RCCrawler Forums

RCCrawler Forums (http://www.rccrawler.com/forum/)
-   Tamiya TLT Crawlers (http://www.rccrawler.com/forum/tamiya-tlt-crawlers/)
-   -   TLT Crawler Picture Archive (http://www.rccrawler.com/forum/tamiya-tlt-crawlers/6756-tlt-crawler-picture-archive.html)

RiceBurner 09-29-2012 09:58 PM

Re: TLT Crawler Picture Archive
2 Attachment(s)
Got my winnie on TLT's
Attachment 210692

Attachment 210693

bugman72 11-23-2012 07:40 PM

Re: TLT Crawler Picture Archive
Here's mine. Same TLT axles since 2005! "thumbsup"

  • Custom chassis made from Lexan and cutting board
  • TLT axles
  • KC_Jones clocked axle Cs
  • Savox 0251 Servo
  • Traxxas Mini Summit Transmission w/gear swap
  • Traxxas Mini Summit driveshafts (front)
  • Tamiya CC-01 telescoping metal driveshaft (rear)
  • Carrier bearing assembly using TA04 steering knuckle w/bearings
  • Holmes Hobbies Revolver Black Outrunner
  • HobbyWing EZRun 35A ESC
  • Sky Lipo 2S 40C 1300mah Lipo
  • FlySky GT-3B Tx/Rx (firmware modded)
  • 2.2 Rovers (white dot)

Build thread can be found HERE




Video - Goin' Up a Wall

Di$c0 07-08-2013 11:27 PM

Re: TLT Crawler Picture Archive
My second TLT build , first 1.9 scale.
Proline ambush CGR
3/8, 1/4 and 3/16 inch brake line cage and bumpers
Square tube frame
RC4WD delrin TLT axle housings
RC4WD straight axles rear
JB weld lockers
Tamiya leaf springs front ,4 link rear
Axial trans and 27 turn motor
Mamba Max Pro
Gens Ace 3s 1300 lipo
Axial simple light controller
Proline HID light buckets
11.25 wheel base, 8.25in tire width.
weighs 5lbs 7oz


Di$c0 10-31-2013 08:17 PM

Re: TLT Crawler Picture Archive
My first TLT build
Proline Baja VW
RBX laydown chassis
1/4 by .49 wall aluminum tubing links with Revo ball ends
Tamiya dark impact front wheels and masher 2ks
RC4WD straight alum axle
RC4WD straight axles rear
JB weld lockers
Traxxas trans and 12 turn motor
Mamba Max Pro
Gens Ace 3s 1300 lipo
12.5 wheel base
weighs 4.59 lbs

2013 TTC winner Jim's Pit Ruston, LA.


theTman 04-04-2014 12:10 AM

Re: TLT Crawler Picture Archive
I just pulled this old thing out of the closet: http://i.imgur.com/6SuPGBAl.jpg http://i.imgur.com/dkjuWkUl.jpg http://i.imgur.com/SG87lDfl.jpg http://i.imgur.com/VlUV8tVl.jpg

That's an old Gopher Tube chassis. It has aluminum body panels and a somewhat crude aluminum battery guard on the front axle. It is running droop suspension with Traxxas shocks and very soft springs under the piston that came from The Crawler store to help with stability as the tube chassis combined with normal shocks makes it quite top heavy. It has an old Losi XXX-T stadium truck transmission modified to work in a crawler (I was a kid without a real job at the time). It has a Mamba Max ESC I stole from that XXX-T of mine (I was sick of just zipping around a field with it, don't regret it one bit). It is running a 55T Integy motor and an HS-645MG Hitec servo. It has the cheap AM radio and receiver that came with the RTR XXX-T 8-10 years ago LOL. The suspension links and steering links are traxxis ends on some threaded rod from the hardware store with an automotive brake line sleeve over the threaded rod. The servo mount/ battery plate was from either The Crawler Store or RC4WD (I forget which). It has Traxxas driveshafts. The rims are some of the first beadlocks from Axial (I won them in a raffle with my local crawler group). There is some lead weight coiled inside the Rim where the axle goes (Not inside the tire though). The tires are Losi Rock Claws.

She never won a comp but she did decently, especially for a high school kid that only got to crawl on rocks a couple times a month due to lack of transportation.

joe.bielski 02-24-2015 08:10 PM

Re: TLT Crawler Picture Archive
This is my TLT 1.9 scale comp work horse.
TLT Axles
Front Axle: RC4WD Delrin housing, locked diff, MIP CVD's, High Steer Knuckes
Rear Axle: Aluminum Lock outs, stock internals

TCS X-trail Chassis, AX10 tranny, MIP Drive shafts, 45T Lathe Motor, Proline shocks w/Team Associated B4 rear springs, 60W oil all around, Sidewinder V3 ESC, running 2S batteries (sometimes 3S but low MAH limits torque), Gear heads wheels, Pitbull Rockbeast tires, spektrum s8000 servo, glitch buster.

Weight: 6.5Lbs RTR

This truck spanks hopped up SCX10 truck all day long and is bullet proof!!! ;)

(Sorry, pics are a bit old and missing MIP drive shafts and lock outs)




Di$c0 06-28-2015 12:23 AM

Re: TLT Crawler Picture Archive
3/8 tubing chassis
Tamiya Leaf front, 4 link rear
Integy 35t lathe motor
MMP esc with 11.1v GForce 2200mah lipo
RC4wd CVD front axles
Rc4wd stainless straight axles and rear alum housing
RC4wd rear shocks
Axial Deadbolt lexan
Axial 1.9 Krawler TA on Tamiya Highlift wheels
Axial tranny and rear driveshaft
Traxxas front driveshaft and ujoints


All times are GMT -6. The time now is 10:30 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2021, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com