ROCKEDUP RICKY's 1.9 COMP I have been working on a 1.9 comp rig. Hopefully OKRCRC or NWARC will have a 1.9 class. We plan on having a 1.9 class at Crawlapalooza 09. I started off narrowing the axles. I going with the RCP gears and CVCs in the front. I used a short axle on each side. http://i160.photobucket.com/albums/t...7/DSC02344.jpg http://i160.photobucket.com/albums/t...7/DSC02346.jpg http://i160.photobucket.com/albums/t...7/DSC02348.jpg Here they are ready to go. I had these link mounts off my 1st TLT build. Had to mod them a little but they'll work. Makes them look beefy. http://i160.photobucket.com/albums/t...7/DSC02349.jpg http://i160.photobucket.com/albums/t...7/DSC02347.jpg |
I'm using TCS clocked Cs on the front , so I made this servo mount . http://i160.photobucket.com/albums/t...7/DSC02351.jpg http://i160.photobucket.com/albums/t...7/DSC02352.jpg I made the mount so the servo sits flat after the axle being clocked. Helps to keep the linkage up where it should be. With this mount my linkage sits higher on the face of the punkin, so the linkage will go farther back. It's just a little , but with no dig class you need every little bit you can find. http://i160.photobucket.com/albums/t...7/DSC02354.jpg |
I always put rollers on my rigs, every little bit helps.;-) http://i160.photobucket.com/albums/t...7/DSC02362.jpg All on and feeling smooth. http://i160.photobucket.com/albums/t...7/DSC02364.jpg |
Here's my shot at a chassis. Guys all I have is a steady hand and a dremel tool. Don't make fun. It will change when I get the AKRCC chassis gets done. http://i160.photobucket.com/albums/t...7/DSC02371.jpg http://i160.photobucket.com/albums/t...7/DSC02372.jpg http://i160.photobucket.com/albums/t...7/DSC02373.jpg |
The electronis just fit in this thing. Not a lot of room on a 1.9. http://i160.photobucket.com/albums/t...7/DSC02375.jpg http://i160.photobucket.com/albums/t...7/DSC02376.jpg |
I bought this body along time ago by mistake online. Pushed the wrong button. It's been sitting there for ever. It findly found a home . I left the body a little high, I want to make some 4 inch tall tires ,but not sure what I'm going to make yet. http://i160.photobucket.com/albums/t...7/DSC02377.jpg http://i160.photobucket.com/albums/t...7/DSC02379.jpg http://i160.photobucket.com/albums/t...7/DSC02384.jpg http://i160.photobucket.com/albums/t...7/DSC02382.jpg |
I'll do a little shake down and try to get some action shots or video real soon. |
Looks like a good rig Ricky like your axles mods. |
http://i160.photobucket.com/albums/t...7/DSC02372.jpg I wonder if you could flip the rear axle to get the pinion/driveshaft straighter with the trans output...the link mounts you have would make it pretty easy to do, from the look of it. Was thinking it might free up the rear end a little bit and keep things from binding with the angles you have going there. |
Looks good Rick.. I cut and narrowed some 2.2 Rock claws and they measure 4". I'll probably try another set or tire, as I'm not too keen on the tread design |
Quote:
|
Quote:
|
Quote:
I like the looks of the rig. Body is way cool. Nice choice. "thumbsup" |
Quote:
|
Quote:
|
Quote:
|
Quote:
|
lol!!! what the width and wb? |
Quote:
I could take the width down to 6 3/4, I got some spacers in there now. But this is where I have it for now. I was heading out to give it a run, but it started raining. :-( |
Man you never cease to amaze me. I will have my MRC ready for the comp on the 24th"thumbsup" |
All times are GMT -6. The time now is 08:02 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com