at? looks like stretched wb with some new links. what did you use for extended shafts? |
|
| |
|
04-12-2007, 08:14 PM
| #3 |
| Quarry Creeper Join Date: Mar 2007 Location: AZ
Posts: 229
| Looks Cool, What servo are you using? |
|
| |
|
04-12-2007, 08:32 PM
| #4 |
| Rock Stacker Join Date: Apr 2007 Location: Canadia
Posts: 86
| Sweet, that thing crawls pretty nice, im also loving that body you got. |
|
| |
|
04-12-2007, 08:33 PM
| #5 |
| Power of the Portals  Join Date: Feb 2004 Location: where ever the wind fawkin blows me, tx
Posts: 4,572
| looks sweet man. Check out the link in my sig. There few guys in s.a. |
|
| |
|
04-12-2007, 08:33 PM
| #6 |
| Rock Stacker Join Date: Mar 2007 Location: San Antonio
Posts: 65
| Thanks fellas!! I used Emaxx shafts 2.5 Revo turnbuckles and pushrods for U&L links 3.3 Revo turnbuckles and Jato turnbuckles for steering locked diffs with poster putty(couldn't bring myself to JB them) Hitec 645 servo w/Racers Edge SS |
|
| |
|
04-12-2007, 08:40 PM
| #7 |
| Rock Stacker Join Date: Apr 2007 Location: Canadia
Posts: 86
| Thanks for the info buddy, may have to go over to my friends house and mod out his daughters Wheelie king..  |
|
| |
|
04-12-2007, 08:44 PM
| #8 | |
| Rock Stacker Join Date: Mar 2007 Location: San Antonio
Posts: 65
| Quote:
I was just given that site address at HobbyTown a couple of weeks back.Just signed up | |
|
| |
|
04-12-2007, 08:53 PM
| #9 | |
| Power of the Portals Join Date: Feb 2004 Location: where ever the wind fawkin blows me, tx
Posts: 4,572
| Quote:
| |
|
| |
|
04-13-2007, 06:39 PM
| #10 | |
| Rock Stacker Join Date: Mar 2007 Location: San Antonio
Posts: 65
| Quote:
eric-YHPM Last edited by 1RCbasher2NV; 04-13-2007 at 06:42 PM. | |
|
| |
|
04-13-2007, 07:45 PM
| #11 |
| Power of the Portals Join Date: Feb 2004 Location: where ever the wind fawkin blows me, tx
Posts: 4,572
| Hey, btw if you don't mind me asking did you buy your wheely king @ hobbytown ? If you did, how much did you pay ? Here the info.... http://www.txrcrca.org/forum/viewtop...er=asc&start=0 Last edited by eric113; 04-13-2007 at 07:49 PM. |
|
| |
|
04-13-2007, 09:33 PM
| #12 |
| Rock Stacker Join Date: Mar 2007 Location: San Antonio
Posts: 65
| I did buy it at HT..It was $189 plus tax for a 2wd |
|
| |
|
04-16-2007, 06:54 PM
| #13 |
| Rock Stacker Join Date: Mar 2007 Location: San Antonio
Posts: 65
| Well on Sat I ordered asome 12-14mm widener adaptors fro the WK and today I got an email that they shipped http://www.rcrockcrawling.com/produc...roducts_id=347 I also ordered some beadlocks.But theyre for another truck http://www.rcrockcrawling.com/produc...roducts_id=155 They're for this truck   Last edited by 1RCbasher2NV; 04-16-2007 at 06:58 PM. |
|
| |
 |
| Thread Tools | |
| Display Modes | |
| |
Linear Mode
