| |
| |||||||
 |
| | LinkBack | Thread Tools | Display Modes |
04-05-2019, 12:48 AM
| #1 |
| Newbie Join Date: Jul 2009 Location: Misano Adriatico, Italy
Posts: 13
|  Correct driver/figurine height for 1/10 = 7"?
I want to buy a driver figure for my 1/10 Jeep Wrangler body but I'm concerned about the sizing. Is 7"/17-18cm correct for this scale? Cheers, Tom. |
|  |
| Sponsored Links | |
| | |
|
04-05-2019, 06:02 AM
| #2 |
| Quarry Creeper Join Date: Mar 2014 Location: san antonio
Posts: 492
| Re: Correct driver/figurine height for 1/10 = 7"?
I believe so. Anything smaller than that starts to look odd and anything larger may not fit. This guy before I chopped his legs off measured about 6.8” and looks as scale as I could find in a short timeframe.  Sent from my iPhone using Tapatalk |
|
| |
|
04-05-2019, 08:58 AM
| #3 |
| I wanna be Dave Join Date: Dec 2006 Location: here
Posts: 3,042
| Re: Correct driver/figurine height for 1/10 = 7"?
Sorcca rules for a full figure head to toe 5.5" minimum for scale points.
Last edited by tapped-out; 04-05-2019 at 09:01 AM. |
|
| |
|
04-05-2019, 09:07 AM
| #4 |
| Rock Crawler Join Date: Dec 2018 Location: Ontario, Canada
Posts: 697
| Re: Correct driver/figurine height for 1/10 = 7"?
Yes, 7" will be good for 1/10 scale. You can probably go a touch shorter as well, but much taller could be a challenging fit.
|
|
| |
|
04-05-2019, 09:26 AM
| #5 |
| I wanna be Dave Join Date: Oct 2010 Location: Caldwell ID.
Posts: 4,328
| Re: Correct driver/figurine height for 1/10 = 7"?
A 7" figure scaled up from 1/10 scale would be 70" tall. aka 5'10" so average man height.
|
|
| |
|
04-05-2019, 09:27 AM
| #6 |
| Newbie Join Date: Jul 2009 Location: Misano Adriatico, Italy
Posts: 13
| Re: Correct driver/figurine height for 1/10 = 7"?
Thanks for the replies. 18cm Deadpool it is then, however, I may have to amputate his lower legs. How do I stop them growing back? Tom. |
|
| |
|
04-05-2019, 10:57 AM
| #7 |
| Newbie Join Date: Mar 2019 Location: A cornfield, IA, USA
Posts: 27
| Re: Correct driver/figurine height for 1/10 = 7"?
Speaking of drivers and stuff, does anyone know of a good wide seat? I've got a crash bandicoot figure, and his shoulders and upper body are fairly wide while his lower body is pretty narrow.
|
|
| |
|
Correct driver/figurine height for 1/10 = 7"? - Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Dying Light 3d printable figurine | 4wd4ws | Chit Chat | 1 | 01-17-2015 03:02 PM |
| Hyundai no driver commercial "Empty Car Convoy" | STANG KILLA SS | Chit Chat | 6 | 07-03-2014 06:31 PM |
| <iframe width="420" height="315" src="//www.youtube.com/embed/gYr-dbPEOnE" frameborde | boolean21 | Scale Videos! | 0 | 10-01-2013 09:39 AM |
| rckjeep's "Ralph" TLT Tuber in RC Driver | JasonInAugusta | Chit Chat | 16 | 06-16-2005 07:19 PM |
| Thread Tools | |
| Display Modes | |
| |
Linear Mode
