02-21-2018, 06:44 PM | #1541 | |
RCC Addict Join Date: Mar 2011 Location: easton
Posts: 1,399
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck Quote:
I’m running a hobbywing 3660 3600kv in mine on 3s and it’s absolutely insane. I don’t know if it’s the same one as mine needed to be soldered to the esc Sent from my iPhone using Tapatalk | |
Sponsored Links | |
02-22-2018, 08:42 AM | #1542 |
Quarry Creeper Join Date: Jun 2017 Location: St George
Posts: 274
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
I think yours is sensored mine isn’t. Lhs said the 3660 motors seem to run cooler, not sure I haven’t ran it yet but he’s pretty knowledgeable on everything rc. I 3s proofed mine so can’t wait Sent from my iPhone using Tapatalk |
02-22-2018, 06:25 PM | #1543 |
Quarry Creeper Join Date: Jun 2017 Location: St George
Posts: 274
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
I took it out for a quick run in the backyard and it rips with the new motor. It’s got a lot torque. I have a 12 tooth pinion and might put the 13 back in it but I’ll run a couple of packs through it this weekend and test it out. So far I’m more the impressed with the power, seems to have good top end too but I ran out of room before I could really open it up. Sent from my iPhone using Tapatalk |
02-25-2018, 11:36 AM | #1544 |
Quarry Creeper Join Date: Jun 2017 Location: St George
Posts: 274
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
After running a couple of packs this morning I can say this motor is a big improvement over the stock one. Even though it’s 4000kv it still has a little more topend then the stock one and the low end and torque is much better. About 5 minutes in to the third pack this happened. Other then that I would definitely recommend it for a replacement motor. Sent from my iPhone using Tapatalk |
02-26-2018, 03:03 AM | #1545 |
Newbie Join Date: Dec 2017 Location: Asia
Posts: 45
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
exotec servo horn requires you to file down your servo mounts? I thought it would be a good idea to make it fit out the box if you are making a specialized product. Oh well, I guess it will be no problem for most but I resorted to going back to the losi one. I did just upgrade my servo to sanwa ers-961
Last edited by Reyracer; 02-26-2018 at 03:25 AM. |
02-26-2018, 04:08 PM | #1546 |
RCC Addict Join Date: Aug 2014 Location: Virginia, Near DC, USA
Posts: 1,607
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck |
02-27-2018, 08:45 AM | #1547 |
Quarry Creeper Join Date: Jun 2017 Location: St George
Posts: 274
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
Only the senton gets hucked, this was on a track. Just came out of a turn and saw the back wheel pass me. Maybe I overtightened it Sent from my iPhone using Tapatalk |
02-28-2018, 07:57 PM | #1548 | |
Quarry Creeper Join Date: Feb 2009 Location: Rockaway
Posts: 489
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck Quote:
After just 3 packs I had two cracked stock wheels so i picked up some Team Associated KMC's that should be delivered soon. The only thing that held me back from those (proline) wheels were some saying the bead would not hold. Did you have any issue like that. Just curious for possible future purchase. | |
02-28-2018, 08:02 PM | #1549 |
Quarry Creeper Join Date: Jun 2017 Location: St George
Posts: 274
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
Nope, I never had an issue with the bead not holding through 3 sets of tires. Iv only ran pro line tires too, iv seen where some have had issues running the stock tires with them.My friend has only ran his on 3s and he’s had his longer the me with no issues. It was probably a fluke or I maybe over tightened the wheel. Sent from my iPhone using Tapatalk |
02-28-2018, 08:49 PM | #1550 | |
Quarry Creeper Join Date: Feb 2009 Location: Rockaway
Posts: 489
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck Quote:
thank you | |
02-28-2018, 09:24 PM | #1551 |
Newbie Join Date: Dec 2017 Location: Asia
Posts: 45
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
well my rear wheel hexes are a little rounded i mean inside the rim. Recently I put vaquish nuts with the washer, tightened it up and ran it and the wheel fell off with the wheel nuts still on the axle, is the washer not compatible? because it ate off the plastic. So i guess i must look for a good wheel solution. I need some advice because now my only problem are my wheels...
|
03-03-2018, 06:58 PM | #1552 |
Quarry Creeper Join Date: Jun 2017 Location: St George
Posts: 274
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
Got my new cage and getting ready to put the new body on, can’t wait to get it dirty. Sent from my iPhone using Tapatalk |
03-04-2018, 01:57 AM | #1553 |
Newbie Join Date: Dec 2017 Location: Asia
Posts: 45
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
is double sided tape going to be ok to mount the esc? Last run it seems to have broken both of the plastic mounting points on each side. Not sure of the alternatives maybe super glue. (no idea how the plastic mounts both snapped on each side) Last edited by Reyracer; 03-04-2018 at 02:26 AM. |
03-05-2018, 07:17 PM | #1554 |
RCC Addict Join Date: Feb 2016 Location: Santa Maria, CA
Posts: 1,751
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
I know somebody here mentioned a while back that Proline was working on a trophy truck specific tire, and I just noticed this today: https://www.prolineracing.com/tires/...-medium-tires/ The bfg at wouldn't have been my first choice, but I'm glad to see another tall (4.74") sc tire.
|
03-06-2018, 02:24 AM | #1555 |
Newbie Join Date: Dec 2017 Location: Asia
Posts: 45
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
spend the whole day disassembling the front end and putting the ssd front bulkhead. The diff wont fit in the new casing. One side goes in well the other side refuses and leaves it so it wont fully shut. edit: the side that wont go in is way too tight a fit for the bearing I have tried heating but its not done much. I tested the opposite side and it fits the bearing really well seems like the other side is not identical. Last edited by Reyracer; 03-06-2018 at 03:48 AM. |
03-06-2018, 04:48 AM | #1556 | |
Rock Crawler Join Date: Dec 2009 Location: Suffolk
Posts: 838
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck Quote:
| |
03-06-2018, 11:27 AM | #1557 |
RCC Addict Join Date: Aug 2014 Location: Virginia, Near DC, USA
Posts: 1,607
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
I dunno, I figured I'd just try the Pitbull Rock Beast SC when I got around to trying different tires again.
|
03-10-2018, 03:14 AM | #1558 |
Pebble Pounder Join Date: Sep 2015 Location: Moscow, Russia
Posts: 199
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck |
03-11-2018, 04:29 PM | #1559 |
RCC Addict Join Date: Aug 2014 Location: Virginia, Near DC, USA
Posts: 1,607
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck
Time for a RPM bumper and some respectable wheels.
|
03-14-2018, 07:51 AM | #1560 |
I wanna be Dave Join Date: Oct 2012 Location: Medina
Posts: 2,263
| Re: Losi Baja Rey 1/10th 4WD RTR desert truck Yep - it works well. Get some good 3M stuff. The ears on my ESC both broke off as well early on. It was a stupid crash that was completely my fault. I pulled the ESC and cleaned up, smoothed out the broken off edges and then secured it with 3M double stick tape. I've run it that way for over a year and no issues.
|
Losi Baja Rey 1/10th 4WD RTR desert truck - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Thunder Tiger Jackal 1/10th 4wd Desert Buggy | RichMTB01 | 2.2 Scale Rigs | 17 | 01-19-2016 12:36 AM |
Vaterra 1/10 Twin Hammers DT 1.9 4WD Desert Truck RTR | spectre | Vaterra Twin Hammers | 0 | 10-01-2015 07:54 AM |
HPI Mini Trophy 1/12 Scale 4WD Desert Truck | constantmotion | Non Crawler RC's | 31 | 08-01-2010 09:56 PM |
| |