Super 300 CVD's

[The Violator]

Originally Posted by Cruzin Illusion

Is there a date on when they will be shipped to the vendors?

Originally Posted by JamisonWorkshop

Any word on when these are getting out to Vendors. Anxiously waiting.

Originally Posted by Failedabortion

Ordered mine on the 20th also, still not here...Maybe I'll stick with tcs from now on...

Originally Posted by JamisonWorkshop

Still looking for word on ETA. Anything ????

Originally Posted by hoppa

X3

I am the first guy to slam someone who does not live up to what I think is their end of a bargain. BUT, superdave is a class guy who I don't think spends as much time on crawler as everyone else. I don't think he is personally making the cvd's so everyone is at the mercy of his machinist. And as most of us know, the only worse person to be at the mercy of would be an automotive painter, and maybe a wife. He will let everyone know when they are ready. Have patience my young Padawan's. He will come through. And they are worth the wait.

[SDS Customz]

I want to address one issue that i have found first. In the first gen. shafts the pin retainers where not heat treated, thus allowing the pins to dent the sleeves and walk out of one side of the cvd cup. the fix is to install heat treated rings with a hand ground pin that is .012 longer. To my knowledge there has only been 5 pins broken via this issue. To me and those 5 customers that is not exceptable. down time and loss of faith in what is supposed to be a bombproof product has to be eliminated.

the new rings and pins will be available within 10-14 days through the vendors via the rebuild kits that everyone has been asking about. the rebuilds will come with 4pins 4 sleeves and 2 barrels(no bearings to keep the cost down) they should be around 30 bucks or so from the vendors.

with that said the ever present question of ETA. This morning 45 sets are being shipped to TCS and hopefully by the end of the week I can fill the rest of the TCS order and be shipping to the rest of the vendors. As some have said, I am at the mercy of the machinists, he is also at mine as I am dropping off almost half of the shafts i recieved on Friday for small QC issues. I will fill orders in the order they where placed to me.

thanks for everyones patience!!! I will post as the shipments are shipped. I will try and get the vendors to put up pre-orders for the rebuild kits. PRE-ORDER them so they will order larger numbers and have plenty of stock for everyone.

All of the shafts that are shipping today have the V2 pins and rings.

[bbyrd22]

[JamisonWorkshop]

Thank you very much. All I need to hear.

Glad they will be even better when I recieve them as well.

[1beatjeep]

Originally Posted by SDS Customz

I want to address one issue that i have found first. In the first gen. shafts the pin retainers where not heat treated, thus allowing the pins to dent the sleeves and walk out of one side of the cvd cup. the fix is to install heat treated rings with a hand ground pin that is .012 longer. To my knowledge there has only been 5 pins broken via this issue. To me and those 5 customers that is not exceptable. down time and loss of faith in what is supposed to be a bombproof product has to be eliminated.

the new rings and pins will be available within 10-14 days through the vendors via the rebuild kits that everyone has been asking about. the rebuilds will come with 4pins 4 sleeves and 2 barrels(no bearings to keep the cost down) they should be around 30 bucks or so from the vendors.

with that said the ever present question of ETA. This morning 45 sets are being shipped to TCS and hopefully by the end of the week I can fill the rest of the TCS order and be shipping to the rest of the vendors. As some have said, I am at the mercy of the machinists, he is also at mine as I am dropping off almost half of the shafts i recieved on Friday for small QC issues. I will fill orders in the order they where placed to me.

thanks for everyones patience!!! I will post as the shipments are shipped. I will try and get the vendors to put up pre-orders for the rebuild kits. PRE-ORDER them so they will order larger numbers and have plenty of stock for everyone.

All of the shafts that are shipping today have the V2 pins and rings.

Are these for the axial knuckle 300 to that you are sending out today

[slip408]

Sweet deal just placed my order with TCS...

[XJ Farmer]

Good to hear, it looks like I need to jump on the Super 300 bandwagon. I'm finally sick of breaking the stockers, a repair cost me a win at our local comp this weekend. I thing I'm on my 12th replacement. Thanks for being so good to us and for making such a bomb proof product

Later

Farmer

[Hoppa]

SAAWEEEET!!!!!!
Thanks for the update.
Sounds like I bought from the right vendor.

[SDS Customz]

Originally Posted by 1beatjeep

Are these for the axial knuckle 300 to that you are sending out today

I dont think that any of the vendors have any left. if in question, here is how u tell. the rings that aren't heat treated are shiny, the heat treated ones are dulled and spotty. So as far as i know, u only need the rebuild kits if already have super 300 shafts. though a kit in the tool box never hurts.

[4xFord]

Originally Posted by SDS Customz

In the first gen. shafts the pin retainers where not heat treated, thus allowing the pins to dent the sleeves and walk out of one side of the cvd cup. the fix is to install heat treated rings with a hand ground pin that is .012 longer.

Well that is just my luck that it happened to me twice. I had to flip the ring around to put the dented side on the other end of the shaft. Not bashing the product though, you are a great vendor with incredible service. Thanks again Superdave.

[1beatjeep]

Originally Posted by SDS Customz

I dont think that any of the vendors have any left. if in question, here is how u tell. the rings that aren't heat treated are shiny, the heat treated ones are dulled and spotty. So as far as i know, u only need the rebuild kits if already have super 300 shafts. though a kit in the tool box never hurts.

I dont have the 300 yet, been waiting for the one for the axial knuckles that is why i was asking because no one has the 300 for the axial knuckles in stock. so that is why i asked if you sent out any axial 300 out to the vendors


Thanks

[SDS Customz]

sorry misunderstood the question. the long answer is that yes i sent some of TCS's order out only to discover tonight that I had to call him and have the 45 sets shipped back. a friend brought it to my attention that a bearing that previously had no fit issues now has an inconsistent fit.

So again I will have to appologize for the delays. But I do appreciate all of the input that EVERY one has given me on the product. This product is only here because, we where all tired of our junk breaking. that said I dont want any of my products causing more issues for the end user.

So for those of u waiting, unfortunetely the wait will be slightly longer. Agian my apologies, i just want to make a product that everyone can enjoy hassle-free for a long time to come!!!

[joesbruiser]

Originally Posted by SDS Customz

sorry misunderstood the question. the long answer is that yes i sent some of TCS's order out only to discover tonight that I had to call him and have the 45 sets shipped back. a friend brought it to my attention that a bearing that previously had no fit issues now has an inconsistent fit.

So again I will have to appologize for the delays. But I do appreciate all of the input that EVERY one has given me on the product. This product is only here because, we where all tired of our junk breaking. that said I dont want any of my products causing more issues for the end user.

So for those of u waiting, unfortunetely the wait will be slightly longer. Agian my apologies, i just want to make a product that everyone can enjoy hassle-free for a long time to come!!!

You sir are a great standup guy

[BigBlackCummins]

Originally Posted by SDS Customz

sorry misunderstood the question. the long answer is that yes i sent some of TCS's order out only to discover tonight that I had to call him and have the 45 sets shipped back. a friend brought it to my attention that a bearing that previously had no fit issues now has an inconsistent fit.

So again I will have to appologize for the delays. But I do appreciate all of the input that EVERY one has given me on the product. This product is only here because, we where all tired of our junk breaking. that said I dont want any of my products causing more issues for the end user.

So for those of u waiting, unfortunetely the wait will be slightly longer. Agian my apologies, i just want to make a product that everyone can enjoy hassle-free for a long time to come!!!

A excellent vendor with awesome support, who could ask for more!

[JamisonWorkshop]

Thanks for making sure everything is right before we get them though. I know after waiting a month for them and then if I were to find out that something was wrong after all that it would not be fun.

Good thing I got a moonbuggy to put together while I wait.

[binaryterror]

Originally Posted by XJ Farmer

I'm finally sick of breaking the stockers, a repair cost me a win at our local comp this weekend.

Nah your driving on course 2 after the repair sealed that 3rd place

:flip off:

[XJ Farmer]

Oh well atleast I beat you at Worlds and the State comp


Later
Farmer

[SDS Customz]

should have the box back from tcs first of the week, Im assembling the replacments, so I should be able to simply turn the box around and send it back right away, so shafts will again be out to the ever so patient consumer shortly!!!

thanks guys

[SDS Customz]

Finally:For everyone that has been patient, parts are shipping. 60 sets left for TCS on friday morn. CKRC's should ship on monday afternoon. U should all start seeing them shortly after the holiday

[BigBlackCummins]

You rock Dave!!

Now I'm going to just sit and wait by the mailbox...