NIRC. Chit Chat

[talmond]

[talmond]

I need some help setting up my new servo in my wraith. I got a 7950 I set all my trims to zero I put blocks to keep the wheels straight and put the servo horn on centered. It has a lot of steering in one direction and hardly any steering in the other. I took the servo horn off and steered the servo it steers a lot in one direction and barely any in the other. Do I need to set up the servo with my radio ? I've never had this issue. I'm running a Dx3R pro if that matters.

[Die-Laughing]

What are your steering end points set to? (EPA L&R) in the transmitter

[thzero]

Originally Posted by talmond

I need some help setting up my new servo in my wraith. I got a 7950 I set all my trims to zero I put blocks to keep the wheels straight and put the servo horn on centered. It has a lot of steering in one direction and hardly any steering in the other. I took the servo horn off and steered the servo it steers a lot in one direction and barely any in the other. Do I need to set up the servo with my radio ? I've never had this issue. I'm running a Dx3R pro if that matters.

You need to first power up the servo without the horn installed and get it to its center position; make sure all the servo trims are set to 0 and EPAs are at 100%. Then put the servo horn on and use the sub trim to dial it out.

[bronc4now]

Originally Posted by talmond

I need some help setting up my new servo in my wraith. I got a 7950 I set all my trims to zero I put blocks to keep the wheels straight and put the servo horn on centered. It has a lot of steering in one direction and hardly any steering in the other. I took the servo horn off and steered the servo it steers a lot in one direction and barely any in the other. Do I need to set up the servo with my radio ? I've never had this issue. I'm running a Dx3R pro if that matters.

With the horn off if you cant get the servo spline to move equal in both directions then servo might be the problem. .id try to play with remote trim to see if servo can even go the direction you what.

[Die-Laughing]

There EPA settings are in there, might have to go on youtube and watch a video on that transmitter to find out how to get there & adjust it. At first, you want to make sure they are at the same value, this will tell the servo to move equal amounts in either direction. Then, when you get it all buttoned up, you can turn the wheel to see if there is any binding or too much steering in certain direction (lower your value in that direction) or if there is not enough steering in either direction (raise your value in that direction).

[bronc4now]

I really want a new body.. dang nikko fj bodys on ebay are going for like $200+
So just thinking ill keep it jeep for a bit since my bumper looks fuuny on anything else. .
Whats the points differents between 2d or 3d interior? Is a dingo or new jeep a 2d example vs like the wrath 3d?

[Die-Laughing]

Yeah, pretty much.

*(any 3D interior must include seat, dash, steering wheel and floor)

You have the 2dr lexan JK, right? Check out that new Jeep body I posted above. That would be killer on your truck.. They are about $130-$150 though. That is a 3D interior.

Or you could go new bright TJ for around $50, new bright 4dr JK for around $80, tamiya TJ for around $50 but, you'll have to make an interior for that one or run 2D.

[talmond]

Originally Posted by bronc4now

With the horn off if you cant get the servo spline to move equal in both directions then servo might be the problem. .id try to play with remote trim to see if servo can even go the direction you what.

With servo horn off it turns good one way but the other way it moves a very small amount ?

[neillarson]

Is this the new one you got from me? Hope not as that had never been powered up.

Is you trim set to 0 and your EPAs set to 100?

[talmond]

Man figured it out total newbie mistake I was only looking at the sub trim steering menu screen and didn't even look at the trim on the main menu screen. I sure feel dumb right about now.

[Die-Laughing]

Eh.. It happens to all of us.

[sally1800]

Rick

what do you think of that 2d? I am dieing to buy one.

[Die-Laughing]

Don't have it yet but, it looks killer. Great for C1 or C2.. I'll be doing a C1. There is a small thread in the general scale section about them. One guy posted some pretty bitchin' pics of his with poisin spyder flares on 1.9 pits. Looks nasty.

[sally1800]

I have been watching, I looks nice.

[badhoopty]

john dropped off the bmf this morning.

im SO getting laid tonight!

[bronc4now]

Originally Posted by Die-Laughing

Nice.. Gotta love the mail lady.

I got myself a little gift as well..


Now, I just need a Gelande II and I'll be set! I heard there might be a couple at the event so, I'm bringing some dough.

So how long did it take to get yours? I just saw he has one yellow with out a top ..does the top come off yours ? And its 10.8" wb so id have to change links maybe just get the jk 4door so I can keep my current wb.. if I go short again id like it to be on a new rig I think..

[Die-Laughing]

I just ordered it last night. Coming from china.. They are telling me around the end of the month. Right about the time I'll be able to get my hands on a GelandeII. They come in red & yellow. Multiple sellers on ebay. There afe a couple new bright TJ's and a cool JK body in the classifieds right now.

[Die-Laughing]

I think they will catch on pretty hard once a couple killer builds happen using them.. Then they will be hard to come by, then they will cost $175-$200.. Then they will drop off a little bit but, still be cool as hell.. Ya know, kinda like the NB JK.

Edit: MIGHT be a good investment to get a handful of them into the country.. Ya know, if you got the money and you're into that sorta thing.

[badhoopty]

i think one of those bodies would top off my bolt-on baller dingo quite nicely...

either that, or a gelandeII body from somebody who doesnt want it.