Extradition The purpose of this truck is to go anywhere the big bad brushless trucks can go and then get them out when they get stuck. Using Wk axles and axial transmission, keeping her as light as possible,(to save axle shafts)Gpm 70 mm aluminum shocks, 1/8" x2" x 26" homebrew chassis. Also using the stock 5" Wk tires in the rear and 2.2 Tsl's up front for a slight Overdrive on the front. How she sits now. http://i1240.photobucket.com/albums/...psxcfi7jth.jpg Next shock towers. |
Re: Extradition The shock towers were built then deleted, suspension is completed and trans is in. I need to make some spacers and get some longer screws to get the trans motor plate on. Chassis is being painted yellow. Body will be metallic navy blue with yellow highlights. |
Re: Extradition Back together.http://i1240.photobucket.com/albums/...ps71y7dlse.jpg |
Re: Extradition |
Re: Extradition |
Re: Extradition |
Re: Extradition I narrowed the cab a full 1inch and put a bed together. Yes that is a 2.2 Scx10 on the back.http://i1240.photobucket.com/albums/...ps7urdbhog.jpghttp://i1240.photobucket.com/albums/...psjtv9klsz.jpg |
Re: Extradition Mockup for my driver. He will sit a bit lower but not much.http://i1240.photobucket.com/albums/...pslziq92z9.jpg http://i1240.photobucket.com/albums/...psxrmtss7s.jpg |
Re: Extradition you have it looking good so far, keep it going. |
Re: Extradition Quote:
Doors are in, hinged using tape right now.http://i1240.photobucket.com/albums/...psuqcsxz1n.jpghttp://i1240.photobucket.com/albums/...psww3tdeej.jpg And the steering is in. Solar d772.http://i1240.photobucket.com/albums/...psjox07vry.jpg |
Re: Extradition Took her for a spin in the living room today. Crawls good, just need to finish the cab/bed, mount them and mount the electronics. Getting excited about driving it. |
Re: Extradition I knocked out a battery mount in the saddle position. http://i1240.photobucket.com/albums/...ps0smcolsr.jpg http://i1240.photobucket.com/albums/...psij8lppyv.jpg Going to run this body tomorrow.http://i1240.photobucket.com/albums/...psmig2efje.jpg |
Re: Extradition Got her out.http://i1240.photobucket.com/albums/...psnmzlkjed.jpghttp://i1240.photobucket.com/albums/...pszkfveibj.jpghttp://i1240.photobucket.com/albums/...ps28s4weyj.jpghttp://i1240.photobucket.com/albums/...psmgovazcb.jpg http://i1240.photobucket.com/albums/...psaiudpjwb.jpg And the carnage.http://i1240.photobucket.com/albums/...psiijjevzo.jpg |
Re: Extradition Thoughts, she needs more power. She is very stable but rear heavy, the center axle was poping in bound situations and the skid was flexing under load. She is still geared to high, motor got to the point that I couldn't hold my finger on it. ESC was hot to. In hill climbs (loose sand) the ESC shut off a few times. She needs some improvements for sure but that is the fun, right? |
Re: Extradition New drive train setup.http://i1240.photobucket.com/albums/...psihwt4ka4.jpg |
Re: Extradition Threw her on a scale today, 7.5 lbs rtr. 10 lbs with the toolbox and tools. |
Re: Extradition Picked this up today.http://i1240.photobucket.com/albums/...pslb1zrk0e.jpg |
Re: Extradition Not digging my cab. I saw a Mack Terra Pro cement truck on the road, and I think I am going to copy the cab.http://i1240.photobucket.com/albums/...psrlwelnfx.jpg In other news I found some old beadlocks rings, I painted them silver, and mounted them on the axial rims http://i1240.photobucket.com/albums/...psfhbl45bt.jpg |
Re: Extradition I think I stripped a gear in the middle axle on Sunday. She won't climb a hill without "popping". Need to tear her apart clean her up and inspect the axle. I am going to put the build on hold for a while, going to Finish the F650 and my Pig mud truck and my Cc01. |
Re: Extradition |
All times are GMT -6. The time now is 03:49 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com