|
| LinkBack | Thread Tools | Display Modes |
02-23-2013, 02:38 PM | #1 |
Pebble Pounder Join Date: Sep 2009 Location: Norway
Posts: 129
| Bolt on`s Berg Superjuice Setup: From what I have read on rccrawler Axles: Rcbros lightweight Berg locker Berg axles with homemade tubes and servo Mount Knuckle weights and link monts from D-lux Motors: Team Brood Apocalypse 45T HHK ESC's: 2x Holmes Hobbies BR-XL BEC's: 2x Castle Creations BEC 10A Servo's: 2x Hitec HS7980TH Battery: Thunder Power 850 Mah 65C Transmitter: Futaba 4PKS Chassis: Team Y-Town Crawlers Delrin Superjuice Wheels: HPI Homemade rims Tires: Hot Bodies Sedona 7,5" Homemade Shocks: Traxxas Big Bore 4" Axial rod ends Links: Made by moses670 This is the first super that I have built, need good advice for improvements. Thanking jeremyH for help and advice. Will be testing this when the snow is gone and some komps in Norway before I run superCrawler in Germany. Stein |
Sponsored Links | |
02-23-2013, 04:55 PM | #2 |
Quarry Creeper Join Date: Feb 2011 Location: Germany
Posts: 227
| Re: Bolt on`s Berg Superjuice
Rig and Knuckle Weight System Looks very good. See you at the Supercrawl
|
02-23-2013, 06:23 PM | #3 |
Pebble Pounder Join Date: Sep 2009 Location: Norway
Posts: 129
| Re: Bolt on`s Berg Superjuice |
02-23-2013, 06:35 PM | #4 |
I wanna be Dave Join Date: Sep 2005 Location: Houston, TX
Posts: 16,952
| Re: Bolt on`s Berg Superjuice
That turned out nicely! You are gonna LOVE driving these big trucks! |
02-24-2013, 02:19 AM | #5 | |
Pebble Pounder Join Date: Sep 2009 Location: Norway
Posts: 129
| Re: Bolt on`s Berg Superjuice Quote:
I adjusted the drag break, but there is sound in a motor. Adjusted it down to 30%, but heard a weak sounds from the motor. Removes Holms hold and the sound disappears. Motor and ecs are new, do I need to check this more? Adjusted both at 60%. Stein | |
02-24-2013, 03:22 AM | #6 |
Quarry Creeper Join Date: Feb 2011 Location: Germany
Posts: 227
| Re: Bolt on`s Berg Superjuice
Thats the normal sound of Holmes Hold, .I have mine set at 40% with 45T Holmes Motors. fritz |
02-24-2013, 05:52 AM | #7 |
Pebble Pounder Join Date: Sep 2009 Location: Norway
Posts: 129
| Re: Bolt on`s Berg Superjuice |
02-24-2013, 06:10 AM | #8 |
I wanna be Dave Join Date: Sep 2005 Location: Houston, TX
Posts: 16,952
| Re: Bolt on`s Berg Superjuice
I have mine set pretty low as well (IIRC, 40%). Are you checking the motor buzzing at idle on a flat surface with no transmitter input? That Holmes Hold will cause the motors to buzz under load, but should be silent at idle.
|
02-24-2013, 10:23 AM | #9 | |
Pebble Pounder Join Date: Sep 2009 Location: Norway
Posts: 129
| Re: Bolt on`s Berg Superjuice Quote:
The motor is quiet when I start to throttle. Is quite weak, well maybe it is ok. But it is not completely silent, you see the armature go back and forth | |
02-24-2013, 03:28 PM | #10 |
I wanna be Dave Join Date: Sep 2005 Location: Houston, TX
Posts: 16,952
| Re: Bolt on`s Berg Superjuice
That is strange....that's not how it works on my truck. I believe the way the Holmes Hold works is to reverse the direction of the motor just a slight amount. Perhaps your throttle trim is not set exactly at zero?
|
02-28-2013, 12:15 PM | #11 |
Pebble Pounder Join Date: Sep 2009 Location: Norway
Posts: 129
| Re: Bolt on`s Berg Superjuice
If not idle throttle is at zero, would not this problem been on both motors?
|
02-28-2013, 01:07 PM | #12 |
I wanna be Dave Join Date: Oct 2008 Location: Sumter
Posts: 6,141
| Re: Bolt on`s Berg Superjuice
The Holmes Hold is an "active hold" so it will pulse the motor in both directions at a very high frequency if I remember correctly. It will cause a buzz and what you are describing sounds fine.
|
02-28-2013, 01:52 PM | #13 | |
Pebble Pounder Join Date: Sep 2009 Location: Norway
Posts: 129
| Re: Bolt on`s Berg Superjuice Quote:
Thanks for the reply. Were just afraid that electronics would be damaged as the motors did not behave in the same way. Stein | |
03-18-2013, 10:37 PM | #14 |
RcBros Hobbies Join Date: Nov 2005 Location: Oregon
Posts: 4,646
| Re: Bolt on`s Berg Superjuice
Any chance you can snap a picture of how the rear of the servo is mounted? Looking for ideas lol. Thanks
|
03-19-2013, 04:04 PM | #15 |
Rock Crawler Join Date: May 2012 Location: Australia
Posts: 517
| Re: Bolt on`s Berg Superjuice |
03-19-2013, 05:09 PM | #16 |
RcBros Hobbies Join Date: Nov 2005 Location: Oregon
Posts: 4,646
|
The "rear" of the servo, not the "rear" of the rig ;)
|
03-20-2013, 12:40 PM | #17 |
Pebble Pounder Join Date: Sep 2009 Location: Norway
Posts: 129
| Re: Bolt on`s Berg Superjuice
Rear edge of servo is attached to a bracket that is attached by a screw into housing of the gearbox. Drilled and threaded hole in the gearbox and cut screw so it does not touch the gears. Hope that was how you meant by your question. |
03-20-2013, 01:48 PM | #18 |
RcBros Hobbies Join Date: Nov 2005 Location: Oregon
Posts: 4,646
|
Thank you, I appreciate it!
|
05-20-2013, 02:04 PM | #19 |
Rock Crawler Join Date: Oct 2010 Location: Switzerland
Posts: 579
| Re: Bolt on`s Berg Superjuice
Nice Driving at the Supercrawl Stein congrats 3rd is awesome result for your first big Comp |
05-22-2013, 01:11 PM | #20 | |
Pebble Pounder Join Date: Sep 2009 Location: Norway
Posts: 129
| Re: Bolt on`s Berg Superjuice Quote:
Thank you Manu, it was totally unexpected that it would be so good. Thought breaking competition after all 4 wheels parted, but thanks to Samuli that helped me repair them .. Stein | |
Bolt on`s Berg Superjuice - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Superjuice Berg | 4xFord | Superclass Crawlers | 188 | 11-23-2023 06:52 PM |
Diamond's Superjuice Berg Build | Diamond D | Superclass Crawlers | 220 | 05-03-2016 01:14 PM |
krawls superjuice berg | krawlfreak | Superclass Crawlers | 285 | 03-06-2012 07:23 PM |
krawls superjuice berg | krawlfreak | Videos! | 14 | 02-14-2010 07:14 PM |
| |