08-15-2014, 12:25 PM | #21 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
I use 8-32 threaded rod and Traxxas Revo rod ends. I sleeve the rod in cheap plastic water tubing from Lowes. Last edited by robertjpjr; 08-15-2014 at 12:28 PM. |
Sponsored Links | |
08-15-2014, 11:09 PM | #22 |
Pebble Pounder Join Date: May 2013 Location: Nobleboro
Posts: 158
| Re: What are you working on??
Finished up the ford tonight. All tested and ready for Maidens cliff. Should be a challenge with a 14 3/4" whel base and no rear steer. Took a while to dial in the throttle curves on the Traxxas Velineon. Little faster and a lot lighter. Had to mill the side plates down to get the ride height right. Like the Races claws but im thinking she needs chrome spoke internal bead locks to get it where i want it. Tossed in a before pic. Im liking this a lot better! |
08-15-2014, 11:18 PM | #23 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
I like that ford body. My ford is about the same wheelbase.
|
08-15-2014, 11:28 PM | #24 |
Newbie Join Date: Jul 2014 Location: callahan
Posts: 32
| Re: What are you working on??
Been working on an scx10. The basic moving stuff for weight distribution..Nothing picture worthy yet. Sold the deadbolt body and stuck an emaxx body on to g6 with. I have a 56 ford body to paint up then build bumpers/sliders to fit.
|
08-16-2014, 01:31 PM | #25 |
Pebble Pounder Join Date: Jul 2014 Location: Phippsburg, ME
Posts: 143
| Re: What are you working on??
So, I dubbed with my LEDs and found that I didn't like any of the 4 ways I tried mounting them. Finally dug into my old school R/C tool boxes, found the original rear bumper to my Tamiya King Hauler. I cut the tail light sockets from the bumper and zip tied them together, stuck the LEDs in and zip tied them in place. Looks more like it should be a Marshall 1/4 stack amp, rather than driving lights. Until they are lit... |
08-20-2014, 07:43 PM | #26 |
Pebble Pounder Join Date: Nov 2013 Location: Bath,ME
Posts: 159
| Re: What are you working on??
I'm going to start working on a set of steel sliders for the scx10 jeep tomorrow. Their going to be a different design than the ones I made for the ford. I've got a couple ideas in mind but not sure what I'm going build yet.
|
08-20-2014, 08:18 PM | #27 |
Pebble Pounder Join Date: May 2013 Location: Nobleboro
Posts: 158
| Re: What are you working on??
Caught the scratch building bug lol. Those sliders you built for your ford came out killer. Can wait to see what you come up with next. I see a scratch built chassis some day? |
08-21-2014, 05:45 PM | #28 |
Pebble Pounder Join Date: Nov 2013 Location: Bath,ME
Posts: 159
| Re: What are you working on??
So when I got home from work I messed around with a couple ideas for the jeep and I think I'm going to do something like this for it.
|
08-21-2014, 05:53 PM | #29 |
Pebble Pounder Join Date: Jul 2014 Location: Phippsburg, ME
Posts: 143
| Re: What are you working on??
I really like that!!! |
08-29-2014, 11:49 AM | #30 |
Pebble Pounder Join Date: Jul 2014 Location: Phippsburg, ME
Posts: 143
| Re: What are you working on??
So, I found a STAVING deal on a pair of JK bodies for the SCX-10! I can pick them up tomorrow!! Crappy cell phone pics to come.... I hope GoPro hurries the hell up with my replacement camera..... |
08-29-2014, 02:03 PM | #31 |
Pebble Pounder Join Date: Nov 2013 Location: Bath,ME
Posts: 159
| Re: What are you working on??
Nice!! I'm going to order a hilux body to go on the dingo chassis tomorrow. Thinking about trying a steel back half and exo cage on it.
|
08-29-2014, 02:33 PM | #32 |
Pebble Pounder Join Date: Jul 2014 Location: Phippsburg, ME
Posts: 143
| Re: What are you working on??
That will look cool!! Can't wait to see it!! |
08-31-2014, 01:31 PM | #33 |
Pebble Pounder Join Date: Jul 2014 Location: Phippsburg, ME
Posts: 143
| Re: What are you working on??
Got a new to me but used JK body, a new unpainted & uncut JK body, and a set of Maxxis Trepadors. I had to take it for a test drive. I took it to Fort Popham. Even though there's not much there to climb, I still managed to kill a 3300mah NiMH pack! The Jeep body makes it climb so much better!!! I hate my phone's camera, but here's a few pics anyway: |
08-31-2014, 03:01 PM | #34 |
Pebble Pounder Join Date: Nov 2013 Location: Bath,ME
Posts: 159
| Re: What are you working on??
After looking at the slider I made for the jeep for a few weeks I decided I'm not too crazy on that style. So I made this today, I think I like this a little better.
|
08-31-2014, 08:30 PM | #35 |
Rock Stacker Join Date: Apr 2012 Location: Arundel ME.
Posts: 88
| Re: What are you working on??
Yes, I like these better. Nice!
|
09-05-2014, 05:38 PM | #36 |
Pebble Pounder Join Date: Nov 2013 Location: Bath,ME
Posts: 159
| Re: What are you working on??
I'm going to start working on this next week. Building a steel back half and possibly an exo cage.
|
09-06-2014, 06:53 AM | #37 |
Pebble Pounder Join Date: Jul 2014 Location: Phippsburg, ME
Posts: 143
| Re: What are you working on??
That's awesome Kaler! Makes me miss my Tamiya Bruiser.... |
09-06-2014, 03:49 PM | #38 |
Pebble Pounder Join Date: May 2013 Location: Nobleboro
Posts: 158
| Re: What are you working on??
Man cant wait to see how that comes out Kaler. Thought i cooked the sw3 in the ford a few weeks ago. So i dropped 106 on a mmp and 15.5t redline. Just my luck it was the receiver.....again. Thing crawls great and i can still blow mild donuts with it. Plus i can still hill climb. Works out great now i can put the velineon and the sw3 in the boys 2wd slash and pull the glitchy speed passions. Thing will only engage reverse when it wants to.
|
09-07-2014, 04:21 PM | #39 |
Pebble Pounder Join Date: Nov 2013 Location: Bath,ME
Posts: 159
| Re: What are you working on??
I finally found some time to work on the hilux today,but just my luck I ran out of shielding gas in the welder. Figures. This is as far as I got today.
|
09-07-2014, 05:55 PM | #40 |
Pebble Pounder Join Date: May 2013 Location: Nobleboro
Posts: 158
| Re: What are you working on??
What are you using to bend your stock? Thats SICK!!!!!!!
|
What are you working on?? - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Working out | ozyint | Chit Chat | 6 | 08-02-2011 02:34 PM |
Something new I am working on | sparky0068 | 1.9 Scale Rigs | 24 | 08-16-2008 10:14 PM |
Little Something We Was Working On | pureadrenalin | Chit Chat | 33 | 10-22-2007 11:03 AM |
Im Working On A Working Wrecker Any Ideas? | LEDDPIPE | General Scale Talk | 7 | 12-13-2006 11:53 PM |
What I've been working on...... | CSR | Tamiya Txt-1 and Juggernaut | 26 | 11-10-2005 04:54 PM |
| |