07-08-2017, 10:30 PM | #1421 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
Finished the servo winch. Stole one of my 6ch Rx from the scx 10.2. have 2 on order but I'm impatient. Got all the channels working with correct endpoints etc.. Needed a 6ch for the servo winch and a BEC. Works great. Switched out the bumper for durability / clearance / winch line placement. Not my favorite bumper, but it'll do.. Also got the light bar wired in. Next project is bucket LEDs. The body has 12 slots for LEDs. Odd sizing though. Not 5mm and not 3mm. So some finesse and shoe glue I think. If anyone wants the transmitter settings for a flysky gt3b let me know. It's a bit complicated. I may even do a write-up of video later, if there's demand. Last edited by robertjpjr; 07-08-2017 at 10:37 PM. |
Sponsored Links | |
07-12-2017, 06:31 PM | #1422 |
Pebble Pounder Join Date: May 2013 Location: Nobleboro
Posts: 158
| Re: What are you working on??
Been so busy at work I haven't had the drive to do much. Did get the other 5 tires mounted. |
07-13-2017, 05:33 PM | #1423 |
Quarry Creeper Join Date: Oct 2011 Location: Westport Island
Posts: 404
| Re: What are you working on??
Finally got to tinker with the TRX4. Installed a Hitec servo, bec, HH esc. Later I'm gonna mount up some Interco Irok's on SSD's Sent from my iPhone using Tapatalk |
07-13-2017, 06:39 PM | #1424 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
Made some scale items. Need to get some paints I think. |
07-14-2017, 02:56 PM | #1425 |
Quarry Creeper Join Date: Oct 2011 Location: Westport Island
Posts: 404
| Re: What are you working on??
I think it's done.... Sent from my iPhone using Tapatalk |
07-15-2017, 05:26 PM | #1426 |
Pebble Pounder Join Date: May 2013 Location: Nobleboro
Posts: 158
| Re: What are you working on??
Got the rest of my parts ordered for the 6x6 build. rc4wd winch. 50lb dead lift ? that should do it...lol get some more pics up soon. Got most of the pre fitting done. I cant wait to get this thing out for a test run.
|
07-20-2017, 05:20 PM | #1427 |
Pebble Pounder Join Date: May 2013 Location: Nobleboro
Posts: 158
| Re: What are you working on??
Now to get it all together |
07-23-2017, 09:00 AM | #1428 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
Working on eating some friggin awesome breakfast. Red Fox bar and grille breakfast buffet. In the parking lot... J E A L O U S |
07-23-2017, 11:16 AM | #1429 |
Quarry Creeper Join Date: Oct 2011 Location: Westport Island
Posts: 404
| Re: What are you working on??
Where's that's?? Sent from my iPhone using Tapatalk |
07-23-2017, 12:19 PM | #1430 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
Jackson NH I believe. Camping at Glen Ellis campground with some friends. Just did Mt Washington! I'll post pics when I get better service. |
07-23-2017, 08:33 PM | #1431 |
Quarry Creeper Join Date: Jan 2016 Location: US
Posts: 401
| Re: What are you working on??
New paint! Sent from my SM-G900V using Tapatalk |
07-24-2017, 05:20 AM | #1432 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
More NH pics. Went to breakfast saw jeeps. Went to mt Washington, saw jeeps. Good day! For the rally race fans, enjoy some Subaru rubber. Last week they had the Subaru rally race. Travis pastrana set a 5:44 time. Did some crawling at the top of My Washington. First Traxxas Trx-4 ?? |
08-18-2017, 06:50 PM | #1433 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
New body for the SCX10.2 Needs to be stickered up, then beat up! |
08-19-2017, 08:12 AM | #1434 |
Quarry Creeper Join Date: Oct 2011 Location: Westport Island
Posts: 404
| Re: What are you working on??
Adding weight to an already heavy truck: Sent from my iPhone using Tapatalk |
08-19-2017, 12:55 PM | #1435 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
Added magnets to hold body clips to a few trucks. Put decals on the TRX and SCX10.2 Adjusted rear bumper for Toyota body. I will design and 3d print some light buckets for the 4Runner body. Perhaps a roof rack, IDK. |
08-20-2017, 04:23 PM | #1436 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
Printed the 4Runner LED housings. |
08-28-2017, 05:27 PM | #1437 |
Pebble Pounder Join Date: May 2013 Location: Nobleboro
Posts: 158
| Re: What are you working on??
Waiting on parts. again...lol Doing a cantilever set up on the back end of the 6x6. If this works like I hope it does, Big Green is next. I wanna do a dropped bed and this would make it happen. Ahhhhhh the wait...
|
09-01-2017, 04:43 PM | #1438 |
Pebble Pounder Join Date: May 2013 Location: Nobleboro
Posts: 158
| Re: What are you working on??
Has anyone here ever cut a section out of a mip drive shaft and welded it back together? Nick pointed me to the MIP for the yeti for its length. I needed really long ones to fit the FORD, rather sick of the squeaking of the GDS shafts. And the pins falling out. The rear was a dead hit. No modifying needed ,the front however is about an 1/8" too long. so I cut some of the outer splined shaft off. BUT!!!!! unknown to me the inner splined shaft does not have splines all the way to the end. so it goes on and im not catching enough spline to feel comfortable running it as is. Just wondered if anyone has done such a thing. I know there's a few welders here. What say you ?
|
09-01-2017, 07:06 PM | #1439 | |
RCC Addict Join Date: May 2015 Location: Price Twp.
Posts: 1,291
| Re: What are you working on?? Quote:
Sent from my SM-G928V using Tapatalk | |
09-01-2017, 08:41 PM | #1440 |
Pebble Pounder Join Date: Nov 2013 Location: Bath,ME
Posts: 159
| Re: What are you working on??
[QUOTE=Androtaz;5744716]Has anyone here ever cut a section out of a mip drive shaft and welded it back together? Nick pointed me to the MIP for the yeti for its length. I needed really long ones to fit the FORD, rather sick of the squeaking of the GDS shafts. And the pins falling out. The rear was a dead hit. No modifying needed ,the front however is about an 1/8" too long. so I cut some of the outer splined shaft off. BUT!!!!! unknown to me the inner splined shaft does not have splines all the way to the end. so it goes on and im not catching enough spline to feel comfortable running it as is. Just wondered if anyone has done such a thing. I know there's a few welders here. What say you ?[/QUOTE I've never tried it but if you get a spare shaft I think I can do it. |
What are you working on?? - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Working out | ozyint | Chit Chat | 6 | 08-02-2011 02:34 PM |
Something new I am working on | sparky0068 | 1.9 Scale Rigs | 24 | 08-16-2008 10:14 PM |
Little Something We Was Working On | pureadrenalin | Chit Chat | 33 | 10-22-2007 11:03 AM |
Im Working On A Working Wrecker Any Ideas? | LEDDPIPE | General Scale Talk | 7 | 12-13-2006 11:53 PM |
What I've been working on...... | CSR | Tamiya Txt-1 and Juggernaut | 26 | 11-10-2005 04:54 PM |
| |