10-02-2019, 11:48 AM | #1 |
Pebble Pounder Join Date: Dec 2013 Location: NorCal
Posts: 170
| Lengthening SCX24
I briefly saw this talked about in 1 post, but nothing more concrete. What are the extra links and half shaft for that came with the SCX24? I believe someone said they were to make it longer. Which end? And where? Thanks. |
Sponsored Links | |
10-02-2019, 11:54 AM | #2 |
I wanna be Dave Join Date: Feb 2007 Location: South FL
Posts: 3,349
| Re: Lengthening SCX24
They are to shorten the wheelbase. I forget the exact numbers, but a few mm longer than a Barrage. Closer to the Carisma MSA1-E Sent from my Pixel 3 XL using Tapatalk |
10-02-2019, 12:08 PM | #3 |
I wanna be Dave Join Date: Jul 2014 Location: Deep South
Posts: 3,444
| Re: Lengthening SCX24
Is it in the manual?
|
10-02-2019, 12:18 PM | #4 |
I wanna be Dave Join Date: Feb 2007 Location: South FL
Posts: 3,349
| Re: Lengthening SCX24 |
01-12-2020, 09:31 PM | #5 |
Pebble Pounder Join Date: Dec 2013 Location: NorCal
Posts: 170
| Re: Lengthening SCX24
Ok, so.... I just got the longer links. Someone told me my rear end of the deadbolt is already longer? But the kit I can use in the front to make it longer? I have the Deadbolt |
01-13-2020, 05:40 AM | #6 |
Let me 3D Print that... Join Date: Jun 2007 Location: Concord
Posts: 315
| Re: Lengthening SCX24
If you have the Deadbolt and bought the links for the Jeep, you can stretch the front wheelbase by 10mm. You need the links for the Jeep in order to get the longer upper Y link unless you are planning on doing the 4-link mod which will require custom links anyway. You will need to make the front driveshaft longer as well.
|
01-13-2020, 05:51 AM | #7 |
Pebble Pounder Join Date: Dec 2013 Location: NorCal
Posts: 170
| Re: Lengthening SCX24
I did get the whole kit. It does make it way longer. To the point my servo hits the bumper. |
01-13-2020, 10:28 AM | #8 |
Let me 3D Print that... Join Date: Jun 2007 Location: Concord
Posts: 315
| Re: Lengthening SCX24
Yes. Everything is packaged pretty tight up front. Moving stuff around usually requires modifying something.
|
01-13-2020, 12:14 PM | #9 |
Pebble Pounder Join Date: Dec 2013 Location: NorCal
Posts: 170
| Re: Lengthening SCX24
I put it back the way I had it.
|
01-13-2020, 01:15 PM | #10 |
RCC Addict Join Date: Mar 2012 Location: Under a Rock in North Texas
Posts: 1,389
| Re: Lengthening SCX24 It's possible you need the Jeep JL front bumper, as the upper shock mounts seem to be made into it. I'm not certain what the differences are, but I'd be willing to bet that's part of it. I ordered the JL front bumper, lengthening kit, and rear bumper w/ hinge. Should have it sometime next week so I can comment then. Also, it may be time for someone to design a chassis mount for the servo. |
01-13-2020, 01:41 PM | #11 |
Pebble Pounder Join Date: Dec 2013 Location: NorCal
Posts: 170
| Re: Lengthening SCX24
one thing I did notice, is the ES09md is longer in body. so even in a stock mount, it is very far forward.... does the shapeways mount move the back of the servo further back over the pumpkin, or does it make it stick so far out?
|
01-13-2020, 02:04 PM | #12 |
Let me 3D Print that... Join Date: Jun 2007 Location: Concord
Posts: 315
| Re: Lengthening SCX24
The one I sell for the Micro Shark conversion pushes it back a couple of mm. That is designed for the ES08 though. Not sure how the ES09 compares dimensionaly.
|
01-13-2020, 05:28 PM | #13 |
Pebble Pounder Join Date: Dec 2013 Location: NorCal
Posts: 170
| Re: Lengthening SCX24 |
Lengthening SCX24 - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Lengthening the wheelbase | AreCee | Axial SCX-10 | 15 | 08-21-2009 08:25 PM |
slash wb lengthening? | 0778drz110 | Non Crawler RC's | 23 | 07-02-2008 10:45 AM |
XC lengthening tut?? | waluu | Newbie General | 2 | 05-21-2008 09:50 AM |
chassis lengthening | firstumustcrawl | General Crawlers | 7 | 07-20-2004 06:22 PM |
Lengthening a TXT | ultralord | Tamiya Txt-1 and Juggernaut | 12 | 05-23-2004 11:02 PM |
| |