Just got my HG-P601 6x6 Crawler Well, I finally got my 6x6. My story was the same as most others. Trying to get all the parts together, kits to expensive, unable to build a styrene body, yada yada yada.... I got mine through GearBest.com and it took a total of about 13 days to get here from China. I have also ordered up a bunch of upgrades as well like metal chassis rails. I linked all the parts I've been getting on my website at FourDogsRC.com. I'll upload some videos into the video section. I did an unboxing video as well as an out-of-the-box running video. http://i1298.photobucket.com/albums/...ps9vunahcg.jpg http://i1298.photobucket.com/albums/...psvfvmvpcl.jpg Some Box Pics of the Details http://i1298.photobucket.com/albums/...psbqvd76ok.jpg http://i1298.photobucket.com/albums/...ps55kujqcy.jpg http://i1298.photobucket.com/albums/...pshtpqcyaw.jpg The battery *meh* (doesn't last long) http://i1298.photobucket.com/albums/...psekmefxbx.jpg The remote Control. Has a switch to control the 2 speed servo as well. This will be an upgrade coming soon. http://i1298.photobucket.com/albums/...psvfvmvpcl.jpg Out of the box and un-wrapped http://i1298.photobucket.com/albums/...psg7h1ocbx.jpg Top off. I like how the trans/motor is set up. In its first run, I was getting no torque twist. http://i1298.photobucket.com/albums/...psnf7zpe31.jpg Also pretty nice having a frame mounted steering servo out of the box. http://i1298.photobucket.com/albums/...ps0zxlwlsn.jpg The metal brace that attaches the third axle. http://i1298.photobucket.com/albums/...psye07o71l.jpg The underside http://i1298.photobucket.com/albums/...psjysmqkpg.jpg Pic outside with my TwinHammer http://i1298.photobucket.com/albums/...psuggrwgxq.jpg Rear axle lock-outs (with bushings) http://i1298.photobucket.com/albums/...pso2awmcdb.jpg Axle gearbox with stock grease. (Actually has more grease than some of my higher end rigs from factory) http://i1298.photobucket.com/albums/...psmbdto9uc.jpg Another downside, the shafts are 4mm as opposed to the normal 5mm http://i1298.photobucket.com/albums/...ps9u5pivta.jpg Axial body sitting on frame to see how the WB lines up. http://i1298.photobucket.com/albums/...psdke535km.jpg Stock 2.2 Wheel/Tire. Not very soft and not much rubber. It's like having 21" wheels on the truck. http://i1298.photobucket.com/albums/...psbs4mgffi.jpg These are stock Twin Hammer wheels/tires. I like the look and fit much better. http://i1298.photobucket.com/albums/...pszoptxhhp.jpg |
Needed bearings for Axles and Knuckles Ok, after measuring everything out, it looks like you'll need: - Six 5x9x3mm bearings - Two 4x7x2.5mm bearings per axle On the front knuckles: - Two 5x9x3mm - Two 8x12x3.5mm Should be an end total of 28 bearings to get it going. |
Re: Just got my HG-P601 6x6 Crawler Got her painted up today. Just need to learn led wiring now.... http://images.tapatalk-cdn.com/15/11...a59b5ba2bb.jpg http://images.tapatalk-cdn.com/15/11...6854f7c192.jpg Sent from my iPhone using Tapatalk |
Re: Just got my HG-P601 6x6 Crawler Nice, I like the orange, here is my truck, I bought fully upgraded and find it actually pretty good. http://i154.photobucket.com/albums/s...114_205355.jpg By fully upgraded I mean came with all the options China offered. So I have the built in gear shift. I too plan for a lot of upgrades and will fallow to see how yours turns out. |
Re: Just got my HG-P601 6x6 Crawler If anyone finds metal driveshafts that'll work for truck, please post up a link! They need to have a 4mm inner diameter instead of the normal 5mm inner diameter. |
Re: Just got my HG-P601 6x6 Crawler Well, I'm not sure if this is right, but based on the limited info there is on wiring led lights (for someone who has never done it before) here is my attempt. http://images.tapatalk-cdn.com/15/11...0aabbe9cc4.jpg http://images.tapatalk-cdn.com/15/11...023e12e284.jpg http://images.tapatalk-cdn.com/15/11...9d99c29266.jpg The last photo here is me holding a 3.3v button cell on the wires. I hope when I plug it into the rx, they all don't burn out. That'll be many hours wasted...... Sent from my iPhone using Tapatalk |
Re: Just got my HG-P601 6x6 Crawler Made a little progress today on the lights. http://images.tapatalk-cdn.com/15/11...28dbcdd85f.jpg Sent from my iPhone using Tapatalk |
Re: Just got my HG-P601 6x6 Crawler Quote:
you can cut them up to the right lenght. |
Re: Just got my HG-P601 6x6 Crawler Like to see the orange paintjob, nicely done. Did you somehow clear the windows, made it transparant again? |
Re: Just got my HG-P601 6x6 Crawler Quote:
I used 600 and then 800 grit sandpaper. Once that was done, I used some headlight restore and it got about as clear as I think they are going to get. Sent from my iPhone using Tapatalk |
Re: Just got my HG-P601 6x6 Crawler Oke well nice Job. It looks a lot less toy_ish. (hmm is that a word) Verstuurd vanaf mijn G708 Oc met Tapatalk |
Re: Just got my HG-P601 6x6 Crawler Finally got the light done. Not as bright as I'd like them to be, but I'm not about to tear into them again to redo it. Was a pain in the butt to begin with.... http://images.tapatalk-cdn.com/15/11...3cbab84cf8.jpg http://images.tapatalk-cdn.com/15/11...7640585fb4.jpg https://vimeo.com/146724389 Sent from my iPhone using Tapatalk |
Re: Just got my HG-P601 6x6 Crawler looks good man. I bought the body and put it on a scx10 chassis. https://scontent-iad3-1.xx.fbcdn.net...8a&oe=565730B5 |
Re: Just got my HG-P601 6x6 Crawler Got mine today. Still waiting for the upgraded chassis rails (outrageous flex in the chassis), but surprised for what you get for the price, even with the extra parts and shipping it was under $200. I like the 1.9s better than the 2.2s. I'll probably switch those out, and add paint and lights also. I've got a light module so that won't be too difficult. Probably just need to extend some wires. I did notice the 2spd tranny with the servo mount, but never saw an option on GearBest or Banggood for hooking a servo to it. Note: William Kline - Dead FB URL. "URL has expired" |
Re: Just got my HG-P601 6x6 Crawler Body does not fit on the Beast II chassis. The rear wheels are too close together on the Beast. Leads on the battery are crap. They pulled out the second time I tried to connect. Switching the ESC to Deans and using a different battery. Added a light kit too. |
Re: Just got my HG-P601 6x6 Crawler |
Re: Just got my HG-P601 6x6 Crawler I found it for $96 bucks and pulled the trigger also, ordered the metal chassis to firm it up. Looking forward to receiving it. What LED kit are you running? |
Re: Just got my HG-P601 6x6 Crawler Yup. It was under $100 for the truck, $45 for shipping and about $40 in chassis rails and odds&ends that they had available. I used this one - Light Kit - I thin the price has jumped since I bought it or there are other brand names, but essentially the same 12 LED kit for under $15 that has a controller for flashing sequences. I'll start my thread soon so I don't highjack FD's here. |
Re: Just got my HG-P601 6x6 Crawler Hi i carshed my 6x6 and now my reverse is not workin can any one tell me how to fix it plus were is the best place for upgrades thank 07539327064 |
Re: Just got my HG-P601 6x6 Crawler Parts for these can be ordered at gearbest or banggood. Also seen a few on fleabay. The stock esc and radio system is a 2 in 1 so keep that in mind if you replace either one |
All times are GMT -6. The time now is 04:29 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com