| |
07-22-2019, 10:13 PM
| #1 |
| Newbie Join Date: Jan 2017 Location: FR
Posts: 20
|  My XV-01
After reading turtle's XV-01 thread, I decided to build my own Lancia Delta. It will be a mixed on/off road with two kind of bodies. I have all the pieces (I hope) and I slowly started the building. For the moment I'm at the slipper clutch stage :    Sent from my Redmi Note 7 Pro using Tapatalk |
|  |
| Sponsored Links | |
| | |
|
07-27-2019, 11:31 AM
| #2 |
| Newbie Join Date: Jan 2017 Location: FR
Posts: 20
| Re: My XV-01
Some steps forward :            Sent from my Redmi Note 7 Pro using Tapatalk |
|
| |
|
09-17-2019, 06:37 AM
| #3 |
| Newbie Join Date: Sep 2019 Location: Diamond Creek
Posts: 2
| Re: My XV-01
Hey hows the build going? Ive just ordered an XV01 looking forward to building it up Will be stock to start with |
|
| |
|
09-30-2019, 11:46 AM
| #4 | |
| Newbie Join Date: Jan 2017 Location: FR
Posts: 20
| Re: My XV-01 Quote:
I stopped the build for the moment I have to find the "inspiration"  I already know that a big headache is waiting for me when I'll have to put electronics in it. Envoyé de mon Mi 9T Pro en utilisant Tapatalk | |
|
| |
|
10-22-2019, 01:12 PM
| #5 |
| Newbie Join Date: Jan 2017 Location: FR
Posts: 20
| Re: My XV-01
Update : after changing the position of the engine and successfully tested the electronics (which gave me a headache  ), I mounted the wheels on the chassis and made a little driving test. Unfortunately I cannot understand why the car behaves like a traction, I have 0.001% propulsion on the rear axle. I checked the belt and the pulleys and everything seems OK, but as soon as there is any resistance (just a finger on the rear tires) I have no power in the back. Do you have any hints? I thought of a big difference of oil in the gears of the differentials (I forgot the references but basically more dense in the front)    |
|
| |
|
10-22-2019, 05:22 PM
| #6 |
| I wanna be Dave Join Date: Sep 2011 Location: Douglassville, PA
Posts: 4,224
| Re: My XV-01
Sounds like there is a cross pin missing somewhere.....
|
|
| |
|
10-23-2019, 11:10 AM
| #7 | |
| Newbie Join Date: Jan 2017 Location: FR
Posts: 20
| Re: My XV-01 Quote:
 | |
|
| |
|
10-25-2019, 04:15 PM
| #8 | |
| I wanna be Dave  Join Date: Jan 2006 Location: Corruptifornia
Posts: 12,107
| Re: My XV-01
OP you're off to a good start, looking forward to more rally goodness!  Quote:
| |
|
| |
|
10-26-2019, 04:06 AM
| #9 |
| Newbie Join Date: Jan 2017 Location: FR
Posts: 20
| Re: My XV-01
I found: the two pulleys tended to get loose because I had not pressed the two plastic pieces NN24 and 13 enough (it was so hard that I thought I'd break them). Thus there was no place to properly insert the circlip in his seat: as there was traction the exagon of the pulley came out of the small iron pin BA and therefore no more traction. Now I have tightened plastic pieces but I hope that the two e-rings will hold (I folded and covered with glue once installed). Thank you all for your advices ... I will surely bother you again ... Now I'm fighting with the servo direction that I can not adjust correctly ( too much right or left )   |
|
| |
|
10-27-2019, 03:28 PM
| #10 |
| Newbie Join Date: Jan 2017 Location: FR
Posts: 20
| Re: My XV-01
Painting the body    |
|
| |
|
11-04-2019, 09:34 AM
| #11 |
| Newbie Join Date: Jan 2017 Location: FR
Posts: 20
| Re: My XV-01
Reinforcing the body with shoegoo and aluminum tape  |
|
| |
|
11-10-2019, 12:50 PM
| #12 |
| Newbie Join Date: Jan 2017 Location: FR
Posts: 20
| Re: My XV-01
Decals        Last edited by lucadoc; 11-10-2019 at 12:59 PM. |
|
| |
|
11-15-2019, 01:44 PM
| #13 |
| Newbie Join Date: Jan 2017 Location: FR
Posts: 20
| Re: My XV-01 |
|
| |
|
11-18-2019, 11:08 PM
| #14 |
| Newbie Join Date: Jan 2017 Location: FR
Posts: 20
| Re: My XV-01
.    |
|
| |
|
10-30-2020, 04:19 PM
| #15 |
| Newbie Join Date: Jan 2017 Location: FR
Posts: 20
| Re: My XV-01 |
|
| |
 |
| Thread Tools | |
| Display Modes | |
| |
Linear Mode
