Re: Wreckluse Feedback, Support & FAQ
 

for the motor, I have a holmes hobby 35T with a BR-XL on 3S...very good...

I actually craked the hood too, the HPI jeep is a direct fit? I know it's kinda sucky to scrap a complete body for the hood...but I think it might be cheaper to get the body from my hobbyshop than ordering a new hood from RCP ;) no offence Sozo, but with the shipping to Canada...

Re: Wreckluse Feedback, Support & FAQ
 

I'm running a HH 35T/Sidewinder/3S combo, great low end control and good wheel speed when I drop the hammer "thumbsup"

Re: Wreckluse Feedback, Support & FAQ
 

I run a 35t

Re: Wreckluse Feedback, Support & FAQ
 

I guess a 55T will be too slow

Re: Wreckluse Feedback, Support & FAQ
 

if your running a 3 cell lipo it will work fine

Re: Wreckluse Feedback, Support & FAQ
 

I have a 27 turn stock motor in mine , its a little bit fast but I also run 32 pitch gears 58 spur 15 pinion , I can slow it down with gearing when I need to , my second one will have a 55 t in it .

Re: Wreckluse Feedback, Support & FAQ
 

Can you guys post pics of how you mount your electronics?

Re: Wreckluse Feedback, Support & FAQ
 

all my electornics are mounted behind my dash....battery slides in behind the front wheels

I also have an issue with the servo arm hitting the 4 link truss. Have you experienced this?

Re: Wreckluse Feedback, Support & FAQ
 

i got mine put together last night now i just need to get a new hood!

http://i1281.photobucket.com/albums/...pse5eadb95.jpg

http://i1281.photobucket.com/albums/...ps1145ce05.jpg

Re: Wreckluse Feedback, Support & FAQ
 

is it mounted to the chassis or the axle?

We'll meet up this week

Mine is chassis mounted

Re: Wreckluse Feedback, Support & FAQ
 

post a pic ....maybe we can figure something out

Re: Wreckluse Feedback, Support & FAQ
 

Ok I really need some help

Here are my link measurement. (actual link not eye to eye)

Upper 115mm Front
Upper 109mm Rear

Lower 109mm Front
Lower 93mm Rear

Here is a pic.

Look at the servo arm right on the 4 link mount

http://i1054.photobucket.com/albums/...ps7d3c25d3.jpg

Here is a shot of where the servo suppose to go and the 4 link mount is right at it

http://i1054.photobucket.com/albums/...ps768d7395.jpg

I have also tried a GCM mount which is not as high but its still hitting.

What are my options, it seems I cant get axle mounted as the tabs on my axles is cutoff. I am thinking getting new links but not so sure.....

Re: Wreckluse Feedback, Support & FAQ
 

I see some custom fabrication.... you may want to flip the servo so the arm points forward
and cut away some more from the front

Re: Wreckluse Feedback, Support & FAQ
 

Shes a runner!! I shaved off some of the 4 link truss and mounted the servo arm forward. It only hits on the left side. I am thinking of adding some spacers to the servo when I mount it to give me more clearance.

Re: Wreckluse Feedback, Support & FAQ
 

Cool work around Natski...post up some pics of that if you can...

Re: Wreckluse Feedback, Support & FAQ
 

Yes will post pic soon. I actually worked on it again and replaced the 4 link truss with the stock Axial 4 link mount (it sits lower on the axle). I also used some servo post to mount the servo higher and cut out some of the metal so the servo arm moves freely. It works better this way as I get more clearance.

Re: Wreckluse Feedback, Support & FAQ
 

Just wanted to let you know guys... HPI discontinued the Rubicon body #7182...dont break you hoods!

Re: Wreckluse Feedback, Support & FAQ
 

Will this be available again?