I enjoy 2.2clod! Nice to meet you.:-P It is writing from Japan. I will refer to the idea of everybody."thumbsup" clod axles HR axletubes, Knuckles, handmade BTA, TTR CVD's, Straights, TAMIYA Modefaid12mmHex's, 7Tpinions mamba25 & enRoute28long-1300, 2set Hyperion servo, DX6i TAMIYA avante2 rearwheels, LOSI claws, http://i34.tinypic.com/29wlssz.jpg http://i34.tinypic.com/1o2e4w.jpg http://i38.tinypic.com/4ryvqw.jpg http://i36.tinypic.com/24gitrr.jpg http://i37.tinypic.com/2hyjwc0.jpg http://i35.tinypic.com/29v11s6.jpg http://i35.tinypic.com/2woaout.jpg |
Good job on those axles, im sure its better clearance than stock, did u burn those? |
Photo miremashita "thumbsup" OIRA ha Comment de Debut desu. www Korega souryou $49.56 no Parts desune. "lixxid" (-人-) namunamu... Sorenishitemo bullhead mo zuibun AROku narimashitane.w TOZAN tanoshimidesu.^^ |
Quote:
sorry,Because English is unskilled Though it doesn't understand whether you can answer neatly The projection of Ledge is cut down. The tape is pasted. http://i35.tinypic.com/2woaout.jpg |
Quote:
TOZAN yorosiku desu"thumbsup" http://i35.tinypic.com/2woaout.jpg |
are dark impact wheels 2.2 ? |
Quote:
I compared it with HPI 2.2wheels. It might be slightly large. sorry,I cannot judge whether to pass the rule. http://i38.tinypic.com/iz6jih.jpg http://i35.tinypic.com/2woaout.jpg |
more narrow http://i36.tinypic.com/1537mlj.jpg Cut off http://i37.tinypic.com/2m4ubs6.jpg http://i37.tinypic.com/30kr8m8.jpg HEXhole is made http://i33.tinypic.com/b3vd6w.jpg Aluminum spacer http://i35.tinypic.com/2ev7vkp.jpg http://i33.tinypic.com/j60d35.jpg http://i38.tinypic.com/5ufecx.jpg Completion! http://i35.tinypic.com/2woaout.jpg |
Looks great! I did something similar with my TTR CVDs! They work quite narrow! Nice crawling spots, BTW. |
Thank you JeremyH! This method, the choice of a wheel increases. But,durability is [ one ] anxious about me. Become single bearing. I run for the time being! Quote:
|
Are those the JP small C tubes and knuckles? If so, then you should be able to still fit both bearings inside. You can see how I narrowed the stance of my 2.2 clod running small C tubes, JP knuckles and TTRs on page 3 of my build thread: http://www.rccrawler.com/forum/tamiya-clod-buster/109709-new-build.html I am running different hexes on mine (14mm losi), but the idea is still the same. |
Thank you JeremyH! I was allowed to see the thread before! Your rig is wonderful! Although I also tried the same method as you at first, Since I was poor at English, acquisition of the wheel was not completed. And I tried how to be different. I will refer to your thread in the future! Quote:
|
Sounds good! Good luck with your build! |
All times are GMT -6. The time now is 04:55 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com