12-13-2004, 04:34 PM | #1 |
Guest
Posts: n/a
| Parts for my txt-1
What do you guys think about me buying an novak evx two magnetic mayhem motors and two 9 tooth pinion from robinson racing.
|
Sponsored Links | |
12-13-2004, 04:38 PM | #2 |
Newbie Join Date: Oct 2004
Posts: 12
| Re: Parts for my txt-1
Or instead or 2 motors just buy one and a gear reduction. Cheaper and alot more power. Just my opinion though.
|
12-13-2004, 04:39 PM | #3 |
Guest
Posts: n/a
| Re: Parts for my txt-1
thanks i was thinkin of getting the gd 600 but i dont know how it goes on.
|
12-13-2004, 04:44 PM | #4 | |
Diggin' the new SCX10 II! Join Date: Mar 2004 Location: Norcal
Posts: 11,402
| Re: Parts for my txt-1 Quote:
| |
12-13-2004, 04:50 PM | #5 |
Guest
Posts: n/a
| Re: Parts for my txt-1
How about 9 tooth pinion gd 600 rooster not super and magnetic mayhem
|
12-13-2004, 05:00 PM | #6 |
Diggin' the new SCX10 II! Join Date: Mar 2004 Location: Norcal
Posts: 11,402
| Re: Parts for my txt-1
9t pinion and a gd600 with a mag mayhem will probably net you almost no wheel speed. You might need to bump up the pinion. The rooster with be fine with that as well, but you will need an rx pack for your servo/s. |
12-13-2004, 05:09 PM | #7 |
Guest
Posts: n/a
| Re: Parts for my txt-1
Thanks, what would be a good # tooth pinon to use on the motor? sorry, im new, and how do i mount the gd 600 to the tranny? and what tooth pinon should i use on the output shaft of the reducer? i also read that you need to file down the out put shaft to get the pinon to fit is that true Thanks A lot Badger
|
12-13-2004, 05:12 PM | #8 |
Diggin' the new SCX10 II! Join Date: Mar 2004 Location: Norcal
Posts: 11,402
| Re: Parts for my txt-1
OK, now you need to sit back and read some more. The answers to your questions are all here in other threads. Try searching a bit for some of your questions.
|
12-13-2004, 05:21 PM | #9 |
Guest
Posts: n/a
| Re: Parts for my txt-1
i knew you were going to make me search lol sorry if i put a lot on you
|
12-13-2004, 05:27 PM | #10 |
I wanna be Dave Join Date: Aug 2004 Location: san jose
Posts: 2,061
| Re: Parts for my txt-1
A good size pinion for this would be a 15 tooth and the output size you should run is the 3.8 with a m.m you should be around 130 to 1 final |
12-13-2004, 05:29 PM | #11 |
Guest
Posts: n/a
| Re: Parts for my txt-1
and the output size you should run is the 3.8 can you explain 3.8 |
12-13-2004, 06:02 PM | #12 |
RCC Addict Join Date: Jun 2004 Location: SERCRC
Posts: 1,680
| Re: Parts for my txt-1 I run a little higher gearing than a lot of folks, I like being able to get the tires spinning if I need momentum to hop up a ledge or rock. I'm running a Mag Mayhem on a GD600 with a 15T on the output. I have the torque to go slow but can pin the throttle and really spin the tires if the need arises. |
12-13-2004, 06:11 PM | #13 |
Guest
Posts: n/a
| Re: Parts for my txt-1
Its final im getting a super rosster two mag. mayhems with 9 tooth pinons gears ill deal with a gd 600 later What do you think |
12-13-2004, 06:19 PM | #14 | |
Diggin' the new SCX10 II! Join Date: Mar 2004 Location: Norcal
Posts: 11,402
| Re: Parts for my txt-1 Quote:
This thread really should be in the newbie section now. | |
| |