01-17-2018, 08:47 AM | #1441 |
Quarry Creeper Join Date: Dec 2010 Location: Pontypool, wales
Posts: 364
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
No that’s the front out drives you are drilling out the drive shaft , connection between d/shaft and pinion which is a through hole , if you drill out and mess up the thread you need to replace the d/shaft no need for replacement outdrive , as long as you get a good tight hammer in and plenty of heat it should unscrew Sent from my iPhone using Tapatalk |
Sponsored Links | |
01-17-2018, 08:57 AM | #1442 |
Quarry Creeper Join Date: Jun 2017 Location: St George
Posts: 274
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
Put the tip of your solder iron on the hex end, I guess you could heat up both sides but I just heated up the one side for about 3 min and with a fresh 2mm hex it should come out pretty easy. I learned the hard way on the first one but used the solder tip on the others, make sure you use blue loctite when you put them back in Sent from my iPhone using Tapatalk |
01-17-2018, 09:00 AM | #1443 | |
Quarry Creeper Join Date: Jun 2017 Location: St George
Posts: 274
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck Quote:
How long have you had your truck? I would call horizon and let them know what happened, they are awesome with replacing parts for free. Iv got driveshafts, wheels and tires, a new esc when all I needed was a fan and a few other parts for no charge. Sent from my iPhone using Tapatalk | |
01-17-2018, 07:11 PM | #1444 | |
Newbie Join Date: Dec 2017 Location: Asia
Posts: 45
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck Quote:
| |
01-18-2018, 03:49 AM | #1445 | |
RCC Addict Join Date: Mar 2011 Location: easton
Posts: 1,399
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck Quote:
That is the right part for the center outdrives, but you may also need a new driveshaft. If you went a few pages back, I stripped the driveshaft screw as well but on the transmission side. So to remove I grabbed a Dremel thinking I could just notch the screw and take it out with a flat head screw driver. Unfortunately I couldn’t take the screw out until I had cut the entire outdrive in half. Like yours, mine was brand new just taken out of the box when it happened Sent from my iPhone using Tapatalk | |
01-21-2018, 08:39 AM | #1446 |
I wanna be Dave Join Date: Oct 2012 Location: Medina
Posts: 2,263
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
Got the dual spare set up installed and found some discontinued ProLine Baja Lights on FleaBay |
01-21-2018, 09:12 AM | #1447 |
Quarry Creeper Join Date: Jun 2017 Location: St George
Posts: 274
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
Good find on the lights, iv been looking for some like that, all Iv found was the rpm bucket light set Sent from my iPhone using Tapatalk |
01-21-2018, 09:25 AM | #1448 |
I wanna be Dave Join Date: Oct 2012 Location: Medina
Posts: 2,263
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck |
01-21-2018, 09:31 AM | #1449 |
Quarry Creeper Join Date: Jun 2017 Location: St George
Posts: 274
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
Oh nice, yeah let me know.. thanks! Sent from my iPhone using Tapatalk |
01-21-2018, 10:47 AM | #1450 | |
I wanna be Dave Join Date: Oct 2012 Location: Medina
Posts: 2,263
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck Quote:
https://www.ebay.com/itm/Pro-Line-HI...53.m2749.l2649 | |
01-23-2018, 08:06 AM | #1451 |
Quarry Creeper Join Date: Jun 2017 Location: St George
Posts: 274
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
The link didn’t work but I found them.. thanks Sent from my iPhone using Tapatalk |
01-23-2018, 01:22 PM | #1452 | |
I wanna be Dave Join Date: Oct 2012 Location: Medina
Posts: 2,263
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck Quote:
BTW - you did a Proline Raptor body correct? Did you have to hack it up pretty good to get it to fit properly, or was it a pretty direct cross? Hit me up with the part# if you can, there seems to be a couple versions of the Raptor body. | |
01-23-2018, 01:42 PM | #1453 | |
Newbie Join Date: Jan 2018 Location: Upland
Posts: 5
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck Quote:
I’m interested in doing this as well. Any insight is much appreciated! | |
01-23-2018, 06:24 PM | #1454 |
RCC Addict Join Date: Feb 2016 Location: Santa Maria, CA
Posts: 1,751
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
I've currently got the body removed and a new Proline 3478-00 2017 Raptor body getting ready to go on. From my preliminary mock up (no holes drilled yet) it looks like I'll be able to directly use about half of the body mounts. It might need some short standoffs/longer screws at the very front/hood, and some creative bracketry for the top/rearmost bedside mounts. The wheelbase is a tad short, but if you center up the rear wheel wells, you can just trim a tiny bit off the front of the front wheel wells and no one would notice. I can see that the body will have to come off anytime I'll want to remove the cage, but that has not been nearly as frequent since installing the SSD front bulkhead, so I'll live with it. ...did I mention that I'm painting it fluorescent pink? |
01-24-2018, 04:24 PM | #1455 | |
Quarry Creeper Join Date: Jun 2017 Location: St George
Posts: 274
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck Quote:
It’s the axial yeti tt raptor body. It was pretty easy to fit. I can send you some pics if you want just let me know. I reinforced it with drywall tape and shoe goo but if I were to do it again I would use the rattle can bed liner also. There’s a couple areas that probably needed a second helping of tape. Sent from my iPhone using Tapatalk | |
01-24-2018, 04:27 PM | #1456 | |
Quarry Creeper Join Date: Jun 2017 Location: St George
Posts: 274
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck Quote:
The part number is PRO347800 Sent from my iPhone using Tapatalk | |
01-24-2018, 05:04 PM | #1457 |
I wanna be Dave Join Date: Oct 2012 Location: Medina
Posts: 2,263
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
Does it need the re-endorcement due to the thickness of the lexan?
|
01-24-2018, 05:33 PM | #1458 |
Quarry Creeper Join Date: Jun 2017 Location: St George
Posts: 274
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
Yeah it’s like any short course body and with the weight of the Baja rey it definitely needs some reinforcement Sent from my iPhone using Tapatalk |
01-25-2018, 11:59 PM | #1459 |
Newbie Join Date: Dec 2017 Location: Asia
Posts: 45
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
SSD released a black version of the front bulkhead it seems
|
01-26-2018, 04:02 AM | #1460 |
Newbie Join Date: Dec 2017 Location: Asia
Posts: 45
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
Just had a rear wheel come off is this normal? I looked the wheels hex bolt that it sits on is rounding off on a lot of the corners...
|
Losi Baja Rey 1/10th 4WD RTR desert truck - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Thunder Tiger Jackal 1/10th 4wd Desert Buggy | RichMTB01 | 2.2 Scale Rigs | 17 | 01-19-2016 12:36 AM |
Vaterra 1/10 Twin Hammers DT 1.9 4WD Desert Truck RTR | spectre | Vaterra Twin Hammers | 0 | 10-01-2015 07:54 AM |
HPI Mini Trophy 1/12 Scale 4WD Desert Truck | constantmotion | Non Crawler RC's | 31 | 08-01-2010 09:56 PM |
| |