|
| LinkBack | Thread Tools | Display Modes |
06-25-2017, 01:08 PM | #1 |
I wanna be Dave Join Date: Jun 2017 Location: Humboldt county
Posts: 4,475
| Stand alone winch system with its own BEC?
I'm working on a winch setup for my TRX-4 and the most straight forward way to do it is with the wireless controllers due to the transmitter setup. I also chose an SSD OX winch which is 3s capable. The wireless controller I chose (HeyOk) is said to be 3s capable but I've read their comments about it "Yes, 3S lipo is good. Don't take the input voltage much over 12." Which makes me want to include a BEC to keep the voltage right at 12. This setup will use a little 850mah 3s battery just for this winch. Which leads me to my question, I plan on using a CC BEC 2.0 I have lying around to limit the voltage to 12V, but I'm a bit uncertain on how to properly hook this up when its a separate system. I'm guessing id just used either of the red and black wires or maybe even tie them together (More amps?). This BEC has 2 leads that go to the receiver, one is power and ground and the other has power, ground and signal. This seems safe to me but id love to get some other folks input -Thanks |
Sponsored Links | |
06-25-2017, 04:16 PM | #2 |
RCC Addict Join Date: Jun 2016 Location: Germany
Posts: 1,364
| Re: Stand alone winch system with its own BEC?
both are outputs. the one with additional signal is to connect castle link for programming. Gesendet von meinem T1-A21L mit Tapatalk |
06-27-2017, 08:46 AM | #3 |
I wanna be Dave Join Date: Jun 2017 Location: Humboldt county
Posts: 4,475
| Re: Stand alone winch system with its own BEC?
Well I got all the parts and I'll be assembling it this evening, let me know if this is the wrong method.
|
06-27-2017, 09:58 AM | #4 | |
RCC Addict Join Date: Aug 2008 Location: Paulina
Posts: 1,213
| Re: Stand alone winch system with its own BEC?
From Robert in another thread. The 2 outputs are the same but basically there to add more accessories or share the load of a higher amp draw. You should be fine using either lead to power the winch or using both as they are both tied in on the BEC board together. Are you allowing the ESC to continue to power the Rx? Quote:
| |
06-27-2017, 03:26 PM | #5 |
I wanna be Dave Join Date: Jun 2017 Location: Humboldt county
Posts: 4,475
| Re: Stand alone winch system with its own BEC? Yes the ESC still powers the receiver. The BEC will only have the winch connected to it. Ah, I see now that quote is from Robert@Castle, I'm just getting used to seeing folks from the industry posting on here, very cool! Thanks for the input calcagno45 and Magic_yeti Last edited by HumboldtEF; 06-27-2017 at 03:30 PM. |
06-28-2017, 06:23 PM | #6 |
I wanna be Dave Join Date: Jun 2017 Location: Humboldt county
Posts: 4,475
| Re: Stand alone winch system with its own BEC?
Just to update the thread all went as planned no issues. Wiring is as follows: 3s battery to cc 2.0 BEC, one of its outputs (minus signal) to HeyOk wireless controller, HeyOk output to winch |
Tags |
bec, heyok wireless, winch |
Stand alone winch system with its own BEC? - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Commando Winch System & 3Racing winch motor upgrade! | Locked Up | Locked Up RC | 17 | 03-27-2015 08:09 AM |
Commando Winch System & 3Racing winch motor upgrade! | Locked Up | Vendors Electronics | 1 | 11-04-2014 07:59 AM |
using a CC BEC for onboard charging system | 12voltfun | Electronics | 3 | 12-22-2010 03:56 PM |
Goat System & BEC ? | moto | Newbie General | 1 | 12-22-2008 07:24 AM |
Thread Tools | |
Display Modes | |
| |