|
| LinkBack | Thread Tools | Display Modes |
01-19-2017, 03:03 PM | #1 |
I wanna be Dave Join Date: Mar 2013 Location: Minden
Posts: 2,198
| Look at what I just bought
I found this Tamiya TA-01 Idemitsu Motion Mugen Civic for less than $100 And thinking about turning it into a Rally car or a Pre-Runner truck, cause they are pretty much the same platform I'm going to check it out and see if I can get it ripping again Last edited by kgb424; 12-11-2018 at 01:12 AM. |
Sponsored Links | |
01-19-2017, 08:35 PM | #2 |
I wanna be Dave Join Date: Mar 2013 Location: Minden
Posts: 2,198
| Re: Look at what I just bought
I love old shit like this R/C From my online research the body was released in 1993 that makes its 24 years old and was on a different R/C The Chassis is TA02 from Stadium Racer Series which was the Chevy S-10 or the Ford F150 or the Toyota Pre-Runner They were released in 1994/1995, so that makes the chassis 22 years old Just shows these things are bad ass Last edited by kgb424; 01-19-2017 at 08:52 PM. |
01-19-2017, 09:05 PM | #3 |
~THE SCALE SHOP~ Join Date: Apr 2006 Location: KILLEEN TX
Posts: 10,056
| Re: Look at what I just bought
sell to EeePee for $200
|
01-19-2017, 09:18 PM | #4 |
I wanna be Dave Join Date: Mar 2013 Location: Minden
Posts: 2,198
| Re: Look at what I just bought
I found some Bling Bling In my parts stock pile They need glued but might hook up Or slide around under power I like the rims Last edited by kgb424; 12-11-2018 at 01:11 AM. |
01-19-2017, 09:32 PM | #5 |
I wanna be Dave Join Date: Mar 2013 Location: Minden
Posts: 2,198
| Re: Look at what I just bought
Really Does EeePee know about these So I could ask him questions about the R/C |
01-20-2017, 03:34 PM | #6 |
I wanna be Dave Join Date: Mar 2013 Location: Minden
Posts: 2,198
| Re: Look at what I just bought
I love my stock pile, its got a little of bit of everything I got 2 different brushless setups to use in the TA02 I got the Vanguard 2900kv and the Vanguard AE3 on 2S and a Castle 3800kv and a SCT MMP to run 3's The setups are for my unfinished and lost interest in Axial EXO I being wanting a Street/Rally/Drift R/C for awhile now Last edited by kgb424; 12-11-2018 at 01:11 AM. |
01-20-2017, 04:32 PM | #7 |
I wanna be Dave Join Date: Mar 2013 Location: Minden
Posts: 2,198
| Re: Look at what I just bought
And I just found a new side project for my HPI Mini Desert Trophy Truck Cause lets be honest it sucks as a off road and short course truck, it fills full of dirt and always runs hot and the suspension travel or lack of is a joke And I replaced all the bearings and all new CVD's in the axles and new CVD drive lines It better off set up as Rally Car or Street and maybe drifting baby I like it, it looks like a simple and easy mod too make it Rally friendly Last edited by kgb424; 12-11-2018 at 01:11 AM. |
01-20-2017, 05:51 PM | #8 |
~THE SCALE SHOP~ Join Date: Apr 2006 Location: KILLEEN TX
Posts: 10,056
| Re: Look at what I just bought |
01-21-2017, 12:33 AM | #9 |
I wanna be Dave Join Date: Mar 2013 Location: Minden
Posts: 2,198
| Re: Look at what I just bought
That was easy and it didn't take that long too convert the Mini Trophy Is now almost ready for its new life as a Rally/Street with the right tires Its been a few years since I ran the Mini Trophy I can't remember how the battery tray works and where the ESC mounts I will look online and see if I can figure it out Last edited by kgb424; 12-11-2018 at 01:11 AM. |
01-22-2017, 03:15 PM | #10 |
I wanna be Dave Join Date: Mar 2013 Location: Minden
Posts: 2,198
| Re: Look at what I just bought
I found 2 sets of these Axial 1.9'' wheels and the offset is close to the original HPI Mini Trophy wheels that they will work for me, and were in my stock pile, The HPI ones, I had to remove the old tires and foams using acetone and letting them soak overnight and it took off the silver paint that was on the wheels They look better white, more of a Rally/Street look and with the beadlock rings, it gives them a different look then the normal Rally/Touring style wheel Been looking at Rally and Touring car tires, too see if I can find some with a little more side way to raise the Mini Trophy up a little Last edited by kgb424; 12-11-2018 at 01:11 AM. |
01-23-2017, 11:00 PM | #11 |
I wanna be Dave Join Date: Mar 2013 Location: Minden
Posts: 2,198
| Re: Look at what I just bought
WTF I put the original Tamiya TA02 wheels in some Acetone to remove some old rubber and some old glue And the Acetone ate all four wheels and turned them into a plastic paste I have never had wheels melt in Acetone before That was crazy, guess I'm buying some more wheels Wonder if it has happened to other people You can see what they look like before they melted Last edited by kgb424; 12-11-2018 at 01:11 AM. |
01-24-2017, 02:57 AM | #12 |
I wanna be Dave Join Date: Mar 2013 Location: Minden
Posts: 2,198
| Re: Look at what I just bought
Do you need to use a servo saver ?? Can I use a different steering arm ?? Anybody here know how many teeth the Tamiya steering servo saver has I tried a Futaba servo and a waterproof Traxxas servo and the saver just spins of the servo shaft even the screw in and tight So I must of stripped out the servo saver or it's the servo's have the wrong number of teeth and that's why it stripped out I'm going to look online and see what I can find out Last edited by kgb424; 01-24-2017 at 03:05 AM. |
01-24-2017, 10:45 AM | #13 | |
Newbie Join Date: Apr 2016 Location: Chile
Posts: 42
| Re: Look at what I just bought Quote:
Acetone kill plastic..... If you wanna remove glue, grease, etc use wd40.... acetone is very toxic.... | |
01-24-2017, 12:04 PM | #14 |
I wanna be Dave Join Date: Mar 2013 Location: Minden
Posts: 2,198
| Re: Look at what I just bought
Still looking for the number of teeth for the servo saver, I found the servo saver its on the C parts tree I did find this, it tells which holes to use, for the teeth on the pinion gear, it sets the mesh correctly for you The more I look online the more I like the TA02, its was the shit in its day Can anybody tell me, what does Part B3 do and is it necessary, its looks like it slides of the pinion shaft OK Part B3 is a gauge you use to set the spacing between the motor and pinion So the pinion is aligned with the spur gear You can see the numbers on the motor mount Last edited by kgb424; 12-11-2018 at 01:11 AM. |
01-24-2017, 12:59 PM | #15 |
No idea what I'm doing Join Date: Oct 2008 Location: Underground, CO
Posts: 4,529
| Re: Look at what I just bought |
01-24-2017, 01:24 PM | #16 |
I wanna be Dave Join Date: Mar 2013 Location: Minden
Posts: 2,198
| Re: Look at what I just bought
I figured it out The original kit came with 2 different servo savers The one I got is for a Sanwa, Acoms, JR, Ko it won't work The second one is for a Futaba and Tamiya that's the one I need I'm going to just put a normal steering arm on Last edited by kgb424; 12-11-2018 at 01:11 AM. |
01-25-2017, 11:38 PM | #17 |
I wanna be Dave Join Date: Mar 2013 Location: Minden
Posts: 2,198
| Re: Look at what I just bought
Tore down the TA02 and cleaned out all of the old grease out of the plastic gears and the diff's and the housings I installed a Traxxas 2075 water proof servo with a Axial aluminium steering arm Then bench tested it, and every thing seems ok, its got a lot of drag on the drive line I am going to order a bearing kit for it, cause the plastic bushing are worn and maybe some new gear sets and a aluminuim motor mount Also found a extra set of drivers from a Mini Trophy, and need to make a interior and figure how to mount them to the body or maybe the chassis Need smaller battery packs cause my 5000 MAH punch packs are too big to fit in the chassis, need to look at lipo pack sizes and order a couple of the right sized ones Last edited by kgb424; 12-11-2018 at 01:11 AM. |
01-27-2017, 01:20 AM | #18 |
I wanna be Dave Join Date: Mar 2013 Location: Minden
Posts: 2,198
| Re: Look at what I just bought
I painted the beadlock rings on the HPI wheels with the closet matching paint. I could find It's Tester Florescent Orange, going to shoot some Flat Lacquer over the wheel once the paint cures a little Also drywall taped and Shoo-Goo'ed the inside of the body going to paint some Flat White Over the Shoo-Goo, cause you can see the drywall tape when held up to the light The body is already getting stiff, it needs to setup and cure then painted My camera is giving the orange a pink tint on the body I like it looks good to me Last edited by kgb424; 12-11-2018 at 01:11 AM. |
01-27-2017, 10:15 PM | #19 |
I wanna be Dave Join Date: Mar 2013 Location: Minden
Posts: 2,198
| Re: Look at what I just bought
You know its almost cheaper to buy a Hard Body instead of a Lexan body, cause a lot of them the sticker sheets are sold separately I found this complete Sand Scorcher Body for less then $40 Need to decide to slam it to the ground like a drifter Or lift a little and give it the Rally look, and still drive it on the street I also found 2 different VW flat fours one is single carb, the other one is dual carbs And I found a very exspensive Flat Six Porsche motor I like the dual carbs motor the best Last edited by kgb424; 12-11-2018 at 01:10 AM. |
01-28-2017, 12:44 AM | #20 |
I wanna be Dave Join Date: Mar 2013 Location: Minden
Posts: 2,198
| Re: Look at what I just bought
I found these Sand Scorchers 2 are slammed to the ground The other are lifted and using small offroad tires I'm really like the slammed to ground ones Cause slow and low is the tempo And just cruise the Vista Baby Last edited by kgb424; 12-11-2018 at 01:10 AM. |
Look at what I just bought - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Built not bought, with a bunch of things I bought. | imthatguy | Axial SCX-10 | 28 | 01-10-2016 08:41 PM |
bought fx-r | troy95chevy | Electronics | 13 | 08-23-2011 12:17 PM |
Anybody bought a new JK lately? | Harley | Chit Chat | 3 | 02-21-2009 12:29 AM |
Look what i just bought........ | mxracer525 | Tamiya TLT Crawlers | 7 | 06-17-2007 10:07 AM |
who bought this? | OIT_TLT | Chit Chat | 5 | 01-24-2007 12:24 PM |
| |