Axial RECON Ultra 4 G6 at King of the Hammers

[Trump1]

Originally Posted by jerry2575

Remember what the event doesn't matter because the adventurist class is still walking pace because it is adventure not a race.

Thanks Jerry. This will be my first KOH and second G6, but I think I get the point now.

[DRIVNMF]

Originally Posted by Trump1

I need help deciding on what gearing to run at the King of the Hammers. Should I gear up for more speed or keep it low?

I would appreciate any insight. Thanks.

That is such a fine line. A 1.9 G-Ride needs some wheel speed for loose climbs, sled pulling, and during the Holidays; throwing mash taters in the air.

The Training wheel classes or the 2.2's, not so much, because the larger tire size helps clear stage obstacles.

I run a 35t with a 60t spur and 14t pinion. 32p for durability. That combo works great for me.

Mike Pham, runs a brushless system. Wheel speed is great when you need it and it crawls very well too.

Originally Posted by jerry2575

Remember what the event doesn't matter because the adventurist class is still walking pace because it is adventure not a race.

You are correct, but wheel speed in a G6 is needed. I have watched your G-Ride pull a toyota which was pulling a jeep, through the mud pit!

That would not have been achieved on a 55t 80t spur, 14t pinion!

Do work, Stage Detective!

[jerry2575]

Originally Posted by DRIVNMF

That is such a fine line. A 1.9 G-Ride needs some wheel speed for loose climbs, sled pulling, and during the Holidays; throwing mash taters in the air.

The Training wheel classes or the 2.2's, not so much, because the larger tire size helps clear stage obstacles.

I run a 35t with a 60t spur and 14t pinion. 32p for durability. That combo works great for me.

Mike Pham, runs a brushless system. Wheel speed is great when you need it and it crawls very well too.




You are correct, but wheel speed in a G6 is needed. I have watched your G-Ride pull a toyota which was pulling a jeep, through the mud pit!

That would not have been achieved on a 55t 80t spur, 14t pinion!

Do work, Stage Detective!

I run a 35t with a 3s with 14 pin. The best advice to give is you want your motor to stay under 160 degrees. When in need of more speed, volt up and gear down instead of increasing the pinion size. Info: Brushed Motor Selection and Gearing Guide by Vehicle | The Search for Power

[Erin]

Originally Posted by jerry2575

I run a 35t with a 3s with 14 pin. The best advice to give is you want your motor to stay under 160 degrees. When in need of more speed, volt up and gear down instead of increasing the pinion size. Info: Brushed Motor Selection and Gearing Guide by Vehicle | The Search for Power

This why Im hoping a 25t at 5:1 will give me both wo the heat

[Agama]

I love my Pro 4 with RX8 and RC4WD 2 speed tranny!

Crawls great and hauls.

[jerry2575]

Is it time yet!

[The Doc]

Originally Posted by jerry2575

Is it time yet!

NO!!!!! my trucks not done

[jerry2575]

Originally Posted by The Doc

NO!!!!! my trucks not done

Build faster!

[ROLANDROCKSHOP]

so jealous right now....

ill make it out there someday...


Ya'll get sum G6 KOH action!!!

[Cpt Nemo]

Axial RECON Ultra 4 G6 Driver List

Early registration is available here; RECON G6 Registration Thread

Copy and Paste your Driver List intel

Check here for Class Descriptions; Axial RECON Ultra 4 G6 at King of the Hammers


(Name / Screen Name / G-Ride / Tires & Foams / Favorite Ultra 4 Racer)



Ultra 1.9

1. Mike Pham / nissan_driver24 / Axial scx10 Honcho / Flat Irons w stock foams / Robbie Gordon
2. Erin Fick / erin / Axial scx10 honcho / Pitbulls w CI foams / Rocking J
3.
4.
5.
6.
7.
8.
9.
10.


Ultra 2.2

1. John Askar / Krawlr4life / U4 Thug Buggy / PitBulls RBI II / Shannon Campbell
2.
3.
4.
5.
6.
7.
8.
9.
10.


Adventurist 1.9

1. Cole Bailey / Unibomber / R&D Fab Class 6 / Pit Bull & Stock / Robbie Gordon
2. Mike Duncan / THE DOC / SCX-TF2 / PITBULLS @ MAYHEMS / CAMPBELL
4. NICK DUNCAN / SCX 10 / PITBULLS / PRO-LINES / ROBBIE GORDON
5. Jerry Ellifritz / Jerry2575 / Scx10 / pit bull CI foams/ Shannon Campbell
6. Eric Jr. / SCX10 Tacoma/ Proline Flat Irons/
7. Eric Sr. / Trump1 / SCX10 Toyota "ROCRUNR" / Pit Bull RB /
8. Jason Wilson / HB_CRAWLER / SCX10 / Pit Bulls CI foams / Robbie Gordon
9. Jacob Hogue/ Rckhrse/ SCX10/ Swampers/ Campbell
10. Chris Goris / brokennib/SCX10/ IRock CI foams / Gordon
11. Kevin Muck/ Cpt Nemo/SCX10 VP Comanche/ Ripsaws/ ????
12.
13.
14.
15.
16.
17.
18.
19.
20.


Adventurist 2.2 (Wraith and 2.2 tire class)

1. Brad Bailey / Chasinbaja / Poochie, Axial Wraith / 2.2 Pit Bull RB II's, CI Nova's / Erik Miller
2. Dennis Hogue/ Rochrse/ Proline Hammers/ Campbell
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.


RECON G6 Teams

1. Team R.O.T.R. - R. Parker / N. Telles / Lil' Lexus Axial scx10 / 1.9 Pit Bulls w Lil Nova's / Shannon Campbell
2.
3.
4.
5.
6.
7.
8.
9.
10.

[boostamante]

Stupid question but here goes...

My scaler has Axial axles and Trans but is not an off the shelve rig, am i still allowed to run so logn as i meet noted requirements of 5 scale items?

thanks!

Looking forward to attending and participating seeing as ill be there for the Team Naxja/ Petty Cash EMC race.

[Trump1]

Originally Posted by DRIVNMF

That is such a fine line. A 1.9 G-Ride needs some wheel speed for loose climbs, sled pulling, and during the Holidays; throwing mash taters in the air.

The Training wheel classes or the 2.2's, not so much, because the larger tire size helps clear stage obstacles.

I run a 35t with a 60t spur and 14t pinion. 32p for durability. That combo works great for me.

Mike Pham, runs a brushless system. Wheel speed is great when you need it and it crawls very well too.




You are correct, but wheel speed in a G6 is needed. I have watched your G-Ride pull a toyota which was pulling a jeep, through the mud pit!

That would not have been achieved on a 55t 80t spur, 14t pinion!

Do work, Stage Detective!

DMFer,

"Wheel speed for loose climbs" was my concern. At the G6 Mountain Mash I had some trouble with loose dirt. Ironically, it was the trail marker that I had suggested.

I thought I would ask about gearing, since I'm not familiar with the KOH terrain. I'm running a 12T with a stock spur (4. I think I have a 14T laying around somewhere, maybe a little more speed wouldn't hurt.

Originally Posted by Agama

I love my Pro 4 with RX8 and RC4WD 2 speed tranny!

Crawls great and hauls.

Agama,

I have been thinking about a two (2) speed transmission for my next build. I'm undecided ... waffling at the moment. I'll have to decide when I start ordering parts sometime in the Spring.

[rangair94]

Originally Posted by boostamante

Stupid question but here goes...

My scaler has Axial axles and Trans but is not an off the shelve rig, am i still allowed to run so logn as i meet noted requirements of 5 scale items?

thanks!

Looking forward to attending and participating seeing as ill be there for the Team Naxja/ Petty Cash EMC race.

Yup. There are some custom built rigs that run G6s, don't forget the tow strap.

[Agama]

Originally Posted by Trump1

Agama,

I have been thinking about a two (2) speed transmission for my next build. I'm undecided ... waffling at the moment. I'll have to decide when I start ordering parts sometime in the Spring.

The two speed tranny is awesome! I now own three of them. I'm running one in my son's Wraith with a 35T brushed motor and it's great! Crawls really well and has pretty good wheel speed. Nothing like my Pro4.

[DRIVNMF]

Originally Posted by boostamante

Stupid question but here goes...

My scaler has Axial axles and Trans but is not an off the shelve rig, am i still allowed to run so logn as i meet noted requirements of 5 scale items?

thanks!

Looking forward to attending and participating seeing as ill be there for the Team Naxja/ Petty Cash EMC race.

Boostamante, there's never a stupid question if you don't know the answer. You are good to go.

We will see you getting your scaler fix at the Axial RECON Ultra 4 G6!

Originally Posted by Trump1

DMFer,

"Wheel speed for loose climbs" was my concern. At the G6 Mountain Mash I had some trouble with loose dirt. Ironically, it was the trail marker that I had suggested.

I thought I would ask about gearing, since I'm not familiar with the KOH terrain. I'm running a 12T with a stock spur (4. I think I have a 14T laying around somewhere, maybe a little more speed wouldn't hurt.

You will encounter sand, rock, more sand, & more rock.

Wheel speed is important, but there is a balance between crawlability and turf terrorizing wheel speed.

Try different pinions, but watch for excessive heat.

I hope this helps. Do Work, G6'er!

[Cheatin]

Ok, got the day off, I'm down for the stoner's pace class, running is what you do from the cops, not for exercise. Cops are still "0" btw...



Axial RECON Ultra 4 G6 Driver List

Early registration is available here; RECON G6 Registration Thread

Copy and Paste your Driver List intel

Check here for Class Descriptions; Axial RECON Ultra 4 G6 at King of the Hammers


(Name / Screen Name / G-Ride / Tires & Foams / Favorite Ultra 4 Racer)



Ultra 1.9

1. Mike Pham / nissan_driver24 / Axial scx10 Honcho / Flat Irons w stock foams / Robbie Gordon
2. Erin Fick / erin / Axial scx10 honcho / Pitbulls w CI foams / Rocking J
3.
4.
5.
6.
7.
8.
9.
10.


Ultra 2.2

1. John Askar / Krawlr4life / U4 Thug Buggy / PitBulls RBI II / Shannon Campbell
2.
3.
4.
5.
6.
7.
8.
9.
10.


Adventurist 1.9

1. Cole Bailey / Unibomber / R&D Fab Class 6 / Pit Bull & Stock / Robbie Gordon
2. Mike Duncan / THE DOC / SCX-TF2 / PITBULLS @ MAYHEMS / CAMPBELL
4. NICK DUNCAN / SCX 10 / PITBULLS / PRO-LINES / ROBBIE GORDON
5. Jerry Ellifritz / Jerry2575 / Scx10 / pit bull CI foams/ Shannon Campbell
6. Eric Jr. / SCX10 Tacoma/ Proline Flat Irons/
7. Eric Sr. / Trump1 / SCX10 Toyota "ROCRUNR" / Pit Bull RB /
8. Jason Wilson / HB_CRAWLER / SCX10 / Pit Bulls CI foams / Robbie Gordon
9. Jacob Hogue/ Rckhrse/ SCX10/ Swampers/ Campbell
10. Chris Goris / brokennib/SCX10/ IRock CI foams / Gordon
11. Kevin Muck/ Cpt Nemo/SCX10 VP Comanche/ Ripsaws/ ????
12. Anthony "Cheatin" Cabigao/SCXbasedF-Toy/Motoworx-California cut Trepadors CI foams, no favorite driver I'd sleep with all of them.
13.
14.
15.
16.
17.
18.
19.
20.


Adventurist 2.2 (Wraith and 2.2 tire class)

1. Brad Bailey / Chasinbaja / Poochie, Axial Wraith / 2.2 Pit Bull RB II's, CI Nova's / Erik Miller
2. Dennis Hogue/ Rochrse/ Proline Hammers/ Campbell
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.


RECON G6 Teams

1. Team R.O.T.R. - R. Parker / N. Telles / Lil' Lexus Axial scx10 / 1.9 Pit Bulls w Lil Nova's / Shannon Campbell
2.
3.
4.
5.
6.
7.
8.
9.
10.

[axelsnapr]

Just got the green light! SOCAL is gunna re-schedule the feb comp so members can attend. So count me in for "Ultra 2.2 class".

My CUSTOM Roksloth chassis, RCP loaded AX10 drivetrain, 2s Novak Goat, Proline Swampered Ultra4 rig is ready to DO-WORK!

Axial RECON Ultra 4 G6 Driver List

Early registration is available here; RECON G6 Registration Thread

Copy and Paste your Driver List intel

Check here for Class Descriptions; Axial RECON Ultra 4 G6 at King of the Hammers


(Name / Screen Name / G-Ride / Tires & Foams / Favorite Ultra 4 Racer)



Ultra 1.9

1. Mike Pham / nissan_driver24 / Axial scx10 Honcho / Flat Irons w stock foams / Robbie Gordon
2. Erin Fick / erin / Axial scx10 honcho / Pitbulls w CI foams / Rocking J
3.
4.
5.
6.
7.
8.
9.
10.


Ultra 2.2

1. John Askar / Krawlr4life / U4 Thug Buggy / PitBulls RBI II / Shannon Campbell
2. Jerry Tobin / Axelsnapr / SDF Ultra4 / Proline Super Swampers PL memory / Jason Pickett (of course)
3.
4.
5.
6.
7.
8.
9.
10.


Adventurist 1.9

1. Cole Bailey / Unibomber / R&D Fab Class 6 / Pit Bull & Stock / Robbie Gordon
2. Mike Duncan / THE DOC / SCX-TF2 / PITBULLS @ MAYHEMS / CAMPBELL
4. NICK DUNCAN / SCX 10 / PITBULLS / PRO-LINES / ROBBIE GORDON
5. Jerry Ellifritz / Jerry2575 / Scx10 / pit bull CI foams/ Shannon Campbell
6. Eric Jr. / SCX10 Tacoma/ Proline Flat Irons/
7. Eric Sr. / Trump1 / SCX10 Toyota "ROCRUNR" / Pit Bull RB /
8. Jason Wilson / HB_CRAWLER / SCX10 / Pit Bulls CI foams / Robbie Gordon
9. Jacob Hogue/ Rckhrse/ SCX10/ Swampers/ Campbell
10. Chris Goris / brokennib/SCX10/ IRock CI foams / Gordon
11. Kevin Muck/ Cpt Nemo/SCX10 VP Comanche/ Ripsaws/ ????
12. Anthony "Cheatin" Cabigao/SCXbasedF-Toy/Motoworx-California cut Trepadors CI foams, no favorite driver I'd sleep with all of them.
13.
14.
15.
16.
17.
18.
19.
20.


Adventurist 2.2 (Wraith and 2.2 tire class)

1. Brad Bailey / Chasinbaja / Poochie, Axial Wraith / 2.2 Pit Bull RB II's, CI Nova's / Erik Miller
2. Dennis Hogue/ Rochrse/ Proline Hammers/ Campbell
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.


RECON G6 Teams

1. Team R.O.T.R. - R. Parker / N. Telles / Lil' Lexus Axial scx10 / 1.9 Pit Bulls w Lil Nova's / Shannon Campbell
2.
3.
4.
5.
6.
7.
8.
9.
10.

[axelsnapr]

Hey guys can you please add this driver to the Ultra4 list. I pasted his info. Thanks


"....can you put me on the sign up sheet. heres my info: Sean Dauster, rocksloth, chassis SDF Outlaw ultra4, and rc4wd twoface....... Thanx"


Axial RECON Ultra 4 G6 Driver List

Early registration is available here; RECON G6 Registration Thread

Copy and Paste your Driver List intel

Check here for Class Descriptions; Axial RECON Ultra 4 G6 at King of the Hammers


(Name / Screen Name / G-Ride / Tires & Foams / Favorite Ultra 4 Racer)



Ultra 1.9

1. Mike Pham / nissan_driver24 / Axial scx10 Honcho / Flat Irons w stock foams / Robbie Gordon
2. Erin Fick / erin / Axial scx10 honcho / Pitbulls w CI foams / Rocking J
3.
4.
5.
6.
7.
8.
9.
10.


Ultra 2.2

1. John Askar / Krawlr4life / U4 Thug Buggy / PitBulls RBI II / Shannon Campbell
2. Jerry Tobin / Axelsnapr / SDF Ultra4 / Proline Super Swampers PL memory / Jason Pickett (of course)
3. Sean Duaster / Rocksloth / SDF Outlaw Ultra4 / RC4WD Twoface /
4.
5.
6.
7.
8.
9.
10.


Adventurist 1.9

1. Cole Bailey / Unibomber / R&D Fab Class 6 / Pit Bull & Stock / Robbie Gordon
2. Mike Duncan / THE DOC / SCX-TF2 / PITBULLS @ MAYHEMS / CAMPBELL
4. NICK DUNCAN / SCX 10 / PITBULLS / PRO-LINES / ROBBIE GORDON
5. Jerry Ellifritz / Jerry2575 / Scx10 / pit bull CI foams/ Shannon Campbell
6. Eric Jr. / SCX10 Tacoma/ Proline Flat Irons/
7. Eric Sr. / Trump1 / SCX10 Toyota "ROCRUNR" / Pit Bull RB /
8. Jason Wilson / HB_CRAWLER / SCX10 / Pit Bulls CI foams / Robbie Gordon
9. Jacob Hogue/ Rckhrse/ SCX10/ Swampers/ Campbell
10. Chris Goris / brokennib/SCX10/ IRock CI foams / Gordon
11. Kevin Muck/ Cpt Nemo/SCX10 VP Comanche/ Ripsaws/ ????
12. Anthony "Cheatin" Cabigao/SCXbasedF-Toy/Motoworx-California cut Trepadors CI foams, no favorite driver I'd sleep with all of them.
13.
14.
15.
16.
17.
18.
19.
20.


Adventurist 2.2 (Wraith and 2.2 tire class)

1. Brad Bailey / Chasinbaja / Poochie, Axial Wraith / 2.2 Pit Bull RB II's, CI Nova's / Erik Miller
2. Dennis Hogue/ Rochrse/ Proline Hammers/ Campbell
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.


RECON G6 Teams

1. Team R.O.T.R. - R. Parker / N. Telles / Lil' Lexus Axial scx10 / 1.9 Pit Bulls w Lil Nova's / Shannon Campbell
2.
3.
4.
5.
6.
7.
8.
9.
10.

[Quiel]

Do we have a fixed location?

[VP Dan]

going to try and make this one and hammer down. team vp at hammertown