12-01-2017, 12:47 PM | #1461 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
Got the bug the last few days to 3D print and redo trucks, etc. So I changed the Dodge SCX10 to the Jeep. Got rid of worn out aluminum brackets and just switched things up a bit. The Jeep body has nice LED's that were flippin expensive, may as well use them. Before: After: |
Sponsored Links | |
12-02-2017, 12:56 PM | #1462 |
I wanna be Dave Join Date: Jun 2016 Location: Deep in the Everglades
Posts: 5,818
| Re: What are you working on??
Just a simple add on, a Viking roller fairlead for OPIE.... what a difference! Hang up and Drive |
12-03-2017, 04:27 PM | #1463 |
Quarry Creeper Join Date: Oct 2011 Location: Westport Island
Posts: 404
| Re: What are you working on??
Safety first! Sent from my iPhone using Tapatalk |
12-07-2017, 10:02 PM | #1464 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
Put some larger (Wider) tires on for the TRX plow truck. The small ones, I think, would be too narrow for effective plowing. With the impending snow this weekend, I'm getting prepared for some fun! The tires are off of my Rustler of all vehicles. 2.2" wheels and Duratrax tires. Last edited by robertjpjr; 12-07-2017 at 10:06 PM. |
12-08-2017, 12:02 AM | #1465 |
RCC Addict Join Date: Nov 2016 Location: 1972 born Christian, Chinese.
Posts: 1,321
| Re: What are you working on??
Working on my SCX10 II Kit now. on Transmission now |
12-09-2017, 02:14 PM | #1466 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
Short video of the TRX4 plowing. The radio started beeping due to low voltage. So turn off your audio after 1 min ! You've been warned https://1drv.ms/v/s!Ap69_oAJ8pjhjiQxxcjpbvoxnavN *Added a photo* Last edited by robertjpjr; 12-09-2017 at 05:23 PM. |
12-09-2017, 05:28 PM | #1467 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
Got the Ascender today! Holy crap this thing is quiet! Ripped out the stock motor and ESC. Put in a HH BRXL and a Axial 55t. Will crawl very slowly now, but still has enough speed on 3s. I'm sure I'll kill the axial motor quicker, but I'll probably run 4s as well. Seeing as I have 2 small 3s, and 1 small 4s to fit the battery tray. On that note, I'm not sold on the "Floating battery tray" idea.. I will try the stock Spectrum radio as well. The trigger is much smoother than the Flysky, I'll give it that. Designing and 3d printing a rear bumper shortly. Last edited by robertjpjr; 12-09-2017 at 05:31 PM. |
12-24-2017, 01:46 PM | #1468 |
Quarry Creeper Join Date: Oct 2011 Location: Westport Island
Posts: 404
| Re: What are you working on??
I finally installed some lights on the TF2, not being a fan of fiddling with connectors while mounting a body I came up with this plan of attack. I isolated the custom springs from the chassis with some old Parma body posts and rings, we’ll see how long it all lasts! Sent from my iPhone using Tapatalk |
12-24-2017, 02:23 PM | #1469 |
RCC Addict Join Date: Oct 2012 Location: Norcal
Posts: 1,261
| Re: What are you working on??
Ive been working on the 1/6 VW lately. I made up some vacuum formed hubcaps to fit in my Gear Head 2.2's. (Final color will be chrome) I also got a start on the interior and dash gauges. It's getting there. By the way, those are 2.2 Swamper XL's. Last edited by Norton; 12-24-2017 at 03:37 PM. |
12-24-2017, 03:03 PM | #1470 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
The SCX10 got some love over the past few days. 3D printed a CMS mount. The SSD axle housings came with the cms mount that attaches to the axle (I believe that's where it came from. I found it in my parts bin.) Made custom length links out of 8-32 rod and windshield washer line. It all works great. Very happy I had what I needed. I was considering purchasing the kit for $60 ish. |
12-24-2017, 03:14 PM | #1471 |
Moderator Join Date: Sep 2008 Location: PA
Posts: 13,935
| Re: What are you working on??
I'll be starting this Christmas gift. |
12-29-2017, 04:25 PM | #1472 |
RCC Addict Join Date: Sep 2015 Location: Southern Maine
Posts: 1,024
| Re: What are you working on??
Pretty sad that this early into the deep dark cold winter season I'm already desperate enough to try once again to get the clodbuster going for some winter snow bashing. Hoping/praying I can actually put a complete battery pack through it before destruction. I have replaced all four axle tubes and knuckles with new pieces in hopes to get rid of petrified 30 year old plastic. Made braces for both top and bottom ears of all four knuckles. Doing away with one steering servo and going to axle mounted servos. Also bought a super cheap dual motor esc on eBay that's good for 4s so that'll insure destruction if 3s wont. I need help I think. Sent from my iPhone using Tapatalk |
12-31-2017, 01:01 PM | #1473 |
Quarry Creeper Join Date: Oct 2011 Location: Westport Island
Posts: 404
| Re: What are you working on??
Tinkering on the assender, had to tuck the bumper about 3/4” so I made new mounting hardware and raised it about a 1/4” also mounted up some BFG’s Before: After: Sent from my iPhone using Tapatalk |
01-07-2018, 03:44 PM | #1474 |
RCC Addict Join Date: Sep 2015 Location: Southern Maine
Posts: 1,024
| Re: What are you working on??
Got the original 1987 body back into decent shape. Leaving it like this for nostalgia I guess. Just detailed the grill and trim. Looks way better I think. Reinforced some cracks and broken bits. Sent from my iPhone using Tapatalk |
01-08-2018, 04:23 PM | #1475 | |
I wanna be Dave Join Date: Jan 2006 Location: Corruptifornia
Posts: 12,107
| Re: What are you working on?? Quote:
Quick search found this https://www.rctech.net/forum/electri...tic-parts.html | |
01-11-2018, 12:08 AM | #1476 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
Made a battery tray for the scx10. Previously I had zip tied the stock metal battery tray to the frame / shock hoops. This way is a bit more secure. I might make a more refined version to put on my site. |
01-14-2018, 09:47 PM | #1477 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
Designed a new bumper. Thoughts? It has 4 different height adjustments, and will fit any width frame from 71-76mm which is Ascender at 71mm, scx10 /10.2 at 73mm, and trx4 at 76mm. 2 spots for 5mm LEDs Winch fairlead I'll upload some better pics later. |
01-20-2018, 07:48 PM | #1478 |
Quarry Creeper Join Date: Oct 2011 Location: Westport Island
Posts: 404
| Re: What are you working on??
Sway bar install on the Assendah. Sent from my iPhone using Tapatalk |
01-20-2018, 08:40 PM | #1479 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
Ordered one of these guys. Plan on modding it to be a bit more functional. Been seeing these truck pop up on Youtube and I believe I saw one here somewhere. https://www.gearbest.com/rc-cars/pp_1131789.html?wid=21 For $35 shipped it seems pretty cool. |
01-20-2018, 09:49 PM | #1480 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
Got another set of cheap 1.9 beadlocks. With the small tires, it seems a bit Mall Crawler ish. I may bake off the stock Ascender tires or buy another set of tires. I'll make due for now. |
What are you working on?? - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Working out | ozyint | Chit Chat | 6 | 08-02-2011 02:34 PM |
Something new I am working on | sparky0068 | 1.9 Scale Rigs | 24 | 08-16-2008 10:14 PM |
Little Something We Was Working On | pureadrenalin | Chit Chat | 33 | 10-22-2007 11:03 AM |
Im Working On A Working Wrecker Any Ideas? | LEDDPIPE | General Scale Talk | 7 | 12-13-2006 11:53 PM |
What I've been working on...... | CSR | Tamiya Txt-1 and Juggernaut | 26 | 11-10-2005 04:54 PM |
| |