super time

[CREEPERBOB]

Originally Posted by CM9000

soo, whats next??? are you going to trace the flange for the short side and just make it longer? or could you use some old long tubes and just machine them? curious to what your plans are.

I've got a couple super Bully axles and a couple extra tubes as well.
I've did some milling to these flanges trying to get the shape figured out (what cuts to do first) . I've got a few feet of 1" o.d. 7075 aluminum rod to do the final tube work.
Then the 3 feet of grade 5- 1/2" Ti rod but need to finish the tubes before I can get final dimensions for the axle shafts.
As soon as I get something cut that isn't embarrassing I'll post up .

[CREEPERBOB]

More stuff. Waiting on a couple FXR's and 45 turn motors.
If I don't get any better results this may turn into a 2.2 pro rig.

[CREEPERBOB]

A little more electronics ,
Ordered 2 @12" x 24" x 2mm and 1 @ 12" x 24" x 2.5mm carbon fiber sheets twill layered 3K.
I have no idea how to cut it yet but hey, gotta try some.

[CM9000]

dremel should work. just wear proper ppe.

[Tom G]

Originally Posted by CREEPERBOB

A little more electronics ,
Ordered 2 @12" x 24" x 2mm and 1 @ 12" x 24" x 2.5mm carbon fiber sheets twill layered 3K.
I have no idea how to cut it yet but hey, gotta try some.

Throw in in the milling machine Hi speed E-mill''s work ok but carbide last a lot longer

[CREEPERBOB]

Originally Posted by CM9000

dremel should work. just wear proper ppe.

Originally Posted by Tom G

Throw in in the milling machine Hi speed E-mill''s work ok but carbide last a lot longer

I ordered a couple Amana 1/8" solid carbide spiral router bit #46260.
I can't get the speed required for these but I'm gonna give them a try.

[richardgarrett56]

These are what u want. Is what i was told form a guy makes tooling bits

[CREEPERBOB]

https://www.amanatool.com/pub/media/.../4/6/46260.jpg
This is what I ordered.

[Tom G]

Originally Posted by CREEPERBOB

I ordered a couple Amana 1/8" solid carbide spiral router bit #46260.
I can't get the speed required for these but I'm gonna give them a try.

Just slow the IPM feed rate down they work just fine

[CREEPERBOB]

This is in addition to the 3 sheets I already received above.
Coming, 2 @14mm x 12mm x 500mm,
2 @ 12mm x 8mm x 500mm, and
2 @ 12mm x 10mm x 500mm carbon fiber roll wrapped tube and a sheet of 1.5mm x 200mm x 500mm twill weave carbon fiber.

Have no idea what will surface from this.

[CM9000]

Originally Posted by CREEPERBOB

This is in addition to the 3 sheets I already received above.
Coming, 2 @14mm x 12mm x 500mm,
2 @ 12mm x 8mm x 500mm, and
2 @ 12mm x 10mm x 500mm carbon fiber roll wrapped tube and a sheet of 1.5mm x 200mm x 500mm twill weave carbon fiber.

Have no idea what will surface from this.

a graphene battery wielding super????

[CREEPERBOB]

Man that boat from China is slow.

[CREEPERBOB]

This thread is a bust , just not enough time.
I do have most of a MOA comp rig though, may be in the classifieds shortly .

[tapped-out]

That's to bad you'd probably enjoy the super... wish I had one.

[CREEPERBOB]

Originally Posted by tapped-out

That's to bad you'd probably enjoy the super... wish I had one.

Yeah, I've had a couple Super Bully rigs and they ARE the shizit .

[CREEPERBOB]

Well, my brand new 2 front Bully 2 axles and 1 used rear bare axle housing lockout to lockout is in the for sale classifieds.
Bob

[CM9000]

I was looking forward to the completion of this.. but other things happen. did you just give up or?

[CREEPERBOB]

Originally Posted by CM9000

I was looking forward to the completion of this.. but other things happen. did you just give up or?

I really did too, to much all the time it seems.
I'll see, maybe no one will buy them huh .

[CM9000]

hopefully you get to keep em. there needs to be more supers and less scalers.

[CREEPERBOB]

:twisted: hmmmm