|
| LinkBack | Thread Tools | Display Modes |
11-14-2017, 12:21 AM | #1 |
Newbie Join Date: Jan 2017 Location: Finland
Posts: 4
| Axle shaft dimensions for MRC
Hi, What is mrc thickness of axle shafts? I need dimension of that part what goes through Bearings at c-hub and knuckles? I have mod hr-racing knuckles and c-hubs to my rc4wd 1/18 gelander but i still need some cvd's to it. Lähetetty minun ONEPLUS A3003 laitteesta Tapatalkilla |
Sponsored Links | |
11-15-2017, 05:25 PM | #2 |
Oppan Gangnam Style Join Date: Jun 2005 Location: Shingle Springs
Posts: 5,164
| Re: Axle shaft dimensions for MRC
All the axle bearings are 4mm I.D. However the inner axle shafts neck down to 3mm but as for where the axle is in the bearings, 4mm. Last edited by chino63; 11-15-2017 at 05:29 PM. |
11-15-2017, 09:10 PM | #3 |
Newbie Join Date: Jan 2017 Location: Finland
Posts: 4
| Re: Axle shaft dimensions for MRC
Ok thanks! Then it would be possible to use. Next problem is where i can get mrc cvd's... Rc4wd's yota 2 axle I.D is a bit over 3mm, so if i try to drill bigger for 4mm axles it would crack. Bearings is to easy change. So where i can get mrc cvd's ? Lähetetty minun ONEPLUS A3003 laitteesta Tapatalkilla |
11-16-2017, 09:45 AM | #4 | |
Oppan Gangnam Style Join Date: Jun 2005 Location: Shingle Springs
Posts: 5,164
| Re: Axle shaft dimensions for MRC Quote:
I have modified Losi Comp Crawler CVD's in all my mini axles. They need to be modified to fit. Turn down to 4mm and cut the two flats to engage the locker as well as turn down part of the stub shafts to fit the inner 4mm bearing at the knuckle. | |
11-16-2017, 02:11 PM | #5 | |
Newbie Join Date: Jan 2017 Location: Finland
Posts: 4
| Re: Axle shaft dimensions for MRC Quote:
And do you know does this work with hotracing MRC1908 and MRC2108? Bearings must be 4x8? Lähetetty minun ONEPLUS A3003 laitteesta Tapatalkilla | |
11-16-2017, 02:37 PM | #6 |
Rock Crawler Join Date: Aug 2007 Location: Philadelphia
Posts: 797
| Re: Axle shaft dimensions for MRC
Just do the XR mod to your MRC axles and run XR Universals. You need XR/Wraith C-Hubs, Knuckles, Universals, and the appropriate bearings. You have to be willing and able to trim the XR universals to fit the MRC axle and locker. It's not hard with a grinder or dremel and a nice flat file. https://www.shapeways.com/product/7T...li=marketplace |
11-16-2017, 09:13 PM | #7 |
Newbie Join Date: Jan 2017 Location: Finland
Posts: 4
| Re: Axle shaft dimensions for MRC
Yes i would if i had mrc axles but i have rc4wd's yota2 axles and those aluminun hubs and knuckles :/
|
Axle shaft dimensions for MRC - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
XR 10 Mod axle shaft.. How much to cut off the shaft? | CrawlCrest | Axial SCX-10 | 4 | 11-15-2015 10:01 PM |
rear shaft dimensions | jebster | Team Losi Comp Crawler | 2 | 10-15-2015 01:36 PM |
best way to join a rwvo drive shaft to the output shaft on the axle | TRAV | Kyosho Crawlers | 12 | 01-29-2012 07:37 PM |
ball bearing dimensions losi mrc | Dutchy | Losi Mini-Rock Crawler | 2 | 11-10-2009 08:14 PM |
Axle dimensions | trulyoffroad | Newbie General | 2 | 04-16-2009 07:52 PM |
Thread Tools | |
Display Modes | |
| |