11-14-2016, 12:11 PM | #221 |
Scale Detail Engineering Join Date: Apr 2010 Location: Turtle Island
Posts: 5,573
| Re: 1/24 Pro-Line "True Scale" Ambush
Just installed the Predator 90 with the stock ESC... soooo much better low end control. The only obstacles were removing and reinstalling the pinion gear and the motor mount screws are a different size. I took the off another Losi. |
Sponsored Links | |
11-14-2016, 04:09 PM | #222 | |||
I wanna be Dave Join Date: Jan 2006 Location: Corruptifornia
Posts: 12,107
| Re: 1/24 Pro-Line "True Scale" Ambush Quote:
Quote:
Quote:
Tekin B1R. | |||
11-14-2016, 06:03 PM | #223 |
Scale Detail Engineering Join Date: Apr 2010 Location: Turtle Island
Posts: 5,573
| Re: 1/24 Pro-Line "True Scale" Ambush
Just ran the Ambush with the new motor and medium set of helper springs front and back. The Predator 90 has a lot more low end control than stock but feels like a little bit less torque and it is a bit slower than stock. I'll take that trade for the control though... I can actually crawl now! I am going to remove the front helper springs as it seemed a bit too stiff although was sidehilling great! |
11-14-2016, 06:45 PM | #224 | |
Rock Crawler Join Date: Mar 2009 Location: Parker, CO
Posts: 742
| Re: 1/24 Pro-Line "True Scale" Ambush Quote:
Picture trying to crawl over a steep rock with the stock motor - you give it throttle as slowly and carefully as you can, but it doesn't move because it needs more volts, until you get to almost half throttle (when voltage is about 4v) but then the truck launches forward too fast because it needs more volts to move when under a load (like a hill or rock). With the 90 turn motor you should be able to get it to move at less than 1/4 throttle (voltage ~2v) - thus, as you said, more control. If you want even more control for crawling, put a 9 tooth pinion and a 56 tooth spur gear on there and you should have even more low speed torque/control. | |
11-29-2016, 06:23 PM | #225 |
Pebble Pounder Join Date: Mar 2016 Location: Houston
Posts: 131
| Re: 1/24 Pro-Line "True Scale" Ambush
Does anybody know where to get drive shafts with a 3mm hole to extend the wheel base of this guy?
|
11-30-2016, 01:50 PM | #226 |
Newbie Join Date: Oct 2011 Location: Under a rock 1st hole on the left
Posts: 21
| Re: 1/24 Pro-Line "True Scale" Ambush
Dear Pro-Line. if you are reading this please make some of your two stage foams in different firmness. That way we the consumer can modify the tires to our liking. Myself, I favor a rigid tire like the ultra4 vehicles run. Thank you.
|
11-30-2016, 02:38 PM | #227 | |
I wanna be Dave Join Date: Jul 2014 Location: Deep South
Posts: 3,444
| Re: 1/24 Pro-Line "True Scale" Ambush Quote:
***Crawler Innovations Micro Foam Set GIVEAWAY*** 3 Winners *** | |
11-30-2016, 03:10 PM | #228 | |||
I wanna be Dave Join Date: Jan 2006 Location: Corruptifornia
Posts: 12,107
| Re: 1/24 Pro-Line "True Scale" Ambush Quote:
Quote:
Quote: | |||
12-02-2016, 04:16 AM | #229 |
Scale Detail Engineering Join Date: Apr 2010 Location: Turtle Island
Posts: 5,573
| Re: 1/24 Pro-Line "True Scale" Ambush
I am loving this little mountain goat! I have big plans for this rig... I think it's time to start my own thread. |
12-02-2016, 05:11 AM | #230 |
I wanna be Dave Join Date: Jul 2014 Location: Deep South
Posts: 3,444
| Re: 1/24 Pro-Line "True Scale" Ambush
Those miclows look good on there. I know a guy not too far away from me with a 1:1 rig like that.
|
12-04-2016, 06:05 PM | #231 |
Pebble Pounder Join Date: Mar 2016 Location: Houston
Posts: 131
| Re: 1/24 Pro-Line "True Scale" Ambush
I got a F150 body to go on my new Ambush. I wasnt very careful with the paint since I was going for a weathered look.There are some details left to add, but once I actually get this thing dirty is should look better. I found some brass tube that sleeves the drive shaft perfectly to extend it rear one. I still need to add the electronics back in, and unfortunately the stock battery will not fit under the hood. I was thinking about fabricating a roll bar to go in the bed, and hopefully at some point get a spare to mount as well. I also need to figure out what to do about that front bumper sticking way out. |
12-06-2016, 01:54 PM | #232 |
Pebble Pounder Join Date: Mar 2016 Location: Houston
Posts: 131
| Re: 1/24 Pro-Line "True Scale" Ambush
The tires are only tacked on the insides, I was able to mount some weights and take it for a short test run today. https://youtu.be/W0XRRX3Tj9o Last edited by Basicbilly; 12-06-2016 at 01:59 PM. Reason: Trying to get the video to embed |
02-09-2017, 04:50 AM | #233 |
Pebble Pounder Join Date: Dec 2006 Location: australia
Posts: 139
| Re: 1/24 Pro-Line "True Scale" Ambush
Is anyone printing any accessories for 1/25 stuff? I'm after a pair of diesel cans, a highlift and a fire extinguisher if anyone knows of any?
|
02-09-2017, 07:58 AM | #234 |
Newbie Join Date: Feb 2016 Location: Richmond
Posts: 9
| Re: 1/24 Pro-Line "True Scale" Ambush |
1/24 Pro-Line "True Scale" Ambush - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
2.2 VP Scale Wheel True 1" and 1.250" Cans | CarterFab | Vendors Tires and wheels | 106 | 05-02-2017 02:43 PM |
True 1" and 1.250" Wheel Cans for 2.2 Vp Scale Wheels | CarterFab | Tires and Wheels | 0 | 04-01-2014 09:32 AM |
Project "working class superduty" true scale | Diesel-tech | 1.9 Scale Rigs | 10 | 05-21-2011 09:36 PM |
| |