100 Proof FJ-40 Tuber I finally got started on my FJ-40 tuber yesterday and all I have to say is I have a new found respect for the guys that make these. Once you get started though, you get in a rythem and don't want to stop. I based this off one of my favorite FJ-40 buggys, Tom W. (Gunmetalcruz on pirate4x4) 100 Proof Buggy built at Trent Fabrication. Specs TLT Axles (locked w/ wedged spider gear and some JB weld) Team Losi Transmission w/ machine locker and driveshaft flange 2.2 Tires - Mashers 1beatjeep's R/D Customs Aluminum Beadlocks Super Rooster ESC TQ3 Controler & Reciever 55T Lathe w/ 12tooth pinion MG995 Servos Front Dig Traxxas Big Bore Coilovers Wheelbase will bearound 13" - 13.5" I have a neat idea for disconnecting the the rear driveshaft to have front dig but the yokes are back ordered so that will have to wait a few weeks. These first few pics are of the real 100 Proof Buggy 8) http://tamor.us/members-rigs/albums/...9_4_06_048.jpg http://tamor.us/members-rigs/albums/...9_4_06_049.jpg http://tamor.us/members-rigs/albums/..._skins_003.jpg http://tamor.us/members-rigs/albums/..._buggy_094.jpg |
These pics show the progress I made yesterday. Hopefully I can finish it up today, though I will need to take a break and watch A&M beat the hell outa TU "thumbsup" After getting the hang of the whole brazing and bending, I ended up cutting of the front and back and redoing it. Came out 10x's better. I am using 3/16" brakeline for the main chassis and 1/8" solid rod for the bumpers and for using it when I spliced the new ends on. The 1/8" rod fits perfectly into the brakeline, and I also used it in the bottom rockers since I plan on beating this thing hard. I can not believe how well the front bumper came out. The pictures don't do it justice. http://tamor.us/members-rigs/albums/...8/DSC00009.jpg http://tamor.us/members-rigs/albums/...8/DSC00010.jpg http://tamor.us/members-rigs/albums/...8/DSC00012.jpg http://tamor.us/members-rigs/albums/...8/DSC00013.jpg http://tamor.us/members-rigs/albums/...8/DSC00014.jpg http://tamor.us/members-rigs/albums/...8/DSC00015.jpg http://tamor.us/members-rigs/albums/...8/DSC00016.jpg http://tamor.us/members-rigs/albums/...8/DSC00017.jpg http://tamor.us/members-rigs/albums/...8/DSC00018.jpg http://tamor.us/members-rigs/albums/...8/DSC00019.jpg http://tamor.us/members-rigs/albums/...8/DSC00020.jpg |
NICE! i see a few squareness/symetrical probs but not too bad. gonna look cool for sure! are those shock & link mounts stout enough? |
Looks like a GREAT start, I'll be keeping an eye on this build. That is a kick a$$ 1:1 rig! looks AND works good, perfect to emulate with an RC. |
looking awesome"thumbsup" |
looks good so far. i think the headlight hoops are too pointy but not sure due to the angle of the 1:1 pic. keep up the good work! |
Looks great man! Another FJ body huh "thumbsup" |
Wow, you cut up a proline fj :shock:. J/k that's a very cool start. Still haven't tried bending tube yet, looks fun. Good start, and great choice of vehicle. |
It is looking good. Do you have any good spots to crawl around College Station? My bro lives there(near the water tower) and my wife and I will be visiting for a few days around new years. I will have my tlt and sticky nylint and would love to do some crawling. BTW, it is UT, not TU. TU is Texas Utilities :flipoff: and I will be watchin the game too. |
looks like a good start"thumbsup" |
I've been meaning to update the post but this project has been like an American Chopper episode for me. I couldn't start till thursday and I had till noon on saturday to get it finished before heading back to college. And then what was supposed to be a 5 hour trip turned into a 9 hour trip with much excitement and boredom :shock: I finished the chassis early today and have it painted along with the front clip and side panels...which look great As for some of the pieces not being squared....I messed up at the begining. That is why I ended up cutting off the front and back and redoing those. As it sits now, the only problem that I can see is the bottom of the chassis which I think will be fine, just may need a small spacer for the links. I will probably cut the bottom half off and redo it over the christmas break if I go back home. Once I got a hang of the bending and brazing, Everything started lining up and became easyer. I was wondering the same thing about the link/shock mounts but after I finished it, I messed around with them and they seem stout. I don't think they will be a problem but only one way to find out. Nluvwithxlr8ing - I wish it was another FJ-40 body, but sadly the one that you painted for me was in an unfortunate roll while on my clod and started tearing by the body mounts. It was a bad design on my part :-(. Luckily I had you paint me that awesome UA Taco body. gotmuddy - No....it's TU "thumbsup" and that was one hell of a game. There was a park that had a nice spot but the last time I went there, they tore up the back section to widen a water run off ditch. Now I'm looking for a new place. There is one nice place that looks like fun but it just so happens to be a police stations sign/flower bed :twisted: I didn't have time to upload the pictures before I left but my dad should be doing that and emailing them to me, so I'll try to get them up tomorrow. I think it came out very well with the being my first one. Even if it doesn't crawl worth a dang, it will still be a fun rig. |
What game are you refering to then? The longhorn vs Aggie game? Cause the longhorns are UT(University of TX). http://www.utexas.edu/ BTW, I was born in Bryan(St. Joseph's) and raised in Navasota. |
Everyone around here calls UT, TU since we do not view this as the University of Texas, but merely a Texas university. "thumbsup" Just some good ole tradition I made the links last night and the wheelbase turned out to be just a hair under 13". I'm not to sure about the flex, but I think the links are binding and it will just take some playing with to get everything right. Check back later this evening and I'll have some pics up. |
How easily did the paint come out? I havent had a chance to strip one yet. |
It wasn't to bad. I just wiped some brake fluid on it and let it sit for probably 5 minutes and started scrubbing with an old rough cloth. The black came off real easy but the white was a little harder. The hardest part was getting it out of the little crevices, and I just used some que-tips. Probably took 15 minutes to do from the windshield forward. |
|
Delrin skid mounted :-P Second pic shows how I made the upper transmission mount. It also will have two screws coming up beneath it mounting it to the skidplate. Third pic....the chassis is sitting sideways, it's not really crooked like that ;-) http://tamor.us/members-rigs/albums/...8/DSC00028.jpg http://tamor.us/members-rigs/albums/...8/DSC00030.jpg http://tamor.us/members-rigs/albums/...8/DSC00031.jpg |
And finally, the paint, which will soon be scratch off on the rocks :twisted: You may notice where I completely wasn't paying attention and made the back electronics braket block where the driveshaft is supposed to go through :roll: I'll be cutting the bottom part off needless to say. http://tamor.us/members-rigs/albums/...8/DSC00033.jpg http://tamor.us/members-rigs/albums/...8/DSC00034.jpg .. .... ...... ........ .......... and now...... http://tamor.us/members-rigs/albums/...8/DSC00037.jpg http://tamor.us/members-rigs/albums/...8/DSC00035.jpg http://tamor.us/members-rigs/albums/...8/DSC00036.jpg This pictures don't do tha paint justice. It is a metalic red backed by a metalic gunmetal grey which is also the front bezel. If you look close at the side panels, the grey design is window tent so you can kind of see through it 8) I have the panels actually mounted now and they look great. Also finished up the links and it flexes alot better now. Already swapped the front springs out and just ordered some replacement springs for the rear. I still need to order the electrons to get this buttoned up. Hopefully the driveshaft yokes will be back in stock this week. As it sits now, it has a 13" wheelbase and 3.5" belly height. This is with no weight in it, so I imagine the ride height will drop some once the battery, esc, reciever, and trans/motor are mounted. |
Man that looks sweet"thumbsup" |
Quote:
|
All times are GMT -6. The time now is 05:21 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com