|
CR-01 Setup List I've always wanted to have a consolidated list of vehicle setups for those looking to fine tune their vehicles. Curious if you folks would be interested in contributing to this list. Hopefully we could get it set as a sticky for this forum for the benefit of our community of hobbyist. This template is meant to be organic and should change accordingly with feedback. Here is the template Electronics
Gearing
Suspension
Tires & Wheels
Hop Ups
|
Re: CR-01 Setup List Here is my setup currently. Electronics
Gearing
Suspension
Tires & Wheels
Hop Ups
|
Re: CR-01 Setup List nice setup, how about some pictures. |
Re: CR-01 Setup List |
CR-01 Setup List 1 Attachment(s) Attachment 304213 Electronics Hacked FlySky with 6-channel receiver Holmes BRXL waterproofed HH Crawlmaster 16T on 3S LiPo CC BEC 2x Savox 1210 (waterproof, radio programmed for variable ratio and phase rear steering) Stock gearing and tranny (20T pinion) Suspension Cantilevers all the way, baby! :lmao: Stabilizer Bars - front soft, rear medium (I think) Stock Shocks 30W oil Can't remember which springs I used Tires & Wheels 2.2 Flat Irons on RC4WD 2.2. wagon wheels 2 oz in each front wheel Hop Ups Aluminum side frames Lockers front and rear Reinforced drive shafts and strengthened axles front and rear Aluminum front knuckles (3racing, I believe) Aluminum front servo bed and brackets Carbon mechanism deck Junfac front drive shaft, RC4WD rear drive shaft Wheelbase shortened by ~.5" to get rear wheels closer to centered under wheel well Metal planetary gears Here it is in action: https://www.youtube.com/watch?v=eRSzQFoVJdw&edit=vd |
Re: CR-01 Setup List Electronics Radio - Hobbyking 6ch 2.4ghz ESC - Hobbywing WP-10BL60 unsensored Motor - NTM 2830 PropDrive Outrunner 1000kv Battery - Zippy LiPo 3S 4400mAh (near 3hrs of runtime) Servos - Hobbyking HK15328D Gearing Pinion - 20t (a little slow but crawls very nicely) Suspension Cantilever - no (shocks laid down for minimum droop & max up travel) Stabilizer Bars F/R - no Shocks - STRC shock bodies Springs F/R - Tamiya Short ( Hard-FL, Med-RL & FR, Soft-RR ) Oil Weight - 30? Tires & Wheels Tires - RC4wd 2.2 Mud Slingers (they're pretty, but are not Pitbulls) Wheels - 2.2 beadlock Weighted F - 9oz per tire / R - 6oz per tire Foam - open cell, star cut Hop Ups JBweld in the diff case, no axel pins for lock. Traxxas Universals on steel yokes for drive shafts STRC - front C-hubs & knuckles STRC - straight axle rear conversion STRC aluminum hexes Traxxas wheel nuts (they are serrated) Traxxas Slash waterproof receiver box |
Re: CR-01 Setup List http://osteo.smugmug.com/Cars/CR01/i...41839540-L.jpg Electronics TX - Futaba 3PL RX - R20004GF ESC - Tekin FXR Motor - RC4WD 45T (I think!) Servos - F - HITEC HS646WP, R - Traxxas 2056WP Gearing - stock Pinion - 20T Suspension Cantilever - Gone the way of the dodo bird! Stabilizer Bars - N Shocks - G-Transition 90mm Springs F/R - Full Droop Oil Weight - can't remember what came with the G-Transitions! Tires & Wheels Tires - Flat Irons Wheels - Stock Weighted F/R oz 3.5oz/3.5oz each Beadlocks - Tamiya Aluminum Trimmed Memory Foam Hop Ups Aftermarket curved Lower link arms Aftermarket Al driveshafts (have Tamiya hardened rear) Traxxas Waterproof Electronics case lowered battery tray custom chassis rails (as per OSCR's idea) Current Wish List: Hex Screw Kit Axial Tranny warmer weather to get outside and crawl and test my chassis! |
Re: CR-01 Setup List I'll play! I've got lots of scale rigs, but these two are my favorite. No idea why. Crawling Bug http://i472.photobucket.com/albums/r...pscea37c47.jpg http://i472.photobucket.com/albums/r...psadf0a41f.jpg http://i472.photobucket.com/albums/r...ps0f5183a8.jpg Chassis:
Drivetrain:
Electronics:
Suspension:
Tires & Wheels:
Hop Ups: http://i472.photobucket.com/albums/r...psfe31a15b.jpg Note, I was running Integy garbage C's and Knuckles up front since I got them for $5 a pair, so I stocked up. They held up decently well actually, and got much improved steering. Still have them on the Jeep below. I recently switched over to KM parts for the bug (shown above) - they are super beefy and fit perfect. ........ ...... ..... .... ... CR01 Jeep http://i472.photobucket.com/albums/r...psb495ce4f.jpg http://i472.photobucket.com/albums/r...ps58cd9116.jpg http://i472.photobucket.com/albums/r...psd70b6c90.jpg Chassis:
Drivetrain:
Electronics:
Suspension:
Tires & Wheels:
Hop-ups: http://i472.photobucket.com/albums/r...ps5d8f24ff.jpg ....Cause there's a lot. :) Don't really need any of it, it's just purty. "thumbsup""thumbsup""thumbsup""thumbsup""thumb sup" Number 3 - as of yet unnamed. Not done, but built with leftovers from these 2. Same suspension as the jeep, open diffs and a 3150kv BL motor in at the moment. Not finished, lanquishing in a pile of unfinished aspirations. |
| All times are GMT -6. The time now is 07:20 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com